Summary of KD318MUI
Page 1
Four-port adsl router kd318mui adsl router user manual.
Page 2
Adsl router user manual notice this document contains proprietary information protected by copyright, and this manual and all the accompanying hardware, software, and documentation are copyrighted. All rights are reserved. No part of this document may be photocopied or reproduced by mechanical, elec...
Page 3
Content 1 overview .................................................................................................................................... 1 1.1 f eatures .......................................................................................................................... 1 1.2 p a...
Page 4: 1 Overview
Adsl router user manual 1 1 overview thank you for using this asymmetric digital subscriber line (adsl) router. With the asymmetric technology, this device runs over standard copper phone lines. In addition, adsl allows you to have both voice and data services in use simultaneously all over one phon...
Page 5
Adsl router user manual 2 ipoa 1.1.3 operating system support windows 98 windows 98 se windows me windows 2000 windows xp macintosh linux 1.1.4 atm capabilities atm connection vpi range: 0-255 vci range: 32-65535 aesa (e.164, dcc, icd) pvc support uni 3.0 & 3.1 signaling ...
Page 6
Adsl router user manual 3 1.1.6 environmental operating humidity: 10%-90% non-condensing non-operating storage humidity: 5%-95% non-condensing 1.2 packet contents the packet contents are as the following: adsl router x 1 external splitter x 1 power adapter x 1 telephone line x 1 ethern...
Page 7
Adsl router user manual 4 user name: admin password: adslroot vpi/vci: according to local information 1.5 warnings and cautions never install telephone wiring during storm. Avoid using a telephone during an electrical storm. There might be a risk of electric shock from lightening. do not i...
Page 8
Adsl router user manual 5 2 hardware description front panel led color function pwr green on: power on off: no power eth1-4 green on: lan link established and active via lan port blinking: adsl data activity occurs off: no lan link via lan port dsl green on:adsl link established and active quick bli...
Page 9
Adsl router user manual 6 rear panel port function dsl connect the device to an adsl telephone jack or splitter using a rj-11 telephone cable eth1,2,3,4 connect the device to your pc's ethernet port, or to the uplink port on your hub/switch, using a rj-45 cable reset system reset or reset to factory...
Page 10: 3 Installation
Adsl router user manual 7 3 installation 3.1 hardware installation this hardware installation describes how to connect adsl router to your computer, lan and the internet. This installation assumes you have subscribed to an isp for adsl service and only covers the basic configurations to be applied t...
Page 11
Adsl router user manual 8 3.2 software installation this chapter shows you how to install the router’s usb drivers when pc connects to the router via its usb port. 1. Insert the rectangular end of a usb cable into the usb port of your pc. 2. Insert the square end of the usb cable into the usb port o...
Page 12
Adsl router user manual 9 8. You will be prompted to restart windows. Click “yes”. 4.1.2 windows 2000 1. In the windows task bar, click the “start” button, point to “settings”, and then click “control panel”. 2. Double-click the “network and dial-up connections” icon. 3. In the “network and dial-up ...
Page 13
Adsl router user manual 10 4.2 access the program after configuring the ip address of you computer, powering on the adsl router, and launching a web browser, such as internet explorer, use http://192.168.1.1 to log on to the setting pages. Attention: the username and password are both lowercase. 4.3...
Page 14
Adsl router user manual 11 3. Click wan service from the left menu. 4. Click add to select a layer 2 interface for this service and then click next. 5. Choose wan service type, just choose pppoe for example here. You can enter your own service description here if you want and then click next..
Page 15
Adsl router user manual 12 6. Input ppp username & ppp password and then click next. The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password. Pppoe service name can be blank unless your internet service provider gives you a value to enter...
Page 16
Adsl router user manual 13 authentication method is default to auto. It is recommended that you leave the authentication method in auto, however, you may select pap or chap if necessary. The default value for mtu (maximum transmission unit) is 1500 for pppoa and 1492 for pppoe. Do not change these v...
Page 17
Adsl router user manual 14 8. Get dns server information from the selected wan interface or enter static dns server ip addresses. If only a single pvc with ipoa or static mer protocol is configured, you must enter static dns server ip addresses. 9. Make sure that the settings below match the setting...
Page 18
Adsl router user manual 15 4.3.2 router mode setup 1. From advanced setup, click layer2 interface and select eth interface. Before you configure eth wan interface, you ’d better remove all pvc settings from atm interface. 2. Click add and you ’ll see the following screen..
Page 19
Adsl router user manual 16 3. Select a eth port as you will. You can select enet1, enet2, enet3 or enet4 port as the wan interface and default mode as connection mode. 4. Click apply/save and you ’ll see the following screen. 5. From advanced setup, click wan service to configure a wan service over ...
Page 20
Adsl router user manual 17 7. Click next and you ’ll see the following screen. Select pppoe as wan service type for example. Click next. 8. Enter the user name and password that your isp has provided to you. Click next..
Page 21
Adsl router user manual 18 pppoe service name can be blank unless your internet service provider gives you a value to enter. Authentication method is default to auto. It is recommended that you leave the authentication method in auto, however, you may select pap or chap if necessary. The default val...
Page 22
Adsl router user manual 19 the ppp ip extension is a special feature deployed by some service providers. Unless your service provider specifically requires this setup, do not select it. If you need to select it, the ppp ip extension supports the following conditions: it allows only one computer on t...
Page 23
Adsl router user manual 20 10. Get dns server information from the selected wan interface or enter static dns server ip addresses. Click next. 11. Make sure that the settings below match the settings provided by your isp. Click on the apply/save button to save your configurations and reboot the adsl...
Page 24
Adsl router user manual 21 4.3.3 remote access when the firewall is enabled on a wan or lan interface, all incoming ip traffic is blocked. However, some ip traffic can be accepted by setting up filters. 1. Select advanced setup=>security=>ip filtering=>incoming and choose add or remove to configure ...
Page 25
Adsl router user manual 22 4.3.4 tr069 client wan management protocol (tr-069) allows a auto-configuration server (acs) to perform auto-configuration, provision, collection, and diagnostics to this device. Inform: whether or not the cpe must periodically send cpe information to server using the info...
Page 26
Adsl router user manual 23 used for tr069 connection request user name: username used to authenticate the cpe when making a connection to the acs using the cpe wan management protocol. This username is used only for authentication of the cpe. Connection request password: password used to authenticat...
Page 27
Adsl router user manual 24 appendix frequent asked questions q: none of the leds are on when you power on the adsl router? A: please make sure what you use is the power adaptor attached with the adsl router package，and check the connection between the ac power and adsl router. Q: dsl led does not tu...
Page 28
Adsl router user manual 25 q: initialization of the pvc connection failed? A: be sure that cable is connected properly from the dsl port to the wall jack. The dsl led on the front panel of the adsl router should be on. Check that your vpi, vci, type of encapsulation and type of multiplexing setting ...