Summary of KW5862
Page 1
Kw5862 wifi adsl gateway user manual.
Page 2
Wlan adsl gateway user manual notice this document contains proprietary information protected by copyright, and this manual and all the accompanying hardware, software, and documentation are copyrighted. All rights are reserved. No part of this document may be photocopied or reproduced by mechanical...
Page 3: Content
Content 1 overview .............................................................................................................................. 1 1.1 f eatures ......................................................................................................................... 1 1.1.1 data rat...
Page 4
Wlan adsl gateway user manual 1 1 overview thank you for choosing our product. The kw5862 is a wireless adsl router combining an adsl modem, an 802.11n wireless router, a 4-port switch, two fxs ports and a usb host port in one unit, bringing high-speed wireless internet connection to a home or offic...
Page 5
Wlan adsl gateway user manual 2 1.1.4 network protocol & features ethernet to adsl self-learning transparent bridging internet control message protocol (icmp) ip static routing routing information protocol (rip, ripv2) network address translation (nat) virtual server, port forwarding dynamic host co...
Page 6
Wlan adsl gateway user manual 3 voice codecs: g.711a/µ, g.723, g.726, g.729 call waiting call forwarding 1.1.7 firewall built-in nat mac filtering packet filtering stateful packet inspection (spi) denial of service prevention (dos) dmz 1.1.8 management support web based gui upgrade or update via ftp...
Page 7
Wlan adsl gateway user manual 4 1.1.10 environmental operating humidity: 10%-90% non-condensing non-operating storage humidity: 5%-95% non-condensing 1.2 packet contents the packet contents are as the following: adsl router x 1 external splitter x 1 power adapter x 1 telephone line x 1 ethernet cabl...
Page 8
Wlan adsl gateway user manual 5 1.5 warnings and cautions never install telephone wiring during storm. Avoid using a telephone during an electrical storm. There might be a risk of electric shock from lightening. Do not install telephone jacks in wet locations and never use the product near water. To...
Page 9: 2 Hardware Description
Wlan adsl gateway user manual 6 2 hardware description front panel led color function power green on: power off: no power eth1,2,3,4 green on: lan link established and active via lan port blinking: adsl data activity occurs off: no lan link via lan port wlan green on: the wireless module is ready an...
Page 10
Wlan adsl gateway user manual 7 rear panel port function dsl connect the device to an adsl telephone jack or splitter using a rj-11 telephone cable fxs1 connect the device to your normal phone reset system reset or reset to factory defaults. Usb connect the device to your printer eth1,2,3,4 connect ...
Page 11: 3 Hardware Installation
Wlan adsl gateway user manual 8 3 hardware installation this chapter shows you how to connect router. Meanwhile, it introduces the appropriate environment for the router and installation instructions. 1. Using a telephone line to connect the dsl port of router to the modem port of the splitter, and ...
Page 12
Wlan adsl gateway user manual 9 4 pc configuration guide 4.1 local pc configuration in windows 95, 98, me, xp 1. In the windows task bar, click the “start” button, point to “settings”, and then click “control panel”. 2. Double- click the “network” icon. 3. On the “configuration” tab, select the tcp/...
Page 13
Wlan adsl gateway user manual 10 5 web-based management guide in order to use the web-based management software it will be necessary to use a computer that occupies the same subnet as the router. The simplest way to do this for many users will be to use dhcp server that is enabled by default on the ...
Page 14
Wlan adsl gateway user manual 11 we can select wizard setup or advanced setup mode to setup kw5862.The wizard set up will guide us for a basic setting,and the advanced setup will guide us to home page for more detailed setup. 5.2 internet access configuration 5.2.1 adsl mode setup from home page, yo...
Page 15
Wlan adsl gateway user manual 12 3. Click wan service from the left menu. 4. Click add to select a layer 2 interface for this service and then click next . 5. Choose wan service type, just choose pppoe for example here. You can enter your own service description here if you want and then click next ...
Page 16
Wlan adsl gateway user manual 13 pppoe service name can be blank unless your internet service provider gives you a value to enter. Authentication method is default to auto . It is recommended that you leave the authentication method in auto , however, you may select pap or chap if necessary. The def...
Page 17
Wlan adsl gateway user manual 14 the gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the dial on demand check box and entering the inactivity timeout . The entered value must be between 1 minute and 4320 minutes. The ppp ip extension is a sp...
Page 18
Wlan adsl gateway user manual 15 8. Get dns server information from the selected wan interface or enter static dns server ip addresses. If only a single pvc with ipoa or static mer protocol is configured, you must enter static dns server ip addresses. 9. Make sure that the settings below match the s...
Page 19
Wlan adsl gateway user manual 16 5.2.2 router mode setup 1. From advanced setup , click layer2 interface and select eth interface . Before you configure eth wan interface, you ’d better remove all pvc settings from atm interface . 2. Click add and you ’ll see the following screen. 3. Select a eth po...
Page 20
Wlan adsl gateway user manual 17 5. From advanced setup , click wan service to configure a wan service over the interface you selected. 6. Click add and you ’ll see the following screen. 7. Click next and you ’ll see the following screen. Select pppoe as wan service type for example. Click next ..
Page 21
Wlan adsl gateway user manual 18 8. Enter the user name and password that your isp has provided to you. Click next ..
Page 22
Wlan adsl gateway user manual 19 pppoe service name can be blank unless your internet service provider gives you a value to enter. Authentication method is default to auto . It is recommended that you leave the authentication method in auto , however, you may select pap or chap if necessary. The def...
Page 23
Wlan adsl gateway user manual 20 the gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the dial on demand check box and entering the inactivity timeout . The entered value must be between 1 minute and 4320 minutes. The ppp ip extension is a sp...
Page 24
Wlan adsl gateway user manual 21 10. Get dns server information from the selected wan interface or enter static dns server ip addresses. Click next . 11. Make sure that the settings below match the settings provided by your isp. Click on the apply/save button to save your configurations and reboot t...
Page 25
Wlan adsl gateway user manual 22 5.2.3 lan settings from lan , configure the dsl router’s ip address and subnet mask for lan interface. In this page, you can use dhcp (dynamic host configuration protocol) to control the assignment of ip addresses on your local network (lan only).Kw5862 support ipv4 ...
Page 26
Wlan adsl gateway user manual 23 item description ip address this is the ip address that other devices on your local network will use to connect to the modem. Subnet mask this defines the size of your network. The default is 255.255.255.0 . Enable igmp snooping igmp snooping is a method that actuall...
Page 27
Wlan adsl gateway user manual 24 5.2.3.2 ipv6 lan settings item description ipv6 address this is the ip address that other devices on your local network will use to connect to the modem. Subnet mask this defines the size of your network. The default is 255.255.255.0 . Enable igmp snooping igmp snoop...
Page 28
Wlan adsl gateway user manual 25 use blocking mode to discard unknown multicast traffic. Disable / enable dhcp server the dhcp server assigns an ip addresses from a pre-set pool of addresses upon request from dhcp client (e.G. Your computer). Do not disable the dhcp server unless you wish to let ano...
Page 29
Wlan adsl gateway user manual 26 5.3 wireless setting 5.3.1 basic option description enable wireless a check box that enables or disables the wireless lan interfaces. The default is to enable wireless communications. Hide access point select hide access point to protect the adsl route access point f...
Page 30
Wlan adsl gateway user manual 27 bssid displays the gateway's wireless mac address. (user may need this address if user is using wds or multiple gateways.) click apply to save changes. Country drop-down menu that allows selection of specific channel. 5.3.2 advanced settings this page is where user s...
Page 31
Wlan adsl gateway user manual 28 warning: the settings shown above are default settings. Changes made to these items can cause wireless communication problems. Field description band this is the range of frequencies the gateway will use to communicate with user’s wireless devices. Channel drop-down ...
Page 32
Wlan adsl gateway user manual 29 multicast messages for its clients, it sends its next dtim message with this dtim interval value. The clients hear the beacons and awaken as needed to receive the broadcast and multicast messages. Beacon interval the amount of time (in milliseconds) between beacon tr...
Page 33
Wlan adsl gateway user manual 30 2.Configure wpa pre-shared key as below and click apply/save . 3.Enable wps as below..
Page 34
Wlan adsl gateway user manual 31 4.Set wps ap mode as unconfigured and click config ap . 5. Set wps ap mode as configured and click save/apply. 6.Now you can use a wireless adaptor with wps function and the wps button to connect to access the internet. 7. To configure security features for the wirel...
Page 35
Wlan adsl gateway user manual 32 the wireless security page allows user to configure the security features of user’s wireless network. There are several security methods to choose from, depending on user’s needs and the capabilities of user’s wireless machines. Wep open and wep shared —wep is an enc...
Page 36
Wlan adsl gateway user manual 33 the weaknesses in wep. Any client capable of wpa encryption should use it instead of wep. Wpa (psk) — this is wpa encryption combined with a pre-shared key (psk) , which is a text string known only to the gateway and authorized wireless clients. The gateway rejects t...
Page 37
Wlan adsl gateway user manual 34 interface name: pvc channel for voip service. Locale selection: keep the value as default if without any request from your isp. Preferred codec list: voice codecs. Sip proxy : sip proxy server address or domain name of sip service. You can make it blank if your isp h...
Page 38
Wlan adsl gateway user manual 35 sip registrar : the sip server address provide by your isp. This address is necessary for voip setting. Sip registrar port : the signal port of sip server. The default value is 5060. Extension: sip account username provided by your isp. The value is necessary for voi...
Page 39
Wlan adsl gateway user manual 36 line forwarding number: forward the incoming call to the number you typed. Select checkbox to enable the call forwarding function. Enable mwi . Mwi means message-waiting indication. Usually an audio or visual signal that a voicemail or other type of message is waitin...
Page 40
Wlan adsl gateway user manual 37 4. Select connect to a printer on the internet, type “ http://192.168.1.1:631/printers/printer ” and click “next”. The printer name “printer” must be the same name entered in the adsl router “print server setting” as in step 1 . 5. Select driver file directory on cd-...
Page 41
Wlan adsl gateway user manual 38 7. Click “finish”. Appendix: frequent asked questions q: none of the leds are on when you power on the adsl router? A: please make sure what you use is the power adaptor attached with the adsl router package and checks the connection between the ac power and adsl rou...
Page 42
Wlan adsl gateway user manual 39 please make sure that you use parallel network cable to connect uplink port of hub, or use parallel network cable to connect pc. If connect normal port of hub (not uplink port), you must use cross-cable. Please make sure that your network cables meet the networking r...
Page 43
Wlan adsl gateway user manual 40