Mobiset 2 digital cap 610 translation of the original operating manual - englisch -.
2 general dear customer, chère cliente, cher client, gentile cliente, estimado cliente, gb you can obtain an english version of our mounting instructions from our representatives in your country (http://www.Kathrein.De/include/kontakte_groups_eng.Cfm?Kontinent=1&gruppe=sat) or download one from our ...
3 mobiset 2 cap 610 components/scope of delivery ufs 940sw (front view) the mobiset 2 digital cap 610 consists of: • turntable complete with control electronics, pre-assembled planar antenna with lnb • mounting plate • complete cabling set: 1 x coax cable 8 m long, and one power supply cable (10 m) ...
4 general ................................................................................................................................. 2 mobiset 2 cap 610 components/scope of delivery ...................................................... 3 contents ................................................
5 contents (operating manual) cap 610 operating manual ............................................................................................... 46 important information for cap 610 before setup .................................................... 47 remote control ...............................
6 proper use the mobiset 2 digital cap 610 is designed to receive digital tv and radio programs via satellite. The automatic positioner is intended to be used as a turntable for the kathrein planar antenna. The turntable can be used to receive digital tv and radio signals in the frequency range from...
7 safety instructions - important notes safety during installation work when carrying out installation work in locations where there is a risk of falling, take appropriate safety precautions, e.G. Use of a working platform. Make sure that the vehicle roof is suffi ciently strong and stable to carry ...
8 road traffi c licensing regulations (stvzo) the applicable regulations of the stvzo must be observed in respect of fi xed installation of the turntable on a vehicle which is driven on public highways. In particular, §§ 19/2; 30 c; 32 (2) and the ec directive 74/483 eec are applicable. Briefl y, th...
9 the antenna will be lowered within 12 seconds of the ignition being switched on (if the unit is in stand-by mode or the ufs 940sw is switched off). Otherwise the control unit that is in use is lowered immediately. Important: lowering the antenna can take up to 30 seconds after the ignition is swit...
10 • circular cutter, Ø 38 mm • flat-bladed screwdriver for m5 screws • power drill • galvanised round head screws, depending on the roof structure (Ø: 5 mm, sheet metal screws d 7981, depending on the roof structure) or round head screws d 7985 with washers and nuts • twist drill, Ø 2.5 or 5.5 mm •...
11 • when selecting the installation position, take into account the range of movement of the turntable (see graphics and the “technical specifi cations” chapter). There must be no structures on the roof that would obstruct this range of movement (risk of collision). For safety, keep at least the re...
12 • choose an installation position on the roof that is as horizontal as possible or only slightly sloping: depending on the location of the vehicle, roof pitches greater than 5° may lead to problems when searching for the satellite. • to ensure secure adhesion, the height difference of the roof cu...
13 • mark out the positions of the six fastening holes on the roof of the vehicle in a circular pattern. Note: the size of the holes and the choice of fastening screws to be used (not supplied) depend on the type and thickness of the materials used in the roof structure. If the roof panelling (plast...
14 • create the holes necessary to secure the mounting plate (fig. C). • in addition to the bolted connection, the mounting plate and roof gland must be bonded to the roof with adhesive and sealed. This is done using the sikafl ex® 291 adhesive sealant supplied, which is ideally suited for this purp...
15 • ensure before starting adhesive work that the temperature of materials to be glued and the sealant is between +5 °c and +40 °c. Prepare all necessary fastening elements and tools. • prepare the tube of adhesive sealant in accordance with the instructions enclosed with the tube. • remove the roo...
16 figure: e installation and connection • lift up the turntable and place it carefully on the mounting plate facing in the direction of travel (see illustration fig. E) (do not step on the plug connectors and do not kink/crush the cables!) the through holes on the turntable must be perfectly aligne...
17 installation and connection version with external cable gland (fig. F) • the external roof gland is arranged so that it forms a water-tight enclosure on the vehicle roof around the point where the two cables projecting from the turntable are connected to the two extension cables within the interi...
18 installation and connection brief instructions for installing the turntable the other detailed instructions in this installation and operating manual must also be followed! For ease of illustration, we have dismounted the bas 60 on these photographs. As supplied, the bas 60 is pre-assembled to th...
19 align the mounting plate. Arrow in the direction of travel. Mark out the six holes for securing the mounting plate. Apply sikafl ex® 291 adhesive in a sinuous line between the two grooves and spread with spatula or similar. Avoid skin contact! Place mounting plate on roof gland and secure with ap...
20 installation of the ufs 940sw the four screw sockets provided (see diagram on the next page) allow you to install the receiver not only resting on a shelf but also to fi x it there or in other positions. Installation and connection note: when choosing the installation location, bear in mind that ...
21 removing the blanking plugs: when the unit is delivered, the screw sockets are covered with blanking plugs. These can be pushed out, using the screws supplied (working upwards from below, see diagram on the right). Preparations installation and connection attaching the infra-red sensor: if the un...
22 using the adhesive strips supplied, now install the infra-red sensor either on the receiver or at the chosen location. If the infra-red sensor is installed on the unit, its cable can be threaded in at its base, as for a phone, and routed to the rear of the receiver (see diagram on the right). Whe...
23 useful information for installing the receiver on a tv set: for installation by attachment to the rear of a tv set, securing with two screws is suffi cient. The equipment must have one of the following hole patterns (for wall mounting) on its rear panel: 100 x 100; 100 x 200; 200 x 200 or 200 x 4...
24 installation and connection secure the receiver at the installation location previously selected and prepared. Do not force it, and take care not to damage either the screw sockets, the receiver casing itself or any cables that are already attached to the receiver! Installation screw projection.
25 • lay the coaxial cable to the ufs 940sw. • lay the turntable power supply cable (3-pin plug) to the battery. Avoid laying the cables across sharp edges and secure the cables against possible chafi ng points. • connect the coaxial cable (coming from the turntable) to the “if in” f socket on the r...
26 installation and connection under certain circumstances, problems can arise when the units are connected to different connecting sockets or circuits/earth potentials. If no others are available, it is recommended that you connect the connecting sockets for receiver and tv set to the same cable, a...
27 important: for operation with two batteries, it must be ensured that the ignition signal earth has the same potential as the power supply battery earth for the turntable. Non-compliance means that the automatic lowering function will not work! Ensure the cable polarity is correct! Figure: g insta...
28 reception range/footprint the footprint is the reception area on the earth that a satellite covers with its transmission beam (spot), within which satellite reception is possible. The transmission power is at its greatest in the centre of this spot – it becomes progressively weaker moving outward...
29 if repairs to the system or individual components are necessary, contact your specialist dealer or our service centre (see below for address). • the cables laid within the vehicle can remain there • unscrew the six m6 screws securing the turntable to the mounting plate • place two wooden supports...
30 however, we expressly draw attention to the fact that positioning the bas 60 antenna at a deviation of +15° or -15° from the centre position only makes sense if a satellite to the far west or the far east is actually preferred for reception. Polarisation setting as supplied, the bas 60 is mounted...
31 polarisation setting safety instructions we strongly advise that users who are not familiar with the installation work should not reas- semble the bas 60 independently. They should contact a technician or engineer. They may fi nd a suitable person on the campsite. Make sure that: - the antenna an...
32 the explanation of this installation process is based on the assumption that the entire cap unit has been properly put together, installed and set up, as described in this installation manual. The safety instructions in the detailed operating manual for the ufs 940sw must also be followed! Instal...
33 12. You can now refi t the antenna with the desired change of angle (+15° or -15°) (see picture below). 13. Tighten the hexagon socket screws to a torque of 6-7 nm. 14. Leave the installation location and reconnect the ufs 940sw to the power supply. 15. First switch the receiver on at the main sw...
34 if a defect arises in the electronic controls, after some disassembly work the satellite dish can be returned to the park position (horizontal position) manually. Following this however, recalibration by an authorised workshop is always necessary. Driving to the nearest workshop with the antenna ...
35 1. In the centre of the axis (arrowed) there is a plastic cap. Lever this off with a narrow slot-head screwdriver. 2. Behind the cap is an m8 hexagon head screw. Unscrew this using a 13 mm socket wrench. After removing the m8 screw, a further thread can be seen. 3. Caution! Secure and support the...
36 technical specifications dimensions (mm) direction of travel mounting plate 118.3 118.3 153.6 282 143.5 approx. 17.
37 technical specifications min. Recommended clearance Ø 880 rotary axis bas 60 roof gland nut clamping range 20/50 weight incl. Bas 60: approx. 13.8 kg mounting plate 145.5 including mounting plate 143.5.
38 technical specifications type cap 610 order no. 20310018 lnb 1 output switchable: v/h (14/18 v), low/high (0/22 khz) lnb supply voltage v vertical: 11.5-14, horizontal: 16-19 input frequency ghz 10.70-12.75 output frequency mhz 950-1950/1100-2150 oscillator frequency (l.O.) ghz 9.75/10.60 system ...
39 sikaflex ® 291 safety data sheet 1. Materials/preparation and company designation data on the product (trade name): sikafl ex ® 291 data on manufacturer/suppliers manufacturer/suppliers: sika deutschland gmbh street/postcode: kornwestheimer str. 103-107 postcode and town: stuttgart country: germa...
40 5. Measures for fi re fi ghting suitable extinguishing media compatible with all extinguishing media in general use. Special hazard from the product, its products of combustion or gases released in case of fi re the following can be released: carbon monoxide (co) carbon dioxide (co 2 ) hydrogen c...
41 4.4‘ methylene-diphenyl-diisocyanate 101-68-8 permissible workplace concentration 0.05 mg/m 3 trgs 900/de/2004 101-68-8 permissible workplace concentration 0.005 ml/m 3 trgs 900/de/2004 xylol 1330-20-7 permissible workplace concentration 440 mg/m 3 trgs 900/de/2004 1330-20-7 permissible workplace...
42 11. Toxicology data sensitisation sensitisation/allergic reactions may occur. Sensitive individuals may exhibit allergic reactions even at very low concentrations. Experience of human exposure on skin contact: may lead to irritation on eye contact: may lead to irritation on being breathed in: may...
43 risk phrases 42 sensitisation possible by breathing in. Safety phrases 23 do not breathe in gas/smoke/vapour/aerosol. 45 in the event of accident or feeling unwell summon a doctor immediately (if possible show the doctor this label). Special identifi cation of particular components contains isocy...
44 sikaflex ® 291 technical data sheet si kafle x ® -291 1 / 2 technisches merkblatt version 12 / 2005 sikaflex ® -291 der haftstarke marine-dichtstoff technische eigenschaften chemische basis 1-k polyurethan farbe weiss, schwarz, holz härtungsmechanismus feuchtigkeitshärtend dichte vor aushärtung (...
45 sikaflex ® 291 technical data sheet si kafle x ® -291 2 / 2 weitere informationen internet: www.Sika-industry.De, e-mail: industry@de.Sika.Com www.Sika.Com sika deutschland gmbh kleb- und dichtstoffe industrie stuttgarter strasse 139 d-72574 bad urach deutschland tel. +49 7125 940-761 fax +49 712...
46 cap 610 operating manual the operating manual for the cap 610 if, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly, or if unexpected problems occur, please contact your specialist dealer. The kathrein technical customer sup...
47 all settings on the ufs 940 are made using the remote control! Important information for cap 610 before setup remote control so as to avoid overheating the turntable motors, do not operate the motors continuously for longer than 20 minutes. None of the search procedures initiated by the cap 610 w...
48 first installation before using your unit for the fi rst time, read the “safety instructions - important information” and “installation and connection” sections. You will fi nd a sample confi guration for a motor home in the section “installation and connection”, “connection example”. Do not conn...
49 the following display appears: press the (green) button to move to the next menu. Use the buttons to select whether to replace the factory pre-programmed channel list by a pre-sorted channel list for a specifi c country (at present only a limited number of pre-sorted channel lists are available)....
50 first installation system use the buttons here at “system” to select “cap”. Then use the buttons to select the “initialize cap” line and press the button to confi rm. Show 4:3 event here you can select the type of screen display mode for 4:3 broadcasts on a 16:9 tv set: - normal (pillarbox) - str...
51 first installation local time offset (utc) here you can use the buttons to select the local time offset to utc (formerly gmt) (e.G. For germany: + 1 hour). You can set the offset in 1 hour steps. The maximum offset is 12 hours (+ and -). Automatic clock change (summer/winter time) use the buttons...
52 cap menu (turntable antenna settings) press the (green) button. The following display appears: use the buttons to select the “antenna confi guration” line and press the button to confi rm. The following display appears: you can also call up this menu via the main menu “settings”, “antenna confi g...
53 this function should be used only by experienced users. Exact knowledge of the satellite position and your present location are necessary when aligning the antenna manually to a satellite. Watch out for any obstacles that the antenna might collide with. The antenna is liable to be damaged by such...
54 cap menu (turntable antenna settings) using the numeric keys and/or the buttons, input the desired elevation value. Two seconds after completion of the input or when the button is pressed, the cap moves to the selected position. Elevation this function is not available on the cap 610. Lnb tilt/sk...
55 this menu allows important basic settings for the cap, such as the elevation border or elevation offset to be set. These two settings in particular should be performed by a specialist to match your needs and the conditions; if they are set incorrectly the cap may be damaged! Use the buttons to se...
56 if the vehicle is not on supports during the search process and people are moving around inside it, there is a risk that movement of the vehicle will mean that the satellite is not found. Alignment (satellite search) the antenna is aligned automatically. After the ufs 940sw has been switched on, ...
57 channel (satellite) selection/programming the timer providing you are not in a menu, pressing the button calls up the channel list. The following display appears: by pressing the buttons all channels can be selected in the sequence that they appear in the current channel list and its sorting. Pre...
58 timer programming to prevent the turntable rotating at a time when it is unsupervised or when rotation might be irritating (e.G. In the middle of the night), a timer can be set. During the timer period the turntable is active only if the ufs 940sw is in operation or is in standby mode. If the rec...
59 after a change of location, the antenna moves to the last position selected. After initialisation, you will therefore see the following display (example, as it depends on the last selected position): for slight changes of location, the antenna can fi nd the satellite very quickly. If the search i...
60 you have four options for “parking” the antenna. 1. The antenna can be moved to park position by pressing the button twice. 2. Press the (green) button. Use the buttons to select the “move cap to park position” line and press the button to confi rm. 3. Press the button to return to the main menu....
61 special messages from the turntable the following messages are shown on the screen to protect your reception system and the on-board power supply: system protection messages the power supply to the turntable is inadequate (battery voltage below the minimum value). The turntable can still be moved...
62 the vehicle ignition was switched on. For safety reasons, the turntable moves into the park position. This operates however only if the green ignition cable for the turntable is connected to the vehicle ignition and the turntable is connected to the power supply! As long as voltage is present at ...
63 special messages from the turntable a serious software error has occurred. Reset the turntable in the cap menu, or contact our service centre. Messages arising from software problems the turntable antenna software is defective. An update is required. Contact our service centre. The connection to ...
64 special messages from the turntable the satellite you have selected cannot be received from your current location, or there may have been changes made using the “cap settings” menu (see section “cap menu (turntable antenna settings), cap settings”), as a result of which the desired satellite cann...
65 declaration of conformity.
66 disposal instructions electronic equipment is not domestic waste - in accordance with directive 2002/96/ec of the european parliament and the council dated 27 th january 2003 on used electrical and electronic appliances, it must be disposed of properly. At the end of its service life, take this d...
67 for your notes.
Internet: http://www.Kathrein.De kathrein-werke kg • anton-kathrein-straße 1 - 3 p.O. Box 100 444 • 83004 rosenheim • germany 936.3671/-/0410/zwt - technical data subject to change..