1. DL manuals
  2. Kathrein
  3. TV Accessories
  4. HDS 910
  5. Operating Manual

Kathrein HDS 910 Operating Manual

Manual is about: CAP upgrade kit

Summary of HDS 910

  • Page 1

    - english - translation of the original operating manual cap upgrade kit hds 910

  • Page 2: General

    2 general company address and accredited representative kathrein-werke kg anton-kathrein-straße 1 - 3 po box 10 04 44 83022 rosenheim distinguished businessman prof. Dr. Dr. H. C. Kathrein, mba personally liable managing director of kathrein-werke kg chère cliente, estimado cliente, f vous pouvez ob...

  • Page 3

    3 hds 910 components / scope of supply ufs 940sw (front view) the hds 910 upgrade kit consists of: • hds 900 control unit • 1 x coaxial cable 9 m long (for use in connection with cap 210/310), • 1 x 8-pin cable adapter 0.15 m long (for use in connection with cap 100) • 1 x 2-pin cable adapter 0.15 m...

  • Page 4

    4 general ................................................................................................................................. 2 hds 910 components / scope of supply .......................................................................... 3 contents (installation manual) ................

  • Page 5: Contents (Operating Manual)

    5 contents (operating manual) cap 610 operating manual ............................................................................................... 22 important information for cap before setup .......................................................... 23 remote control .............................

  • Page 6: Proper Use

    6 when any of the above cap units is upgraded by means of the hds 910 upgrade kit, no changes to the turntable and/or the bas 60 are necessary! The existing cabling can also still be used! A bas 50 planar antenna in use hitherto must be replaced with a bas 60 (bn 216195) (this applies only in connec...

  • Page 7: Sonnel!

    7 the system may only be installed by qualifi ed pecialist per- sonnel! To prevent hazards during installation, operation or when driving on public highways, the in- structions and information in this manual must be strictly adhered to. Proper performance of the upgrade of the system is a pre-requis...

  • Page 8

    8 safety instructions - important notes proper installation and safety essential information the correct execution of the upgrade (for instance the electrical connection work) is important for safety. Modifi cations to the electrical installations in the vehicle should only be carried out by a speci...

  • Page 9: Installation And Connection

    9 installation and connection before starting any installation work, it is essential you disconnect all the units con- cerned from the mains. Risk of fatal injury due to electric shock! • flat-bladed screwdriver for m5 screws • cross-head screwdrivers for m3 and m5 screws required tools and equipmen...

  • Page 10: Installation And Connection

    10 installation and connection installing the new control unit disconnecting the connections to the old control unit • mark the coaxial cable that comes from the turntable to the control unit (port: “if in”), so that it will not later be confused with the coaxial cable that runs to the receiver. • n...

  • Page 11: Installation And Connection

    11 installation and connection use of other screws: if because of the installation location or fac- tors associated with it, the screws supplied cannot be used, refer to the diagram along- side when selecting the screws to be used. This shows you the cross-section area of the screw sockets on the co...

  • Page 12: Installation And Connection

    12 the fuses in the cable and in the control unit must never be bridged – cable fi re hazard! Connecting the control unit • connect the coaxial cable (that comes from the turntable) to the “if in” port • now connect the other cables to the new control unit if any cable connection cannot be made beca...

  • Page 13: Installation And Connection

    13 installation and connection connection example for a caravan hds 900 ufs 940sw hdtv receiver * ) * ) * ) for a cap 100 system, use the cable adapters supplied note! Do not connect. Option not available! The antenna must be lowered before driving away. • switch on the receiver. • select hdp menu. ...

  • Page 14: Installation And Connection

    14 installation and connection connection example motor home hds 900 hdtv-receiver ufs 940sw * ) * ) * ) bei cap 100-anlage die beigelegten kabeladapter verwenden connection example motor home 12 v battery connection control unit green brown white battery 10.9 v-13.8 v ignition.

  • Page 15: Installation And Connection

    15 installation and connection installation of the ufs 940sw the four screw sockets provided (see diagram on the next page) allow you to install the receiver not only resting on a shelf but also to fi x it there or in other positions. Note: when choosing the installation location, bear in mind that ...

  • Page 16: Installation And Connection

    16 removing the blanking plugs: when the unit is delivered, the screw sockets are covered with blanking plugs. These can be pushed out, using the screws supplied (working upwards from below, see diagram on the right). Preparations attaching the infra-red sensor: if the unit is installed in open view...

  • Page 17: Installation And Connection

    17 using the adhesive strips supplied, now install the infra-red sensor either on the receiver or at the chosen location. If the infra-red sensor is installed on the unit, its cable can be threaded in at its base, as for a phone, and routed to the rear of the receiver (see diagram on the right). Whe...

  • Page 18: Installation And Connection

    18 useful information for installing the receiver on a tv set: for installation by attachment to the rear of a tv set, securing with two screws is suffi cient. The equipment must have one of the following hole patterns (for wall mounting) on its rear panel: 100 x 100; 100 x 200; 200 x 200 or 200 x 4...

  • Page 19: Installation And Connection

    19 secure the receiver at the installation location previously selected and prepared. Do not force it, and take care not to damage either the screw sockets, the receiver casing itself or any cables that are already attached to the receiver! Installation screw projection installation and connection.

  • Page 20: Installation And Connection

    20 avoid laying the cables across sharp edges and secure the cables against possible chafi ng points. • connect the coaxial cable (coming from the turntable) to the “if in” f socket on the rear of the ufs 940sw. • place the infra-red sensor for the receiver close to or directly on top of the tv set ...

  • Page 21: Installation And Connection

    21 under certain circumstances, problems can arise when the units are connected to different connecting sockets or circuits/earth potentials. If no others are available, it is recommended that you connect the connecting sockets for receiver and tv set to the same cable. The current rating of the cir...

  • Page 22: Cap 610 Operating Manual

    22 cap 610 operating manual the operating manual if, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly, or if unexpected problems occur, please contact your specialist dealer. The kathrein technical customer support is also at ...

  • Page 23

    23 all settings on the ufs 940 are made using the remote control! Important information for cap 610 before setup remote control so as to avoid overheating the turntable motors, do not operate the motors continuously for longer than 20 minutes. None of the search procedures initiated by the cap will ...

  • Page 24: First Installation

    24 before using your unit for the fi rst time, read the “safety instructions – important infor- mation” and “installation and connection” sections. Do not connect the unit to the power supply until all installation work has been properly carried out. The guidance given in the “first installation” se...

  • Page 25: First Installation

    25 first installation the following display appears: press the (green) button to move to the next menu. Use the buttons to select whether to replace the factory pre-programmed channel list by a pre-sorted channel list for a specifi c country (at present only a limited number of pre-sorted channel li...

  • Page 26: First Installation

    26 first installation system use the buttons here at “system” to select “cap”. Then use the buttons to select the “initialize cap” line and press the button to confi rm. Show 4:3 event here you can select the type of screen display mode for 4:3 broadcasts on a 16:9 tv set: - normal (pillarbox) - str...

  • Page 27: First Installation

    27 hds 900 first installation local time offset (utc) here you can use the buttons to select the local time offset to utc (formerly gmt) (e.G. For germany: + 1 hour). You can set the offset in 1 hour steps. The maximum offset is 12 hours (+ and -). Automatic clock change (summer/winter time) use the...

  • Page 28

    28 hds 900 xxx cap menu (turntable antenna settings) press the (green) button. The following display appears: use the buttons to select the “antenna confi guration” line and press the button to confi rm. The following display appears: you can also call up this menu via the main menu “settings”, “ant...

  • Page 29

    29 this function should be used only by experienced users. Exact knowledge of the satellite position and your present location are necessary when aligning the antenna manually to a satellite. Watch out for any obstacles that the antenna might collide with. The antenna is liable to be damaged by such...

  • Page 30

    30 cap menu (turntable antenna settings) using the numeric keys and/or the buttons, input the desired elevation value. Two seconds after completion of the input or when the button is pressed, the cap moves to the selected position. Elevation this function is not available. Lnb tilt/skew use the butt...

  • Page 31

    31 this menu allows important basic settings for the cap, such as the elevation border or elevation offset to be set. These two settings in particular should be performed by a specialist to match your needs and the conditions; if they are set incorrectly the cap may be damaged! Use the buttons to se...

  • Page 32: Alignment (Satellite Search)

    32 if the vehicle is not on supports during the search process and people are moving around inside it, there is a risk that movement of the vehicle will mean that the satellite is not found. Alignment (satellite search) the antenna is aligned automatically. After the ufs 940sw has been switched on, ...

  • Page 33

    33 channel (satellite) selection/programming the timer providing you are not in a menu, pressing the button calls up the channel list. The following display appears: by pressing the buttons all channels can be selected in the sequence that they appear in the current channel list and its sorting. Pre...

  • Page 34

    34 timer programming to prevent the turntable rotating at a time when it is unsupervised or when rotation might be irritating (e.G. In the middle of the night), a timer can be set. During the timer period the turntable is active only if the ufs 940sw is in operation or is in standby mode. If the rec...

  • Page 35: Change of Location

    35 after a change of location, the antenna moves to the last position selected. After initialisation, you will therefore see the following display (example, as it depends on the last selected position): for slight changes of location, the antenna can fi nd the satellite very quickly. If the search i...

  • Page 36: Park

    36 you have four options for “parking” the antenna. 1. The antenna can be moved to park position by pressing the button twice. 2. Press the (green) button. Use the buttons to select the “move cap to park position” line and press the button to confi rm. 3. Press the button to return to the main menu....

  • Page 37

    37 special messages from the turntable the following messages are shown on the screen to protect your reception system and the on-board power supply: system protection messages the power supply to the turntable is inadequate (battery voltage below the minimum value). The turntable can still be moved...

  • Page 38

    38 the vehicle ignition was switched on. For safety reasons, the turntable moves into the park position. This operates however only if the green ignition cable for the turntable is connected to the vehicle ignition and the turntable is connected to the power supply! As long as voltage is present at ...

  • Page 39

    39 special messages from the turntable a serious software error has occurred. Reset the turntable in the cap menu, or contact our service centre. Messages arising from software problems the turntable antenna software is defective. An update is required. Contact our service centre. The connection to ...

  • Page 40

    40 special messages from the turntable the satellite you have selected cannot be received from your current location, or there may have been changes made using the “cap settings” menu (see section “cap menu (turntable antenna settings), cap settings”), as a result of which the desired satellite cann...

  • Page 41: Disposal Instructions

    41 disposal instructions electronic equipment is not domestic waste - in accordance with directive 2002/96/ec of the european parliament and the council dated 27 th january 2003 on used electrical and electronic appliances, it must be disposed of properly. At the end of its service life, take this d...

  • Page 42: For Your Notes

    42 for your notes.

  • Page 43: For Your Notes

    43 for your notes.

  • Page 44

    Internet: www.Kathrein.De kathrein-werke kg • anton-kathrein-straße 1 - 3 • p.O. Box 100 444 • 83004 rosenheim • germany • phone +49 8031 184-0 • fax +49 8031 184-385 936.4245/-/zwt/0811/e - technical data subject to change..