1. DL manuals
  2. Kathrein
  3. Receiver
  4. MobiSet 2 CAP 210
  5. Installation Manual

Kathrein MobiSet 2 CAP 210 Installation Manual

Manual is about: Kathrein Satellite Receiver Installation Manual

Summary of MobiSet 2 CAP 210

  • Page 1

    Installation manual mobiset 2 digital cap 210 and mobi set 3 digital cap 310

  • Page 2

    2 important information about mobiset 2 digital cap 210 information for owners of mobiset 2 digital cap 210! The htv 115 lcd/tft television set is only included with the cap 310! If you have purchased a cap 210, all safety instructions, installation and operating steps and instructions outlined in t...

  • Page 3

    3 foreign language installation instructions electronic equipment is not household waste in accordance with directive 2002/96/ec of the european parliament and the council dated 27 th january 2003 on used electrical and electronic equipment, it must be disposed of properly. At the end of its service...

  • Page 4

    4 1. Roof duct with mounting nut 2. Mounting plate 3. Turntable 4. Antenna boom 5. Bas 60 hdp 171 ufd 170 for an explanation of the connections, see the “connection examples” section and operating manual ufd 170. Components of mobiset 3 digital cap 310 htv 115 for an explanation of the connections, ...

  • Page 5: Product Package

    5 • turntable with fi tted bas 60 and ready for connection cables with a length of 3.5 m • power supply cable (10 m) for connection to on-board network • mounting plate • roof duct with sealing gasket • sikafl ex® 291 sealing glue (100 ml tube) • ufd 170 satellite combi receiver with connecting cabl...

  • Page 6: Proper Use

    6 proper use the mobiset 3 digital cap 310 is designed to receive digital tv and radio programs via satellite. The turntable is intended for the kathrein planar antenna bas 60. This antenna can be used to receive digital tv and radio signals in the frequency range from 10.70 to 12.75 ghz; the antenn...

  • Page 7

    7 safety instructions - important notes when carrying out installation work in locations with a risk of falling, take appropriate safety precautions, e.G. Use of a working platform. Make sure that the vehicle roof is suffi ciently strong and stable to carry out the installation work (risk of damage ...

  • Page 8

    8 fundamental information a crucial safety factor is proper performance of installation and electrical connection work, and the specifi ed alignment of the turntable in the direction of travel (park position), see also installation and connection. Heed as precisely as possible the installation condi...

  • Page 9

    9 operate the system from your vehicle‘s battery (12 v) or a suitable mains power pack. This mains power pack must guarantee a stable initial voltage of 12 v, 11 a continuous current and 15 a (300 ms) surge current. The transient power consumption is up to a maximum of 12 a. To ensure reliable funct...

  • Page 10

    10 safety instructions - important notes instructions for installation and operation of the hdp 171 with the ufd 170 1. The turntable can only be used in conjunction with a kathrein ufd 170 caravan digital combi receiver or a kathrein ufd 540 caravan digital receiver with hds 160 control unit. 2. To...

  • Page 11

    11 safety instructions - important notes 3. Connecting the power supply cable lead marked “ignition” activates the turntable function for automatic lowering of the antenna. This lowering takes place as soon as the vehicle ignition circuit is turned on. When connecting the control unit to the on-boar...

  • Page 12: Installation and Connection

    12 installation and connection required tools and equipment • circular cutter, Ø 38 mm • flat-bladed screwdriver for m5 screws • drilling machine • galvanised tallow drop screws, depending on roof structure (Ø: 5 mm, sheet metal screws d 7981, depending on roof panel structure) or tallow drop screws...

  • Page 13: Installation and Connection

    13 • to ensure secure adhesion, the height difference of the roof curve may not be more than 1 cm over a length of 2 m, as otherwise the gap between the roof and the mounting plate would be too big to be fi lled by the sealing glue. • as the vehicle is constantly subjected to vibration loads during ...

  • Page 14: Installation and Connection

    14 installation and connection installation steps installation of cable duct and mounting plate note: if you have previously used a kathrein hdm140/141 fl exible satellite mast or another mast with a diameter of 34 mm, you can continue using the existing duct hole in the roof (if space allows). • in...

  • Page 15: Installation and Connection

    15 installation and connection • for very thin roof panel materials and insuffi cient support in the insulating material, through holes (Ø: 5.5 mm) into the interior of the vehicle are necessary and galvanised m5 tallow drop screws of suffi cient length should be used. Make sure that you use a suffi...

  • Page 16: Installation and Connection

    16 installation and connection figure: d • note before starting glueing work that the optimal processing temperature of materials to be glued and the sealing glue is between +15 °c und +25 °c. Prepare all necessary fastening elements and tools. • prepare the tube of sealing glue in accordance with t...

  • Page 17: Installation and Connection

    17 installation and connection installation of turntable version with cable duct below turntable (fig. E) • check that the o ring is correctly positioned in the groove of the cable duct (fig. A). An incorrectly positioned or missing o ring will allow water to penetrate. • feed the ends of the cables...

  • Page 18: Installation and Connection

    18 installation and connection version with external cable duct (fig. F) • arrange the cables in the cable duct when placing the turntable onto the mounting plate. Make sure that the cables are not crossed over and that they are tightened so that they cannot be kinked. Do not try to pull the cable o...

  • Page 19: Installation and Connection

    19 installation and connection brief instructions for installing the hdp 171 the sequence of pictures shown illustrates all the necessary installation steps that are required to assemble the hdp 171 turntable and the bas 60 planar antenna on the roof of the vehicle. The other detailed instructions i...

  • Page 20: Installation and Connection

    20 set up electrical connections. Connect ufd 170/ufd 540 receiver. Connect connecting/control unit to battery. Installation and connection the antenna must always be lowered into horizontal position (park position) while driving! Maximum driving speed of the vehicle: 130 km/h installation of ufd 17...

  • Page 21: Installation and Connection

    21 installation and connection laying cables and connecting the turntable hdp 171 • lay the control cable (8-pole western connector), the coaxial cable and the power supply cable (2-pole connector) to the ufd 170. Avoid laying the cables across sharp edges and secure the cable against possible abras...

  • Page 22: Installation and Connection

    22 installation and connection connecting the htv 115 lcd tv set connect a htv 115 and the receiver with the included cinch/cinch cable included with the ufd 170. Make sure that you heed the colour identifi cation of the connectors and outlets on the back side of the receiver. Connect the tv with th...

  • Page 23: Installation and Connection

    23 connection example motorhome - 12 v battery connection (ufd 170) installation and connection attention: for operation with two batteries, it must be ensured that the ignition signal earth has the same potential as the power supply battery earth for the ufd 170 combi receiver. Non-compliance means...

  • Page 24: Installation and Connection

    24 connection example caravan - 230 v battery connection (ufd 170) installation and connection fig: h 8-pole 6-pole brown white green note! Do not connect. Option not available. The antenna must be lowered before departure. • turn on receiver • select hdp menu • select park function and confirm main...

  • Page 25: Bas 60 Planar Antenna

    25 bas 60 planar antenna proper use the bas 60 fl at antenna is used to receive digital tv and radio signals in the frequency range from 10.70 to 12.75 ghz. It cannot receive terrestrial signals. The bas 60 has been designed for mobile use, to receive satellite signals in stationary caravans, motorh...

  • Page 26: Bas 60 Planar Antenna

    26 bas 60 planar antenna the footprint is the reception area on the earth that a satellite covers with its transmission beam (spot), within which satellite reception is possible. The transmission power is at its greatest in the centre of this spot – it becomes progressively weaker moving outwards. Y...

  • Page 27: Polarisation Setting

    27 polarisation setting polarisation setting as supplied, the bas 60 is mounted centrally on the turntable. In this position, you can also receive signals from satellites with deviations in the degree of longitude (of the typical reception range) of between 15° and 20° from the orbit position of the...

  • Page 28: Polarisation Setting

    28 we strongly advise that users who are not familiar with the installation work should not reassemble the bas 60 independently. They should contact a technician or engineer. They may fi nd a suitable person on the campsite. Make sure that: - the antenna and connected units are disconnected from the...

  • Page 29: Polarisation Setting

    29 polarisation setting to dismantle/install the planar antenna from the turntable, proceed as follows: (the key names refer to the remote control for the ufd 170 receiver) 1. Turn on the receiver with the main switch on the front of the unit. 2. Press the standby button ( ) to start up the receiver...

  • Page 30: Installation and Connection

    30 view after installation +15° view after installation in the middle (standard) view after installation -15° installation and connection.

  • Page 31: Dismantling For Servicing

    31 dismantling for servicing if repairs to the system or individual components are necessary, contact your specialist dealer or our service centre (see below for address). Never open the turntable yourself! Dismantling • the cables may not be cut! • disconnect the power, coaxial and data cables from...

  • Page 32: Technical Data

    32 technical data dimensions (mm) driving direction.

  • Page 33: Technical Data

    33 technical data electric data supply voltage 10.9…13.8 v ignition signal 12…24 v “standby” current 20 ma “engine on” current 5...8 a transient start-up current 12 a azimuth rotation range 0…370° elevation rotation range 10…90° search time for fi rst satellite (typ.) 10…120 s search time for additi...

  • Page 34: Sikafl Ex

    34 sikafl ex ® 291 data sheet.

  • Page 35: Sikafl Ex

    35 sikafl ex ® 291 technical data sheet.

  • Page 36: Declaration of Conformity

    Declaration of conformity 936.2712/b/0306/zwt - technical data subject to change. Internet: www.Kathrein.De kathrein-werke kg • anton-kathrein-strasse 1 - 3 p.O. Box 100 444 • 83004 rosenheim germany.