1. DL manuals
  2. Kathrein
  3. Antenna
  4. MobiSet 3 Digital CAP 700
  5. Installation And Operating Manual

Kathrein MobiSet 3 Digital CAP 700 Installation And Operating Manual

Manual is about: Kathrein Turntable Installation and Operating Manual

Summary of MobiSet 3 Digital CAP 700

  • Page 1

    Installation and operating manual mobiset 3 digital cap 700

  • Page 2: Contents

    2 contents ............................................................................................................................... 2 foreign language installation manuals/disposal .................................................... 3 mobiset 3 cap 700 components/scope of delivery .............

  • Page 3

    3 dear customer, chère cliente, cher client, gentile cliente, estimado cliente, gb you can obtain an english version of our mounting instructions from our representatives in your country (http://www.Kathrein.De/include/kontakte_groups_eng.Cfm?Kontinent=1&gruppe=sat) or download one from our homepage...

  • Page 4

    4 mobiset 3 cap 700 components/scope of delivery ufs 740sw (front view) the mobiset 3 digital cap 700 consists of: • turntable complete with control electronics, pre-assembled parabolic refl ector with lnb • mounting plate • complete cabling set: 1 x coax cable 8 m long, and one power supply cable (...

  • Page 5: Proper Use

    5 proper use the mobiset 3 digital cap 700 is designed to receive digital tv and radio programs via satellite. The automatic positioner is intended to be used as a turntable for the parabolic refl ector. The turntable can be used to receive digital tv and radio signals in the frequency range from 10...

  • Page 6

    6 safety instructions - important notes safety during installation work when carrying out installation work in locations where there is a risk of falling, take appropriate safety precautions, e.G. Use of a working platform. Make sure that the vehicle roof is suffi ciently strong and stable to carry ...

  • Page 7

    7 road traffi c licensing regulations (stvzo) the applicable regulations of the stvzo must be observed in respect of fi xed installation of the turntable on a vehicle which is driven on public highways. In particular, §§ 19/2; 30 c; 32 (2) and the ec directive 74/483 eec are applicable. Briefl y, th...

  • Page 8

    8 safety precautions during operation during operation of the turntable, make sure that no persons, in particular children, are in the immediate vicinity of the turntable and that they cannot touch any moving parts – crush hazard! Always unplug the power supply during installation work. The antenna ...

  • Page 9: Installation And Connection

    9 • circular cutter, Ø 38 mm • flat-bladed screwdriver for m5 screws • power drill • galvanised round head screws, depending on the roof structure (Ø: 5 mm, sheet metal screws d 7981, depending on the roof structure) or round head screws d 7985 with washers and nuts • twist drill, Ø 2.5 or 5.5 mm • ...

  • Page 10: Installation And Connection

    10 • when selecting the installation position, take into account the range of movement of the turntable (see graphics and the “technical data” chapter). There must be no structures on the roof that would obstruct this range of movement (risk of collision). For safety, keep at least the required area...

  • Page 11: Installation And Connection

    11 • choose an installation position on the roof that is as horizontal as possible or only slightly sloping, depending on the location of the vehicle, since roof inclinations greater than 5° may lead to problems when searching for the satellite. • to ensure secure adhesion, the height difference of ...

  • Page 12: Installation And Connection

    12 • mark out the positions of the six fastening holes on the roof of the vehicle in a circular pattern. Note: the size of the holes and the choice of fastening screws to be used (not supplied) depend on the type and thickness of the materials used in the roof structure. If the roof panelling (plast...

  • Page 13: Installation And Connection

    13 • create the holes necessary to secure the mounting plate (fig. C). • in addition to the screwed connection, the mounting plate and roof gland must be bonded to the roof with adhesive and sealed. This is done using the sikafl ex® 291 adhesive sealant supplied, which is ideally suited for this pur...

  • Page 14: Installation And Connection

    14 • ensure before starting adhesive work that the temperature of materials to be glued and the adhesive sealant is between +5 °c and +40 °c. Prepare all necessary fasteners and tools. • prepare the tube of adhesive sealant in accordance with the instructions enclosed with the tube. • remove the roo...

  • Page 15: Installation And Connection

    15 figure: e installation and connection • lift up the turntable and place it carefully on the mounting plate facing in the direction of travel (see illustration fig. E) (do not step on the plug connector and do not kink/crush the cables!) the through holes on the turntable must be perfectly aligned...

  • Page 16: Installation And Connection

    16 installation and connection version with external cable gland (fig. F) • the external roof gland is arranged so that it forms a water-tight enclosure on the vehicle roof around the point where the two cables projecting from the turntable are connected to the two extension cables within the interi...

  • Page 17: Installation And Connection

    17 installation and connection brief instructions for installing the turntable the sequence of pictures shown illustrates all the necessary installation steps that are required to install the turntable and the bas 60 parabolic refl ector on the roof of the vehicle. The other detailed instructions in...

  • Page 18

    18 avoid skin contact! Arrow in the direction of travel. Mark out the six holes for securing the mounting plate. Apply sikafl ex® 291 adhesive in a sinuous line between the two grooves and spread with spatula or similar. Avoid skin contact! Place mounting plate on roof gland and secure with appropri...

  • Page 19: Installation And Connection

    19 installation and connection the turntable is controlled by the ufs 740sw dvb-s receiver. The cable lengths must be taken into account when choosing the installation location. For suspended installation use the installation kit supplied with the receiver. Note: when choosing the installation locat...

  • Page 20: Installation And Connection

    20 remove the wood screws supplied from their transport attachment on the underside of the respective mounting piece (2 pieces). Vertically insert each mounting piece into the fi fth slot from the edge, as shown in fig. 1. Then push each mounting piece downwards and outwards (see fig. 2) until they ...

  • Page 21: Installation And Connection

    21 installation and connection • lay the coaxial cable to the ufs 740sw. • lay the turntable power supply cable (3-pin plug) to the battery. Avoid laying the cables across sharp edges and protect the cables against possible chafi ng points. • connect the coaxial cable (coming from the turntable) to ...

  • Page 22: Installation And Connection

    22 installation and connection under certain circumstances, problems can arise when the units are connected to different connecting sockets or circuits/earth potentials. If no others are available, it is recommended that you connect the connecting sockets for receiver and tv set to the same cable, a...

  • Page 23: Installation And Connection

    23 important: for operation with two batteries, it must be ensured that the ignition signal earth has the same potential as the power supply battery earth for the turntable. Non-compliance means that the automatic lowering function will not work! Ensure the cable polarity is correct! Figure: g insta...

  • Page 24: Reception Range/footprint

    24 reception range/footprint the footprint is the reception area on the earth that a satellite covers with its transmission beam (spot), within which satellite reception is possible. The transmission power is at its greatest in the centre of this spot – it becomes progressively weaker moving outward...

  • Page 25: Esc

    25 if repairs to the system or individual components are necessary, contact your specialist dealer or our service centre (see below for address). Never open the turntable yourself! • do not cut the cables! At the cable junction provided, disconnect the cables projecting from the turntable from the t...

  • Page 26: Polarisation Setting

    26 polarisation setting the lnb for the cap 700 is factory-set to the polarisation setting “0”. In this position you can still receive signals from satellites with differences (between the longitude of the desired reception area and the orbit position of the satellite) of 15° to 20°. For differences...

  • Page 27

    27 satelliten/ satellites /satellites land/ country /pays tÜrksa t 42° ost east /est astra (eurobird 1) 28.2° ost east /est astra 19.2° ost east /est eutelsa t w2 16° ost east /est hotbird 13° ost east /est eutelsa t w1 10° ost east /est eutelsa t w3a 7° ost east /est thor 2/3 0.8° we s t we s t /ou...

  • Page 28: Polarisation Setting

    28 polarisation setting safety notes we strongly advise that users who are not familiar with the setting operations should not undertake to set the lnb themselves. They should contact a technician or engineer. They may fi nd a suitable person on the campsite. Make sure that: - the antenna and connec...

  • Page 29: Polarisation Setting

    29 polarisation setting 8. Press the button and the turntable will move to the selected elevation angle. 9. Turn off the ufs 740 using the main switch on the front and disconnect it from the power. 10. Use the socket driver supplied (size 20) to slacken the securing screw of the clamp on the lnb. 11...

  • Page 30

    30 if a defect arises in the electronic controls, after some disassembly work the satellite dish can be returned to the park position (horizontal position) manually. Following this however recalibration by an authorised workshop is always necessary. Driving to the nearest workshop with the antenna e...

  • Page 31

    31 manual lowering to park position manual lowering 1. In the centre of the antenna (arrowed) there is a plastic cap. Lever this off with a narrow slot-head screwdriver. 2. Behind the cap is an m8 hexagon head screw. Unscrew these using a 13 mm socket wrench. After removing the m8 screw, a further t...

  • Page 32: Technical Data

    32 technical data dimensions (mm) direction of travel mounting plate.

  • Page 33: Technical Data

    33 technical data elevation max. 75° elevation 45° rotary axis mounting plate clamping range 20/50 roof gland nut 137.5 including mounting plate.

  • Page 34: Technical Data

    34 technical data ignition signal 12…24 v search time for fi rst satellite (typ.) 10…120 s search time for further satellites (typ.) 2…30 s lsm search time 2…15 s (lsm = last satellite memory) type cap 700 order no. 20310019 lnb 1 output switchable: v/h (14/18 v), low/high (0/22 khz) lnb supply volt...

  • Page 35: Sikaflex

    35 sikaflex ® 291 safety data sheet 1. Materials/preparation and company designation data on the product (trade name): sikafl ex ® 291 data on manufacturer/suppliers manufacturer/suppliers: sika deutschland gmbh street/postcode: kornwestheimer str. 103-107 postcode and town: stuttgart country: germa...

  • Page 36: Sikaflex

    36 5. Measures for fi re fi ghting suitable extinguishing media compatible with all extinguishing media in general use. Special hazard from the product, its products of combustion or gases released in case of fi re the following can be released: carbon monoxide (co) carbon dioxide (co 2 ) hydrogen c...

  • Page 37: Sikaflex

    37 4,4‘ methylene-diphenyl-diisocyanate 101-68-8 permissible workplace concentration 0.05 mg/m 3 trgs 900/de/2004 101-68-8 permissible workplace concentration 0.005 ml/m 3 trgs 900/de/2004 xylol 1330-20-7 permissible workplace concentration 440 mg/m 3 trgs 900/de/2004 1330-20-7 permissible workplace...

  • Page 38: Sikaflex

    38 11. Toxicology data sensitisation sensitisation/allergic reactions may occur. Sensitive individuals may exhibit allergic reactions even at very low concentrations. Experience of human exposure on skin contact: may lead to irritation on eye contact: may lead to irritation on being breathed in: may...

  • Page 39: Sikaflex

    39 risk phrases 42 sensitisation possible by breathing in. Safety phrases 23 do not breathe in gas/smoke/vapour/aerosol. 45 in the event of accident or feeling unwell summon a doctor immediately (if possible show the doctor this label). Special identifi cation of particular components contains isocy...

  • Page 40: Sikaflex

    40 sikaflex ® 291 technical data sheet si kafle x ® -291 1 / 2 technisches merkblatt version 12 / 2005 sikaflex ® -291 der haftstarke marine-dichtstoff technische eigenschaften chemische basis 1-k polyurethan farbe weiss, schwarz, holz härtungsmechanismus feuchtigkeitshärtend dichte vor aushärtung (...

  • Page 41: Sikaflex

    41 sikaflex ® 291 technical data sheet si kafle x ® -291 2 / 2 weitere informationen internet: www.Sika-industry.De, e-mail: industry@de.Sika.Com www.Sika.Com sika deutschland gmbh kleb- und dichtstoffe industrie stuttgarter strasse 139 d-72574 bad urach deutschland tel. +49 7125 940-761 fax +49 712...

  • Page 42: Cap 700 Operating Manual

    42 cap 700 operating manual the operating manual for the cap 700 if, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly, or if unexpected problems occur, please contact your specialist dealer. The kathrein customer hotline is al...

  • Page 43

    43 so as to avoid overheating the turntable motors, do not operate the motors continuously for longer than 10 minutes. None of the search procedures initiated by the cap 700 will require as much as 10 minutes operation. Only repeated unsuccessful search procedures or manual overrides by the user can...

  • Page 44: First Installation

    44 first installation before using your unit for the fi rst time, read the “safety instructions - important information” and “installation and connection” sections. You will fi nd a sample confi guration for a motor home in the section “installation and connection”, “connection example”. Do not conn...

  • Page 45

    45 the following display appears: use the buttons to select whether to replace the default channel list with one pre-sorted for germany, austria, switzerland or italy. If you want to use the default channel list, choose “no” under “restore channellist”. Press the ! (green) button to move to the next...

  • Page 46: First Installation

    46 first installation system use the buttons at “system” to select “cap”. Then press the ! (green) button to move to the next menu. Tv aspect ratio select the tv's picture format. Either 4:3 or 16:9 picture format here you select the type of screen display, depending on the setting of your tv format...

  • Page 47: First Installation

    47 first installation local time offset use the buttons to set the time zone variation from utc (formerly gmt) (e.G. For germany +1 hour). Use the buttons to switch to the “automatic clock change” fi eld. Use the buttons to select whether the receiver should automatically change over between summer ...

  • Page 48: Alignment (Satellite Search)

    48 alignment (satellite search) the antenna is aligned automatically. After the ufs 740 has been switched on, the turntable automatically moves to the last channel received and the associated satellite position (e.G. Ard/astra). This works because each satellite is automatically recognised by the tu...

  • Page 49

    49 press the button to return to the main menu. The buttons and button allow you to call up the submenus (“settings”, “antenna confi guration”). You can correct the inclination and horizontal angle of the antenna using the “elevation” and “azimuth” settings. To do this press the buttons or enter a n...

  • Page 50

    50 channel (satellite) selection providing you are not in a menu, pressing the button calls up the channel list. The following display appears: by pressing the & buttons all channels can be selected in the sequence that they appear in the current channel list and its sorting. Press the # (blue) butt...

  • Page 51

    51 if you still want to aim at the satellite, press the button to start the search. After a change of location, the antenna moves to the last position selected. After initialisation, you will therefore see the following display (example, as it depends on the last selected position): if a signal is f...

  • Page 52: Reset/parking

    52 reset/parking use the buttons to navigate to the sub-item “reset the turn table antenna” and then press the button. The following display appears: press the button to acknowledge the displayed message. The antenna is reset and automatically moves to park position. A further short message “park po...

  • Page 53: Reset/parking

    53 you have three options for “parking” the antenna. 1. The antenna can be moved to park position by pressing the button twice. 2. Press the button to return to the main menu. The buttons and button allow you to call up the submenus (“settings”, “antenna confi guration”). Use the buttons to navigate...

  • Page 54

    54 special messages from the turntable the following messages are shown on the screen to protect your reception system and the on-board power supply: system protection messages the power supply to the turntable is inadequate (battery voltage below the minimum value). The turntable can still be moved...

  • Page 55

    55 the vehicle ignition was switched on. For safety reasons, the turntable moves into the park position. This operates however only if the green ignition cable for the turntable is connected to the vehicle ignition and the turntable is connected to the power supply! As long as voltage is present at ...

  • Page 56

    56 special messages from the turntable a serious software error has occurred. Reset the turntable in the cap menu, or contact our service centre. Messages arising from software problems the turn table antenna software is defective. An update is required. Contact our service centre..

  • Page 57

    57 special messages from the turntable the connection to the turntable is defective. Reset the turntable in the cap menu, check the connections between the turntable and receiver, or contact our service centre. The receiver has lost communication with the turntable. Check the connection between the ...

  • Page 58: Declaration of Conformity

    Declaration of conformity ec declaration of conformity rosenheim, 04.07.07.

  • Page 59: For Your Notes

    59 for your notes.

  • Page 60

    Internet: http://www.Kathrein.De kathrein-werke kg • anton-kathrein-straße 1 - 3 p.O. Box 100 444 • 83004 rosenheim germany 936.3417/-/0908/zwt - t echnical data subject to change..