1. DL manuals
  2. Kathrein
  3. Home Cinema speakers
  4. MobiSet 4 digital CAP 900
  5. Installation And Operating Manual

Kathrein MobiSet 4 digital CAP 900 Installation And Operating Manual

Manual is about: Kathrein MobiSet 4 digital CAP 900 Installation and operating manual

Summary of MobiSet 4 digital CAP 900

  • Page 1

    Installation and operating manual - englisch - mobiset 4 digital cap 900

  • Page 2: Contents

    2 contents contents ............................................................................................................................... 2 foreign language installation manual / disposal .................................................... 3 mobiset 4 cap 900 components / scope of deliver...

  • Page 3

    3 dear customer, chère cliente, cher client, gentile cliente, estimado cliente, gb you can obtain an english version of our installation instructions from our representatives in your country (http://www.Kathrein.De/include/kontakte_groups_eng.Cfm?Kontinent=1&gruppe=sat) or download one from our home...

  • Page 4

    4 mobiset 4 cap 900 components / scope of delivery 75 cm satellite dish twin lnb turntable with integral controls and gps receiver ufs 740sw (front view) the mobiset 4 digital cap 900 consists of: • turntable complete with control electronics (and gps receiver), pre-assembled satellite dish and twin...

  • Page 5: Proper Use

    5 proper use the mobiset 4 digital cap 900 is designed to receive digital tv and radio programs via satellite. The automatic positioner is intended to be used as a turntable for the kathrein satellite dish. The turntable can be used to receive digital tv and radio signals in the frequency range from...

  • Page 6

    6 safety instructions - important notes safety during installation work when carrying out installation work in locations where there is a risk of falling, take appropriate safety precautions, e.G. Use of a working platform. Make sure that the vehicle roof is suffi ciently strong and stable to carry ...

  • Page 7

    7 safety instructions - important notes road traffi c licensing regulations (stvzo) the applicable regulations of the stvzo must be observed in respect of fi xed installation of the turntable on a vehicle which is driven on public highways. In particular, this applies to §§ 19/2; 30 c; 32 (2) and th...

  • Page 8

    8 safety instructions - important notes checks before commencing a journey • before commencing a journey, the antenna must always be lowered into horizontal position (park position). If the antenna collides with a fi xed or moving object, you must check that it is still securely attached. • as the a...

  • Page 9: Installation And Connection

    9 • circular cutter, Ø 38 mm • flat-bladed screwdriver for m5 screws • drilling machine • galvanised raised head screws, depending on roof structure (Ø: 5 mm, sheet metal screws d 7981, depending on roof panel structure) or raised head screws d 7985 with shims and nuts • twist drill, Ø 2.5 or 5.5 mm...

  • Page 10: Installation And Connection

    10 • when selecting the installation position, take into account the range of movement of the turntable (see the grey shaded area in the graphics). Within this grey area there must be no structures on the roof that would obstruct this movement (risk of collision). For safety, keep at least the requi...

  • Page 11: Installation And Connection

    11 • in the centre of the intended position of the turntable, drill the opening for the cable gland with a circular cutter (Ø: 38 mm). Deburr the hole with a round fi le or emery paper. • provisionally insert the roof gland into the drilled hole (fig. A). • place the mounting plate on the roof of th...

  • Page 12: Installation And Connection

    12 • for very thin roof panel materials and insuffi cient purchase in the insulating material, through holes (Ø: 5.5 mm) into the interior of the vehicle are necessary; galvanised m5 raised head screws of suffi cient length should then be used. Make sure that you use a suffi ciently strong support t...

  • Page 13: Installation And Connection

    13 • before starting adhesive work, note that the optimum processing temperature of materials to be glued and the adhesive sealant is between +15 °c und +25 °c. Prepare all necessary fastening elements and tools. • prepare the tube of adhesive sealant in accordance with the instructions enclosed wit...

  • Page 14: Installation And Connection

    14 figure: e1 installation and connection figure: e2 master coaxial cable (marked red) • lift up the turntable and place it carefully on the mounting plate facing in the direction of travel (see illustrations fig. E) (do not step on the plug connector and do not kink/crush the cables!) the through h...

  • Page 15: Installation And Connection

    15 installation and connection version with external cable duct (fig. F) • lay the cables supplied with the turntable (2 × coax cables and 1 x power supply cable) into the mounting plate as indicated by the markings on the mounting plate (see illustrations fig. F), and feed the remaining lengths of ...

  • Page 16: Installation And Connection

    16 installation and connection the turntable is controlled by the ufs 740sw dvb-s receiver. The cable lengths must be taken into account when choosing the installation location. For suspended installation use the mounting kit supplied with the receiver. Note: when choosing the installation location,...

  • Page 17: Installation And Connection

    17 remove the wood screws supplied from their transport attachment on the underside of the respective mounting piece (2 pieces). Vertically insert each mounting piece into the fi fth slot from the edge, as shown in fig. 1. Then push each mounting piece downwards and outwards (see fig. 2) until they ...

  • Page 18: Installation And Connection

    18 installation and connection • lay the master coaxial cable (marked red) to the ufs 740sw and the second coaxial cable to the second receiver. If you are not using a second receiver, we recommend that you lay the second coaxial cable in any case, so that it is available should you ever need it. • ...

  • Page 19: Installation And Connection

    19 installation and connection under certain circumstances, problems can arise when the units are connected to different connecting sockets or circuits/earth potentials. If none are available, it is recommended as depicted in figure “h” that you connect the connecting sockets for receiver and tv set...

  • Page 20: Installation And Connection

    20 important: for operation with two batteries, it must be ensured that the ignition signal earth has the same potential as the power supply battery earth for the turntable. Non-compliance means that the automatic lowering function will not work! Figure: g installation and connection connection exam...

  • Page 21: Reception Range / Footprint

    21 reception range / footprint the footprint is the reception area on the earth that a satellite covers with its transmission beam (spot), within which satellite reception is possible. The transmission power is at its greatest in the centre of this spot – it becomes progressively weaker moving outwa...

  • Page 22: Esc

    22 if repairs to the system or individual components are necessary, contact your specialist dealer or our service centre (see below for address). Never open the turntable yourself! • the cables may not be cut! Disconnect the cables at the cable disconnection box provided for the purpose • cables lai...

  • Page 23

    23 if a defect arises in the electronic controls, after some disassembly work the satellite dish can be returned to the park position (horizontal position) manually. Following this however recalibration by an authorised workshop is always necessary. Driving to the nearest workshop with the antenna e...

  • Page 24

    24 1. In the centre of the antenna (arrowed) there are two plastic caps, one to the left and one to the right. Lever them off with a narrow fl at-bladed screwdriver. 2. Behind each cap is an m8 hexagon head screw. Unscrew these using a 13 mm socket wrench. Once the m8 screws have been removed, a fur...

  • Page 25: Technical Data

    25 technical data type cap 900 order no. 20310012 lnb 2 outputs switchable: v/h (14/18 v), low/high (0/22 khz) lnb supply voltage v vert.: 11.5-14, horiz.: 16-19 input frequency ghz 10.70-12.75 output frequency mhz 950-1950/1100-2150 oscillator frequency (l.O.) ghz 9.75/10.60 system quality (g/t) 11...

  • Page 26: Sikaflex

    26 sikaflex ® 291 data sheet.

  • Page 27: Sikaflex

    27 sikaflex ® 291 technical datasheet.

  • Page 28: Cap 900 Operating Manual

    28 cap 900 operating manual the operating manual for the cap 900 starts on this page if, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly, or if unexpected problems occur, please contact your specialist dealer. The automatic u...

  • Page 29

    29 all settings on the ufs 740 are made using the remote! Important information for cap 900 before setup this section of the ufs 170 operating manual for the turntable assumes that the ufs 170 and the turntable have been properly installed and connected, as described in the installation and operatin...

  • Page 30: First Installation

    30 first installation before using your unit for the fi rst time, read the “safety instructions – important information” and “installation and connection” sections. In the “installation and connection” section you will fi nd a sample confi guration (one for a motor home and one for a caravan). Do no...

  • Page 31: First Installation

    31 first installation use the buttons here to select the settings for your tv set. When doing this, refer to the operating instructions for your tv set! Tv format select the tv‘s picture format. Either 4:3 or 16:9 screen display here you select the type of screen display, depending on the setting of...

  • Page 32: First Installation

    32 first installation system use the buttons at “system” to select “cap 900”. Then press the ! (green) button (channel scan “item 4/5” is skipped). The following display appears: set local time use the buttons to set the time zone variation from utc (formerly gmt) (e.G. For germany +1 hour). Use the...

  • Page 33: Alignment (Satellite Search)

    33 alignment (satellite search) the antenna is aligned automatically. After the ufs 740 has been switched on, the turntable automatically moves to the last channel received and the associated satellite position (e.G. Ard/astra). This works because every satellite broadcasts its own identifi cation s...

  • Page 34: Alignment (Satellite Search)

    34 at the margins of the footprints of a satellite (e.G. After a slight change of position), it may be necessary for you to manually correct the setting (not normally required). It is also possible to manually correct the fi ne tuning. Press the button to switch to the main menu. The buttons and but...

  • Page 35

    35 channel (satellite) selection providing you are not in a menu, pressing the button calls up the channel list. The following display appears: by pressing the & buttons all channels can be selected in the sequence that they appear in the current channel list and its sorting. Press the # (blue) butt...

  • Page 36

    36 if you still want to aim at the satellite, press the button to start the search. After a change of location, the antenna moves to the last position selected. After initialisation, you will therefore see the following display (example, as it depends on the last selected position): if a signal is f...

  • Page 37: Reset/parking

    37 reset/parking use the buttons to navigate to the sub-item “reset turntable antenna” and now press the button. The following display appears: press the button to confi rm the displayed message. The antenna is reset and automatically moves to park position. A further short message “park position re...

  • Page 38: Reset/parking

    38 you have three options for “parking” the antenna. 1. The antenna can be moved to park position by pressing the button twice. 2. Press the button to switch to the main menu. The buttons and button allow you to call up the submenus (“settings”, “antenna confi guration”). Use the buttons to navigate...

  • Page 39

    39 special messages from the turntable the following messages are shown on the screen to protect your reception system and the on-board power supply: system protection messages the power supply to the turntable is insuffi cient (battery voltage below minimum value). The turntable can still be moved,...

  • Page 40

    40 the turntable motor temperature is in the critical range. The controls can move the turntable only to a known satellite position or to the park position. In addition you receive the message “last move done” (to allow the turntable motor the opportunity to cool down, no movements of the turntable ...

  • Page 41

    41 a serious software error has occurred. Reset the turntable in the cap menu, or contact our service centre. The motorised antenna software is defective. An update is required. Contact our service centre. Special messages from the turntable messages arising from software problems the motorised ante...

  • Page 42

    42 this satellite is inaccessible from this gps position! Change to another satellite or change the location of your motor home or caravan. Special messages from the turntable the connection to the turntable is defective. Reset the turntable in the cap menu, check the connections between the turntab...

  • Page 43: Declaration of Conformity

    Declaration of conformity.

  • Page 44

    Internet: http://www.Kathrein.De kathrein-werke kg • anton-kathrein-straße 1 - 3 p.O. Box 100 444 • 83004 rosenheim germany 936.3084/a/0707/zwt - t echnical data subject to change..