Summary of MSK 200/S2
Page 1
User manual antenna signal meter system msk 200/s2.
Page 2: Preface/important Notes
2 preface/important notes dear customer, we kindly ask you to observe all instructions contained in this manual. The kathrein-werke kg has made every effort to ensure that the data and descriptions in this manual are accurate and complete. We reserve the right to make changes to this manual without ...
Page 3: Content
3 content preface/important notes ................................................................................................. 2 general safety information .......................................................................................... 2 content .........................................
Page 4: Safety
4 safety this device was built and tested in accordance with the enclosed eu certifi cate of conformity and left the factory in a condition fullfi lling all requisite safety regulations. To ensure that this condition is maintained and to ensure hazard-free operation, the user must observe all in- st...
Page 5: Safety
5 safety 5. Prior to switching on the device, ensure that the nominal mains voltage set on the device and the nominal mains voltage of the supply match. If it is necessary to change the voltage setting, it may also be necessary to change the respective mains fuse for the device. 6. In case of device...
Page 6: Features/delivery Scope
6 features/delivery scope the msk 200 is a compact state-of-the-art signal meter which leaves nothing to be desired when you are checking antenna and cable systems or even professional head-end systems. It can be used either in a lab or for the monitoring of remote-controlled head-end systems, or fo...
Page 7: Operation
7 operation initial start-up prior to operating for the fi rst time, please take the t 8.0 a fuse out of the packaging and fi t it into the provided fuse holder. The fuse prevents the device being switched on unintentionally during transport. Caution! Please remove this fuse again before shipping th...
Page 8: Operation
8 using the device on the shoulder strap when the device is used on the strap, also provide for adequate ventilation! To avoid a build up of heat, the openings for the fan and the ventilation holes must always be clear. Operation for right-handed users pass the shoulder strap over your right shoulde...
Page 9: General Operation
9 general operation keyboard operation settings: save, setup, copy, print switching the device on/off, or to standby mode. If the button is kept pressed more than 5 seconds, the device is switched off. Switching the softkeys on/off, zooming in the graphic display selecting sources: sat analogue, sat...
Page 10: General Operation
10 general operation touchscreen operation tap on the touchscreen keys to select the respective task! Sources selection (source) measurement selection (analyze) when the “source“ button is pressed, the source selection buttons appear, which can be used to select the signal path! When the “analyze” k...
Page 11: General Operation
11 general operation this type of key leads to a selection of various set- tings (e.G. Selection of the channel)! This type of key offers the facility for alphanumerical input (e.G.: entering programme names)! This type of key offers the facility for numerical input (e.G.: entering programme numbers...
Page 12: General Operation
12 general operation to open the zoom window, press and hold your fi n- ger on the marker; you can then shift it to the desired position! Press the “function“ key, tap on the screen and hold to drag the screen section as required (e.G.: the delay time on the oscilloscope, the mid-frequency on the sp...
Page 13: Operation
13 operation choice of the signal source and measurement the most important keys on the msk 200 are and . After activating the key, you will be able to defi ne the source and the channel or transponder to be measured. After pressing the key, you will be able to choose the type of measurement wanted ...
Page 14: Operation
14 operation choosing the channel to be measured now one can choose the channel to be measured: generally there are different possibilities offered as to how a measurement channel can be chosen 1. Selection of programme through programme name 1.1. Press “chan.Tab“ to select the desired channel table...
Page 15: Operation
15 operation information on the individual measurement possibilities can also be found in the on-board help menus. Generally an optimal pre-setting of parameters is saved in the msk 200 for each type of measurement. There are though many other set-up possibilities that can be carried out dependant o...
Page 16: Function Overview
16 function overview mains external ac power supply unit 100...240 v battery internal li-ion battery 12 v/6,5 ah external battery supply vehicle 11 v...16 vdc keyboard 12 hardkeys on/off, help, prog.+, prog.-, analyze, source, osd/off, vol.+, vol.-, copy, function, extend external keyboard ascii key...
Page 17: Function Overview
17 function overview tv (catv/terrestrial) 5...900 mhz satellite 900....3100 mhz fm 87,5...108 mhz spectrum analysis 5...3100 mhz digital catv j83 a/c (dvb-c) 16, 32, 64, 128 ,256 qam j83 b 64 qam docsis 64, 256 qam analogue catv pal, nicam b/g, i, d/k, l/l´, m/n ntsc, nicam b/g, i, d/k, l/l´, m/n s...
Page 18: Technical Appendix
18 technical appendix design • manageable portable signal meter • high-resolution 10.4“ tft colour display to graph analogue and digital tv signals and graphics • backlight - thus the display is excellently readable also in bright sunlight (typ. 600 cd/m 2 ) • easy operation using 12 hard keys and t...
Page 19: Technical Appendix
19 type msk 200/s2 msk 200/s2 order no. 21710024 21710025 spectrum analyser frequency range mhz 5-3100 resolution bandwidth (-3 db) mhz 0.001-10 resolution bandwidth (-6 db) khz 9, 25, 50, 120, 200 video bandwidths mhz 0.00001-3 phase noise at 10 khz carrier level spacing dbc phase noise at 100 khz ...
Page 20: Technical Appendix
20 technical appendix digital catv receiver (j83 a, b, c) modulation type 16 qam, 32 qam, 64 qam, 128 qam, 256 qam symbol frequency msymb/s 2.0-6.999 frequency increment khz 50 video output voltage/impedance v ss / Ω 1/75 ± 1 db if bandwidths mhz 1, 5, 6, 7, 8, 12 mer measurement db > 33/typ. 38 dig...
Page 21: Technical Appendix
21 technical appendix connections rf input standarad (impedance) Ω 1.6/5.6 (75) n-type socket (50) composite colour picture input/output, rgb output scart socket video input/output 2 x bnc socket transport current input/output 2 x sub d socket (25-pole) asi input/output 2 x bnc socket common interfa...
Page 22: Service
22 service device calibration device maintenance is essentially limited to cleaning the exterior. The calibration interval is dependent on operational demands made on it and should be carried out every 1 to 2 years. The calibration can be carried out by esc kathrein customer service, see below. Exte...
Page 23: Service
23 service if, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly, or if unexpected problems occur, please contact your specialist dealer. Main services www.Esc-kathrein.De fa. Esc elektronik service chiemgau gmbh bahnhofstr. 10...
Page 24
Internet: http://www.Kathrein.De kathrein-werke kg • anton-kathrein-straße 1 - 3 p.O. Box 10 04 44 • 83004 rosenheim/germany 936.3448/a/0209/zwt - t echnical data subject to change!.