- DL manuals
- Kathrein
- Inverter
- MVG 10
- Operator's Manual
Kathrein MVG 10 Operator's Manual
Summary of MVG 10
Page 1
Operator's manual video sweep generator mvg 10 order no.: 208 320
Page 2
2.
Page 3
Preface 3 preface dear customer, this handbook aims to help you use the various functions of the mvg10 in the optimal manner. Please pay attention to all instructions. Kathrein-werke kg has made every effort to ensure the information and descriptions are correct and complete. We reserve the right to...
Page 4
4.
Page 5
Contents 5 contents preface .....................................................................................................................................................3 contents ...................................................................................................................
Page 6
Safety notes 6 safety notes validity of handbook this handbook is valid for mvg 10, order no.: 208 320. The following notes are important for operating the mvg 10 and should be observed under all circumstances. General safety notes the mvg 10 was developed and produced in compliance with the relevan...
Page 7
Safety notes 7 safety notes always observe the vde safety regulations. Observe the maximum permissible signal feed-in level. Neither dc voltage nor low-frequency ac voltage may be applied to the rf port. Only use fuses with the same cut-out characteristics. The unit is live even when not connected. ...
Page 8
System description and usage 8 system description and usage the mvg 10 video sweep generator is designed to selectively sweep and measure the forward path and return path of television cable installations without interfering with the connected subscribers. The required sweep ranges, channels and sig...
Page 9
System description and usage 9 downstream measurement: 47…860 mhz head-end (or transfer point) transfer point (or terminal outlet) cable installation with return path-capable amplifiers upstream measurement: 4.0…80 mhz head-end (or transfer point) transfer point (or terminal outlet) cable installati...
Page 10
System description and usage 10 the spectrum at the head-end can be printed out from the msk 33 (1) using the print command "prt 999" on the mvg 10 (1). The command "clear" clears the spectrum presentation on the msk 33 (1). Downstream measurement: the mvg 10 (2) is switched from signal generator mo...
Page 11
Views, connections and controls 11 views, connections and controls left-hand side scart socket right-hand side rs232 socket power supply frontal view rf output display keypad.
Page 12: ▲
Button functions 12 button functions the following information explains the operation of the mvg 10. Please use the illustration of the operating concept for assistance. Button function display on off 1. Switch on unit when depressed briefly the upper display appears first, then the lower display wi...
Page 13: ▲
System settings 13 system settings we recommend checking the factory settings before initial start-up. Please use the operating concept on page 2 for help with understanding the operating sequence. Function button actuation display switch on unit when depressed briefly the upper display appears firs...
Page 14
System settings 14 display units ▼ w x + - + system baud rate ▼ setting not possible transmission readiness ▼ setting not possible confirm entries menu select system.. Accu 100 % sys unit dbµv (dbmv, dbm) sys rts/cts on sys baudr: 19.2k.
Page 15: ▲
Noise generator 15 noise generator the noise generator is used for measuring cable installations or sections of cable installations that are not yet occupied with programming. It generates a broadband noise to evaluate the frequency response in the range from 4 mhz to 1 ghz. The bandwidth can be set...
Page 16: ▲
Signal generator 16 signal generator the signal generator is needed to transmit test signals and the screen view from the msk 33 during "comfortable up/downstream measurement" (see system description). In addition to an internal test picture of coloured bars it has an external modulation input (cvbs...
Page 17
Signal generator 17 enter transmission frequency directly followed by "enter" channel frequency inputs with incorrect entries after the point are not accepted! Or 0 9 see above channel entry - special channels with press · s-ch first! ▼ w x + - + enter channel number directly special channels with p...
Page 18
Sweep generator 18 sweep generator the sweep generator is used to sweep in 10 preset frequency ranges (measuring profiles). The profiles can be programmed to free ranges depending on the channel allocation in the cable network, so that measurement is possible without interrupting or interfering with...
Page 19
Sweep generator 19 enter start frequency ▼ w x + - + enter frequency directly or 0 9 see above enter end frequency ▼ w x + - + enter frequency directly or 0 9 see above 50-khz steps from one frequency to next in mhz ▼ w x + - + enter frequency directly or 0 9 see above step duration from one frequen...
Page 20
Sweep generator 20 clear screen presentation on msk 33 with "enter" ▼ x + + + command to clear spectrum received by msk33 (mvg10 tracking) ▼ enter control printout number (up to 3 digits), confirm with "enter" and run with "enter" x + + + 0…..9 command to switch a second mvg10 to stored position "re...
Page 21
Sweep generator operating concept 21 the respective freqrange (frequency range) can be selected using numbers 0…9. Prt prints out at msk33 fkt a sets uscart at msk33 fkt b cvbs input at msk33 clear clears the screen of msk33 (sw itchover rec 0/1) (ex t. Cvbs picture presentation) swg level 60.0 dbµv...
Page 22
Channel sweep generator 22 channel sweep generator the channel sweep generator is used to sweep in 10 preset ranges. The channels can be programmed to free ranges depending on the channel allocation in the cable network, so that measurement is possible without interrupting or interfering with progra...
Page 23
Channel sweep generator 23 enter start channel special channels with press · s-ch first! ▼ w x + - + enter channels directly or 0 9 see above enter end channel special channels with press · s-ch first! ▼ w x + - + enter channels directly also switch back to normal channel entry with or 0 9 · s-ch se...
Page 24
Channel sweep generator 24 set standards b/g, d/k, i, m, mj, h ▼ w x + - + set the pre-programmed channel ranges to be processed (0…9) ▼ command to clear spectrum received by msk33 (mvg10 tracking) ▼ enter control printout number (up to 3 digits), confirm with "enter" and run with "enter" x + + + 0…...
Page 25
Channel sweep generator operating concept 25 the respective chanrange (channel range) can be selected using numbers 0…9. Setting modulation type prt prints out at msk33 fkt a sets uscart at msk33 fkt b cvbs input at msk33 clear clears the screen o f m s k 33 (sw itchover rec 0/1) (ex t. Cvbs picture...
Page 26
Recall 26 recall the "recall" setting is used to call up the setting stored at addresses 0…9 and start the measuring process. Please use the operating concept on page 2 for help with understanding the operating sequence. Function button actuation display switch on unit when depressed briefly the upp...
Page 27
Technical appendix 27 technical appendix technical data frequency range: 4.0 mhz...1000 mhz frequency adjustment: 50 khz frequency resolution: 62.5 khz display: lcd alphanumeric 2 x 16 characters, bar chart; illuminated adjustment: direct frequency and channel entry; +/- step buttons sweep ranges: 1...
Page 28
Internet: www.Kathrein.De kathrein-werke kg phone +49 8031 184-0 fax +49 8031 184-306 anton-kathrein-straße 1-3 p.O. Box 100 444 83004 rosenheim germany 936.2879/-/1105/zwt/e tec hnical data subject to change..