1. DL manuals
  2. Kathrein
  3. Satellite TV System
  4. UFS 922 si
  5. Operating Manual

Kathrein UFS 922 si Operating Manual

Manual is about: Twin HDTV satellite receiver with hard disk

Summary of UFS 922 si

  • Page 1

    Operating manual english ufs 922 si/sw twin hdtv satellite receiver with hard disk.

  • Page 2: Preface

    Dear customer, this operating manual is intended to help you make the fullest use of the extensive range of functions offered by your new receiver. We have tried to make the operating instructions as easy as possible to understand, and to keep them as concise as possible. To help you understand part...

  • Page 3: Contents

    Contents preface............................................................................................................................................................................. 2 contents ......................................................................................................

  • Page 4

    4 danger! Warning! Caution! Gb safety instructions – important information this page contains important information about the operation, installation location and connection of the unit. Read these instructions carefully before starting to use the unit. Mains cable make sure that the mains cable (po...

  • Page 5: Important Information

    5 make sure that the fan at the rear of the unit and the ventilation slots on the unit are not blocked or covered in any way. Otherwise the unit may overheat. Adjust the fan speed to the temperature conditions in the receiver. There is a risk of fire! Important information channel assignment the cha...

  • Page 6: Important Information

    6 information on audio mpeg inc. And s.I.Sv.El, s.P.A: this unit makes use of legally protected technologies, which are protected by patents in the usa and also by other intellectual property rights in other countries. Kathrein-werke kg has obtained licences from audio mpeg inc. And societa‘ italian...

  • Page 7

    7 ufs 922si or ufs 922sw remote control rc 670 hdmi cable scart cable coaxial loop-through cable for loop-through operation batteries aaa 1.5 v power supply cable operating manual safety instructions (multi-lingual) receiver features/scope of supply/features receiver features scope of supply the ufs...

  • Page 8

    8 receiver features/scope of supply/features features reception of digital satellite tv channels and radio programmes using dvb-s and dvb-s2 transmission standards video decoding of mpeg 2 and mpeg 4/h.264 signals two independent hdtv satellite tuners with loop- through output integral 500 gb hard d...

  • Page 9: Connection and Setup

    9 connection and setup view of rear panel ~ 1 10 2 3 4 5 6 7 8 9 11 12 16 13 14 15 17 1. On/off switch (disconnection from the mains) . Mains power cable . Fan 4. Optical data stream output (spdif/sony philips digital interface format) for dolby digital ac audio 5. Data interface (for service only) ...

  • Page 10: 2 3

    10 connect the sat-if inputs on the receiver to the satellite reception system. Use coaxial cable with an f standard connector. If the f standard connectors are not yet fitted on the cables, strip the insulation from the cables as shown in the following illustration and carefully screw the f standar...

  • Page 11: Connection and Setup

    11 information about antenna connection and loop-through mode to enable you to utilise all the reception and recording features of your ufs 922 twin-pvr hdtv sat receiver, such as 1. Recording one programme and simultaneously viewing any other programme or zapping through the channels, and . Recordi...

  • Page 12: Connection and Setup

    1 connection and setup connection example conventional diseqc™ system ~ hi-fi system network pc/laptop dolby digital system external hard disk connection sequence for single-cable matrices.

  • Page 13: Connection and Setup

    1 connection and setup connect the satellite receiver (hdmi or alternatively tv scart socket) and the tv set using an hdmi or scart cable (see “connection example”). If your tv is stereo, you can receive the sound in stereo via the hdmi or scart connection. For system reasons, the same video signals...

  • Page 14: Connection and Setup

    14 connection and setup first installation required buttons on remote control for first installation: ... Numerical input (green) proceed to next step in first installation (red) go back one step in the first installation confirm the changed values/setting select/change individual menu parameters, n...

  • Page 15: Connection and Setup

    15 connection and setup the following display appears: use the buttons here to select the basic settings for the video and audio output from the receiver to the tv set. For this, refer to the operating manual for your tv set and take care to select only those settings that your tv set can process. V...

  • Page 16: Connection and Setup

    16 audio format via hdmi here you can select the type of audio signal that is transmitted by the hdmi interface. Select the signal that your tv set can process: - decoded pcm or - s/pdif format auto dolby digital output here you can select whether the receiver should automatically select the dolby d...

  • Page 17: Connection and Setup

    17 separated: the second tuner input of the receiver, identified at the rear of the unit by “lnb2 in”, receives its own signal input (i.E. There is a direct connection between the antenna socket and tuner input 2). See example illustration on the right. Before you start configuring the tuner for you...

  • Page 18: Connection and Setup

    18 the following configuration options are available for: tuner 2 connection type “loopthrough”: all settings are made on tuner 1. The second tuner is fed from the looped through output of the first tuner. Available settings for tuner 1 are: “diseqc™1.0”, “diseqc™1.1”, “motorized antenna” and “simpl...

  • Page 19: Connection and Setup

    19 connection and setup the individual items are selected using the buttons. If you require to access submenus, they can be called up using the button. Changes to the current settings can be made using the buttons or the numeric keypad. The following display appears: select satellites - tuner 1 here...

  • Page 20: Connection and Setup

    0 connection and setup the following display appears: satellite configuration - tuner 1 make the settings for the first satellite for tuner 1 here. Lnb type: if your reception system does not have a universal lnb, use the buttons to select the lnb types that are used in your reception system. You ca...

  • Page 21: Connection and Setup

    1 connection and setup khz signal: you only need to specify this data if your lnb type is “simple”. The 22 khz signal is needed to switch lnbs in multi-feed reception and to switch between low and high band. - on - off test-transponder: select the “test-transponder” field. Here you can select a tran...

  • Page 22: Connection and Setup

    Connection and setup the following display appears: select satellites - tuner 1 here, you can select the available satellites (max. 64) included in the signal on tuner 1. Use the buttons to select the satellite you want and confirm your selection with the button. The selected satellites will be iden...

  • Page 23: Connection and Setup

    Connection and setup lnb frequency (mhz): you only need to specify this data if your lnb type is not “universal lnb”. The data required differ for the settings “simple” and “user-defined”. Refer to the documentation supplied for your lnb. - selection “simple” lnb: use the numeric keypad to enter the...

  • Page 24: Connection and Setup

    4 connection and setup the individual items are selected using the buttons. If you require to access submenus, they can be called up using the button. Changes to the current settings can be made using the buttons or the numeric keypad. Motorized antenna (diseqc™1.2/diseqc™1.3) press the (green) butt...

  • Page 25: Connection and Setup

    5 connection and setup the following display appears: motor control select the control type “diseqc™1.2”. Refer to the documentation for your motorized antenna for details. Go to null position select the “go to null position” field. Press the button to instruct the turntable to move to its null posi...

  • Page 26: Connection and Setup

    6 connection and setup the following display appears: lnb type: if your reception system does not have a universal lnb, use the buttons to select the lnb types that are used in your reception system. You can choose from the following lnb types: - universal - simple or - user-defined lnb frequency (m...

  • Page 27: Connection and Setup

    7 connection and setup set the turntable so that both of the bars “signal-strength” and “signal-quality” on the right of the screen show the highest available percentage values. Test-transponder: select the “test-transponder” field. Here you can select a transponder for checking whether your setting...

  • Page 28: Connection and Setup

    8 connection and setup set borders select the “set borders” field. In this menu you can set the limits for your turntable. This is particularly necessary if the turntable has only a restricted range in which it can turn before striking an obstruction (such as a wall or tree). Press the button. The f...

  • Page 29: Connection and Setup

    9 connection and setup the following display appears: lnb type: if your reception system does not have a universal lnb, use the buttons to select the lnb types that are used in your reception system. You can choose from the following lnb types: - universal - simple or - user-defined lnb frequency (m...

  • Page 30: Connection and Setup

    0 the individual items are selected using the buttons. If you require to access submenus, they can be called up using the button. Changes to the current settings can be made using the buttons or the numeric keypad. Simple lnb press the (green) button. Connection and setup the following display appea...

  • Page 31: Connection and Setup

    1 connection and setup lnb type: if your reception system does not have a universal lnb, use the buttons to select the lnb types that are used in your reception system. You can choose from the following lnb types: - universal - simple or - user-defined lnb frequency (mhz): you only need to specify t...

  • Page 32: Connection and Setup

    Use the buttons to select “on” in the “onecable system used” line. Then use the buttons to switch to the “onecable system” field. The following display appears: use the buttons to select the one cable system used in your reception system: - exr ... / exu ... For all kathrein one cable matrices - uas...

  • Page 33: Connection and Setup

    Connection and setup the following display appears: select satellites - tuner 1 here you can select up to two satellites included in the signal on tuner 1. Use the buttons to select the satellite you want and confirm your selection with the button. The selected satellites will be identified with a t...

  • Page 34: Connection and Setup

    4 when you have completed all settings, press the (green) button. The individual items are selected using the buttons. Changes to the current settings can be made using the buttons or the numeric keypad. The following display appears: protect the channel with a pin: if your one cable system allows t...

  • Page 35: Connection and Setup

    5 connection and setup the following display appears: lnb type (settings): if your reception system does not have a universal lnb, use the buttons to select the lnb types that are used in your reception system. You can choose from the following lnb types: - universal - simple or - user-defined lnb f...

  • Page 36: Connection and Setup

    6 refer to the documentation supplied with the uas 481 for the settings for “tuner 1” and “tuner 2”. No frequency can be used by more than one receiver. The receivers would interfere with each other. Do not assign the same frequencies/channels to tuner 1 and tuner 2. Connection and setup the individ...

  • Page 37: Connection and Setup

    7 connection and setup transmission channel for tuner 1: select a free available transmission channel (scr 0 - scr 3). Transmission channel for tuner : select a free available transmission channel (scr 0 - scr 3). When you have completed all settings for the satellite, press the (green) button. The ...

  • Page 38: Connection and Setup

    8 connection and setup onecable system - user-defined the following display appears: select satellites - tuner 1 here you can select up to two satellites included in the signal on tuner 1. Use the buttons to select the satellite you want and confirm your selection with the button. The selected satel...

  • Page 39: Connection and Setup

    9 connection and setup the individual items are selected using the buttons. Changes to the current settings can be made using the buttons or the numeric keypad. The following display appears: make the settings for the second tuner in the same way as for the first tuner. Protect the channel with a pi...

  • Page 40: Connection and Setup

    40 the following display appears: lnb type (settings): if your reception system does not have a universal lnb, use the buttons to select the lnb types that are used in your reception system. You can choose from the following lnb types: - universal - simple or - user-defined lnb frequency (mhz): you ...

  • Page 41: Connection and Setup

    41 channel search the individual items are selected using the buttons. Changes to the current settings can be made using the buttons. If you do not want to perform a channel search, press the (green) button and continue with the chapter “date and time”. If you want to perform a channel search, use t...

  • Page 42: Connection and Setup

    4 connection and setup network search use the buttons (on/off) to select whether a network search should be performed. If you set the network search to “off”, only the factory default transponders for the satellite(s) you previously selected will be searched for new as yet unsaved channels. If you s...

  • Page 43: Connection and Setup

    4 date and time the individual items are selected using the buttons. Changes to the current settings can be made using the buttons. Connection and setup time setup here you can select whether the time information should be obtained by the receiver automatically from a specific channel that you selec...

  • Page 44: Connection and Setup

    44 automatic manual you need not input any further data, the receiver will automatically update the date and time. Use the numeric keypad or the buttons to input the correct date. Then use the buttons to switch to the “time” field and use the numeric keypad or the buttons to input the correct time. ...

  • Page 45

    45 general operating instructions topic page alphanumeric inputs ..................................................................................................................................................... 45 editing and selection options in the menus ..........................................

  • Page 46

    46 general operating instructions after you have input the desired term, press the button to enter the name/search expression or press the or button to cancel the input. Switch between upper case and lower case letters confirm the term input cancel input without saving cancel input without saving al...

  • Page 47

    47 general operating instructions explanation of symbols in receiver display various symbols are occasionally shown in the receiver display above the normal display (channel name). These are not displayed permanently, they only appear for specific functions, procedures or channel features. You can f...

  • Page 48

    48 basic operation in tv or radio mode (live operation) remote control for live operation (tv/radio) = call up favourites list = not currently supported volume “-” (softer) volume “+” (louder) select teletext operation (on)/standby (off) call up the help function numeric keypad select main menu mute...

  • Page 49

    49 basic operation in tv or radio mode (live operation) switching between tv and radio operation adjusting the volume channel selection channel selection from the channel list to switch between tv and radio mode, press the (blue) button. The volume is adjusted using the buttons. The button allows th...

  • Page 50

    50 now use the relevant coloured button to select the category from which you want to open a channel list: channel list selection: use the buttons to scroll through the currently available channel lists. If you want to see an overview of the currently available channel lists, press the coloured butt...

  • Page 51

    51 channel information channel information is shown for a few seconds each time the channel is changed (this can be changed under “settings”, “user-defined settings”, “customise screen menu”) or displayed continuously by pressing the button. Broadcaster logo channel slot in the selected channel list...

  • Page 52

    5 calling up the channel options if the channel osd contains the following icon , this is a portal channel. Press the (yellow) button, use the buttons to select “channel options” and press the button to confirm your selection. The following display then appears (example): use the buttons to select y...

  • Page 53

    5 select audio track if the channel banner displays 1/ in front of the symbol for the selected soundtrack, this tells you that you have currently selected the first of the three available soundtracks. Press the (yellow) button, use the buttons to select “select audio track” and press the button to c...

  • Page 54

    54 teletext this symbol in the channel information shows you whether teletext is available for the selected channel. When you press the button, the receiver processes the teletext service data for your tv set to display, even when the signal is encrypted. During the search, the page which is being s...

  • Page 55

    55 one-touch recording (otr) basic operation in tv or radio mode (live operation) to start recording directly to the hard disk, press the (red dot) button. The following display appears (example): use the buttons to select the lines to be changed; make the changes using the buttons. Recording: you h...

  • Page 56: Premium

    56 premium epg you will only see information on the current or subsequent programmes in the epg if this data is supplied/transmitted by or by the channel provider. If no epg data is available, the receiver shows the message “no data available” instead of showing information on the current program. G...

  • Page 57: Premium

    57 premium epg calling up the epg the epg is opened by pressing the button. You will automatically see the view you selected in the menu (“settings”, “user-defined settings”, “epg settings”) - irrespective of which view you selected last time before exiting the epg. The following display appears (ex...

  • Page 58: Premium

    58 premium epg - (red) button open the timer list (display of all pre-programmed recordings/reminders) - button navigation in the individual views (e.G. 15 minutes skip forward in the “current” view) - (yellow) button open a preview of the currently selected channel (programme listings) - (blue) but...

  • Page 59: Premium

    59 premium epg views of the epg “current” view the “current” view can be called up at any time in epg by pressing the (green) button. In the “current” view you can see all channels displayed in the order of the overall channel list. Provided that epg data has been supplied/transmitted by or by the c...

  • Page 60: Premium

    60 premium epg “coming up” view (programme listings) the “coming up” view can be called up at any time in epg by pressing the (yellow) button. In the “coming up” view you will see all the programmes that will be shown on the channel previously selected in the “current” view. Provided that epg data h...

  • Page 61: Premium

    61 premium epg categories view the “coming up” view can be called up at any time in epg by pressing the (blue) button. In the “categories” view you can see all programmes, sorted by category and start time. The following main categories are available for selection: pick of the day, my hints (see “ex...

  • Page 62: Premium

    6 premium epg you can create your own categories within this section. Press the button to activate the input field. Now you can enter the search expression/category name for your new category. Alphanumeric characters are input as described in “operating instructions”, “alphanumeric entries”. To sear...

  • Page 63: Premium

    6 premium epg in this section you have the facility to select an actor that is shown in the actors list (using the cursor ( ) buttons) and the by pressing the button to search through all available data for programmes in which this person appears. If there are programmes available for which the name...

  • Page 64: Premium

    64 search function premium epg the search function can be called up in epg at any time by pressing the button. The following display appears (see screenshot on the right). You have the following search options: - further programme times for the currently selected programme (in the example on the rig...

  • Page 65: Premium

    65 premium epg full text search after calling up the search function, press the button again to gain access to the full text search. The following display appears (see example on the right): if necessary the last search expression used is offered. Pressing the button allows you to delete your input ...

  • Page 66: Premium

    66 premium epg recording settings (programming the timer) the (red dot) button allows you to set a programme for recording at any time. The programme to be recorded can be selected in any of the epg views, provided the (red dot) button appears at the bottom of the screen display. Programme appears i...

  • Page 67: Premium

    67 information on direct decryption using timers (recordings on encrypted channels): the “decrypt” field only appears when recording encrypted channels. If you want to make the recording unencrypted, use the buttons to select “yes”; if you want the recording to be made encrypted on the hard disk, se...

  • Page 68: Premium

    68 recording “once” use the buttons to select the “once” recording mode (see screenshot on the right). Use the buttons to switch to the “date” field and use the buttons to select the desired recording day. Use the buttons to switch to the “start” field and use the buttons or the number buttons to se...

  • Page 69: Premium

    69 premium epg recording “daily” use the buttons to select the “daily” recording mode (see screenshot on the right). Use the buttons to switch to the “start” field and use the buttons or the number buttons to select the desired recording start time. Use the buttons to switch to the “end” and field u...

  • Page 70: Premium

    70 premium epg recording “user-defined” use the buttons to select the “user-defined” recording mode (see screenshot on the right). Use the buttons to switch to the “day” field and use the buttons to select the required day for the recording. Press the button to fix the selection (the day will be sho...

  • Page 71: Premium

    71 premium epg reminder function (switch over to programme) if you want to be reminded that a programme is about to start, you can activate the reminder function for the desired programme. The reminder function is set up in exactly the same way as programming a recording. The only difference is that...

  • Page 72: Premium

    7 premium epg timer list view the “timer list” view can be called up at any time in epg by pressing the (red) button. The following display appears (example): the timer list view shows you all the recordings and reminders that are scheduled (marked green). The buttons allow the recordings to be sort...

  • Page 73: Premium

    7 premium epg when editing a recording, you can change all parameters apart from the recording mode. Make the changes using the cursor ( ) buttons and the numeric keypad. Press the button to confirm your changes, and return to the timer list view. Editing a recording if your scheduled recordings ove...

  • Page 74: Editing The Channel List

    74 editing the channel list calling up the “tv-channellist” menu topic page you have two ways of accessing the edit menu for the channel lists: 1. Directly via the channel list • on the tv picture, press the button to open the channel list • then press the (red dot) button or 2. Using the “edit chan...

  • Page 75: Editing The Channel List

    75 in the following chapter we have chosen to use the first option to explain the editing of the channel lists. The following display appears (example): selecting the channel list/favourites list to be edited now use the relevant coloured button to select the desired channel list category (refer to ...

  • Page 76: Editing The Channel List

    76 selecting the channels to be edited select a channel in the selected channel list/favourites list using the cursor ( ) buttons (see example screenshot on the right). To select several channels to be edited at the same time, if they are not listed directly following each other in the selected chan...

  • Page 77: Editing The Channel List

    77 move use the buttons to select “move” and confirm your selection with the button. The following display appears (see example screenshot on the right): now use the cursor ( ) buttons or the numeric keypad to select the new channel memory position(s), then confirm the insertion with the button. Del...

  • Page 78: Editing The Channel List

    78 lock use the buttons to select “lock” and confirm your selection with the button. To lock the channel you must now enter your four-digit pin code (factory setting: 0000). The following display appears (see example screenshot on the right): the locked channel is now displayed in the channel list w...

  • Page 79: Editing The Channel List

    79 if several channels use the same data, the following warning message is displayed when you deactivate the function (see screenshot on right). In this case, no data is stored for the other affected channels. You can only use this function if premium epg data is available for the selected channel. ...

  • Page 80: Editing The Channel List

    80 editing channels (favourites lists) after selecting the channel(s) to be edited, press the (red dot) button. The following display appears (see screenshot on the right). “start blockselection” only appears if just one channel has been selected for editing. Move see “editing channels (channel list...

  • Page 81

    81 recording archive (play back/edit recordings) topic page calling up the recording archive the recording archive is called up by pressing the button or the button. Each time the epg is opened, you will automatically be shown the view you had selected the last time you exited the archive. The follo...

  • Page 82

    8 recording archive (play back/edit recordings) - (red) button call up the chapter view or the automatic creation of chapters (if not yet available) - (green) button call up ordering of recordings (ordered by date, ordered by title and ordered by duration) - (yellow) button display the recordings by...

  • Page 83

    8 views of the recording archive (sorting the recordings) recording archive (play back/edit recordings) when displaying the recordings you have the following sorting/display options: - (green) button ordered by date (you can use the buttons to choose between the sorting criteria of date, title or du...

  • Page 84

    84 recording archive (play back/edit recordings) folders in the recording archive from software version 1.02, the ufs 922 includes the option of creating folders in the recording archive. You can give these folders the names of your choice and add recordings to them. Creating folders use the buttons...

  • Page 85

    85 recording archive (play back/edit recordings) use the buttons to select the desired recording. Confirm selection of the desired recording by pressing the button. Pressing the button again exits the recording archive and allows the desired recording to be viewed in full-screen mode. Playback start...

  • Page 86

    86 recording archive (play back/edit recordings) you will see this display after starting playback of the recording in full- screen mode or by pressing the button once you will see this display during all types of fast forward/rewind or by pressing the button or button o ok button call up the record...

  • Page 87

    87 recording archive (play back/edit recordings) selecting the recordings to be edited to select a recording, select the desired recording in the selected sort list, using the cursor ( ) buttons (see example screenshot on the right). If the relevant recording is stored in one of the folders you have...

  • Page 88

    88 recording archive (play back/edit recordings) delete use the buttons to select “delete” and confirm your selection with the button. The selected recording(s) will be deleted. Deleted recordings are irrevocably deleted and can only be restored by re-recording the programme! Lock use the buttons to...

  • Page 89

    89 recording archive (play back/edit recordings) changing the category use the buttons to select “change category”. Now use the buttons to select the desired category (see example screenshot on the right), to which the recording(s) should be assigned. Confirm your selection with the button. If no ap...

  • Page 90

    90 recordings: cut, split, copy use the buttons to select “recording”. Now use the buttons to select the desired action (see example screenshot on the right) and confirm your selection using the button. Before cutting or splitting a recording for the first time you should make a copy of the recordin...

  • Page 91

    91 recording archive (play back/edit recordings) the following display appears (example): now use the cursor ( ) buttons, the buttons or the button to select the desired start of the section to copy and then confirm by pressing the button. The following display appears (example): now use the cursor ...

  • Page 92

    9 recording archive (play back/edit recordings) cut the following display appears (example): now use the cursor ( ) buttons, the buttons or the button to select the desired start of the section to be cut from the recording, and then confirm by pressing the button. The following display appears (exam...

  • Page 93

    9 recording archive (play back/edit recordings) split the following display appears (example): now use the cursor ( ) buttons, the buttons or the button to select the desired time at which the recording should be split, and then confirm by pressing the button. The following display appears (example)...

  • Page 94

    94 moving to a folder you can use this function to move the recording selected before calling up the edit menu to a folder you have created. Use the buttons to select “move to folder...”. Then press the button. The currently available folders are displayed. Use the buttons to select the desired fold...

  • Page 95

    95 copying to usb data carrier use the buttons to select “copy to usb device” and confirm your selection with the button. The following display appears (example): the connected usb data carrier must be “fat/fat 32” formatted. Successful usb data carrier initialisation is indicated by the “usb” and “...

  • Page 96

    96 note: when the chapter view is called up, the receiver automatically creates seven chapters for the recording you select, if this has not already been done. This function is not performed if you have already created chapters manually. Use the buttons to select the desired chapter. To start playba...

  • Page 97

    97 deleting chapters deleting a chapter: use the buttons in the chapter overview to select the chapter to be deleted, and press the (red dot) button. The following display appears (see screenshot on the right). Use the buttons to select “delete” and confirm your selection with the button. The select...

  • Page 98: Main Menu

    98 main menu topic page calling up the main menu and introduction the main menu is opened by pressing the button. The following display appears: the programme showing on the currently selected channel always appears in the top right-hand corner of the main menu. The selected menus, sub-menus and ite...

  • Page 99: Main Menu

    99 main menu menu overview main menu (call up by pressing the c button) edit channel lists channel search service menu settings interfaces applications language selection automatic search automatic software update first installation (see “connection and set-up”, “first installation” chapter) common ...

  • Page 100: Main Menu - Channel Search

    100 main menu - channel search automatic channel search after calling up the menu you will see the following display: you have three different search options: - automatic channel search - manual channel search - search with service id use the buttons to select the desired search type and confirm you...

  • Page 101: Main Menu - Channel Search

    101 network search use the buttons (on/off) to select whether a network search should be performed. If you set the network search to “off”, only the factory default transponders for the satellite(s) you previously selected will be searched for new as yet unsaved channels. If you set the network sear...

  • Page 102: Main Menu - Channel Search

    10 manual channel search main menu - channel search after calling up the menu you will see the following display: the buttons allow you to select different sets of parameters for the search. Satellite use the buttons to select the satellite on which the transponder you want to search is located. By ...

  • Page 103: Main Menu - Channel Search

    10 search with service id main menu - channel search symbol rate use the numeric keypad to enter the relevant symbol rate. Channel search mode use the buttons to select the type of channels that are to be searched for. You have three options: - “free & scrambled” all channels are searched for - “onl...

  • Page 104: Main Menu - Channel Search

    104 note: you can cancel the search at any time by pressing the button. The following displays during and in connection with the search are identical to those for the automatic search. Transponder frequency use the buttons (transponder frequency already saved) or the keypad (transponder frequency no...

  • Page 105: Main Menu - Service Menu

    105 main menu - service menu after calling up the menu you will see the following display: you can choose between various different menus: - automatic software update - software update - software update by usb - factory reset in addition, the following information is displayed in the service menu un...

  • Page 106: Main Menu - Service Menu

    106 main menu - service menu if new software or changes to the channel list are found, you will see the following display the next time you start the ufs 922: press the button to perform the software update. After the software update, you will see the following display (only if there are any changes...

  • Page 107: Main Menu - Service Menu

    107 after calling up the menu you will first see the following display: software update the following display then appears: use the buttons to select the parameters to be updated during the update procedure. Show infotext: press the button to display the info text for the available downloads. These ...

  • Page 108: Main Menu - Service Menu

    108 main menu - service menu follow all on-screen instructions! Check the time setting following a software update! You can also download the updates from the internet. The address is: http://www.Kathrein.De you will find the software at “service” → “software and download” → “receiver” → “ufs 922” t...

  • Page 109: Main Menu - Service Menu

    109 after calling up the menu you will first see the following display: you can here restore the channel list and the installation settings to the factory settings. You can use the buttons to select the components to be restored to their factory settings. In each case use the buttons to select “yes ...

  • Page 110: Main Menu - Settings

    110 main menu - settings basic settings after calling up the menu you will see the following display: you can choose between various different menus: - first installation - basic settings - user defined settings - antenna & satellite use the buttons to select the desired menu and confirm your select...

  • Page 111: Main Menu - Settings

    111 tv settings after calling up the menu you will see the following display (depending on the selected signal output): for output of the tv picture via the hdmi output: for output of the tv picture via the scart-tv output: the individual items are selected using the buttons. Changes to the current ...

  • Page 112: Main Menu - Settings

    11 audio settings tv-scart-output select the type of video signal to be output at the tv scart socket here. Select the signal that your tv set can process. Either - rgb (red/green/blue signal) - y/c (s-video signal (luminance/chrominance), or - cvbs (colour video baseband signal) vcr-scart-output se...

  • Page 113: Main Menu - Settings

    11 preferred subtitle language select here your preferred subtitles language. You can choose between the following languages: deactivated (off), german, english, french, italian, spanish, czech, dutch, polish, turkish or russian. Audio format via hdmi here you can select the type of audio signal tha...

  • Page 114: Main Menu - Settings

    114 clock change (summer time) here you can select whether the receiver should automatically change over to and from summer and winter time. The “manual” setting only makes sense if you also selected “manual” for the selection item “time setup”, since otherwise the time information is obtained autom...

  • Page 115: Main Menu - Settings

    115 setting the remote control code main menu - settings after calling up the menu you will see the following display: you can now use the remote control for your receiver to set a new remote control code (the remote control code 1 is set as standard). Simultaneously press buttons: - + + 1 for remot...

  • Page 116: Main Menu - Settings

    116 parental lock user defined settings fan settings main menu - settings use the buttons to set the desired fan speed (revolutions per minute). Either - fast (1500 rpm) - medium (1000 rpm) - slow (500 rpm) the fan speed should be adjusted to the temperature changes in the receiver. After calling up...

  • Page 117: Main Menu - Settings

    117 main menu - settings the following display then appears: in this menu you can set various restrictions/parental controls. The individual items are selected using the buttons. The changes to the current settings can be made using the buttons or the numeric keypad. Lock mainmenu select here whethe...

  • Page 118: Main Menu - Settings

    118 main menu - settings customize screen menu after calling up the menu you will see the following display: the individual items are selected using the buttons. The changes to the current settings can be made using the buttons or the numeric keypad. Sleep timer you can use the “sleep timer” functio...

  • Page 119: Main Menu - Settings

    119 main menu - settings epg setup after calling up the menu you will see the following display: the individual items are selected using the buttons. Changes to the current settings can be made using the buttons or the numeric keypad. Epg grabbing select here the data with which the epg should be up...

  • Page 120: Main Menu - Settings

    10 recording settings after calling up the menu you will see the following display: the individual items are selected using the buttons. Changes to the current settings can be made using the buttons. Automatic timeshift select here whether automatic time-shifting is enabled or disabled. If this is s...

  • Page 121: Main Menu - Settings

    11 antenna & satellites (settings) main menu - settings after calling up the menu you will see the following display: if you do not have a meter for adjusting your reflector, you can use the sat finder as an alignment aid. However the sat-finder is not a complete substitute for a meter. The individu...

  • Page 122: Main Menu - Settings

    1 main menu - settings fec select the applicable error rate (viterbi rate). You need not state the error rate for the dvb s(sd) transponders. Instead a fixed display of “automatic” appears. You must state the correct error rate for the dvb s2(hd) transponders. Either qpsk 1/2, 2/3, 3/4, 3/5, 4/5, 5/...

  • Page 123: Main Menu - Settings

    1 frequency select here the desired transponder. By pressing the button at this point you can view a list of the transponders saved in the receiver for this satellite. Use the buttons to select the transponder you want and confirm your selection with the button. Symbol rate the symbol rate is positi...

  • Page 124: Main Menu - Settings

    14 delete satellites press the button to delete the currently selected satellite. As a security feature you are asked to confirm again by pressing the button that you really want to delete the satellite. Edit satellite name by pressing the button you can call up the input screen which allows you to ...

  • Page 125: Main Menu - Settings

    15 after calling up the menu you will see the following display: the individual items are selected using the buttons. If you need to access submenus, they can be called up using the button. Changes to the current settings can be made using the buttons or the numeric keypad. Edit transponders satelli...

  • Page 126: Main Menu - Settings

    16 main menu - settings symbol rate the symbol rate is positively assigned to each saved transponder, and cannot be changed. Polarization the polarization is positively assigned to each saved transponder, and cannot be changed. Edit transponders by pressing the button you can call up the input scree...

  • Page 127: Main Menu - Settings

    17 add a new transponder by pressing the button you can call up the input screen to save a new transponder. The following display appears: frequency: use the keypad to enter the transmission frequency for the new transponder. Dvb type: select here whether the selected transponder is to receive stand...

  • Page 128

    18 always follow the operating instructions from your pay-tv provider and the instructions supplied with the smartcard and the ca module! Smartcards and ca modules are not included with this product! The cards and modules are issued by the respective pay tv providers, and contain the subscriber data...

  • Page 129

    19 main menu - interfaces (ci, hard disk and network) you can find out which conditional access modules are in the ci slots on the ufs 922 and which smartcard is in which ca module from the “mainmenu” under “interfaces”, and the “common interface” menu. Confirmation is by pressing the button. The sc...

  • Page 130

    10 main menu - interfaces (ci, hard disk and network) information for conax, seca, viaccess and cryptoworks users: note that with monthly activation intervals, the channel providers have different procedures for activating pay tv cards. Activation may therefore be a few days before or after the begi...

  • Page 131

    11 main menu - interfaces (ci, hard disk and network) hdd management after calling up the menu you will see the following display: you have the following selection options: - format record archive (delete) - format media archive (delete) use the buttons to select the desired action. Deleted data can...

  • Page 132

    1 main menu - interfaces (ci, hard disk and network) ethernet settings after calling up the menu you will see the following display: these settings should not be made unless the receiver is linked into a network or is linked to a pc/laptop using a crossed over network cable. The ethernet interface u...

  • Page 133

    1 if with the “dhcp on” setting no connection can be established between the receiver and dhcp server/router, switch the setting to “dhcp off” and make the setting as described for (dhcp “off”). Configuration example: receiver: ip address: 19.168.0.11 subnet mask: 255.255.255.0 pc/laptop: ip address...

  • Page 134: Main Menu - Applications

    14 main menu - applications this menu displays applications that are installed on your ufs 922. This menu allows you to start and stop these applications. To do this, follow the instructions displayed and the explanations on the menu. Any modifications to the receiver software, or the use of applica...

  • Page 135

    15 main menu - language settings after calling up the menu you will see the following display: use the buttons to select the desired menu language and confirm your selection using the button. The following languages are available for selection: german, english, french, italian, spanish, czech, dutch...

  • Page 136: Tuner Configuration

    16 tuner configuration topic page call up the tuner configuration/tuner configuration general the main menu is opened by pressing the button. Use the “settings” buttons and confirm by pressing the button. Select the “antenna & satellite” buttons and confirm by pressing the button. Use the “tuner con...

  • Page 137: Tuner Configuration

    17 separated: the second tuner input of the receiver, identified at the rear of the unit by “lnb2 in”, receives its own signal input (i.E. There is a direct connection between the antenna socket and tuner input 2). See example screenshot on the right. Tuner configuration before you start configuring...

  • Page 138: Tuner Configuration

    18 the following configuration options are available for: tuner 2 connection type “loopthrough”: all settings are made on tuner 1. The second tuner is fed from the looped through output of the first tuner. Available settings for tuner 1 are: “diseqc™1.0”, “diseqc™1.1”, “motorized antenna” and “simpl...

  • Page 139: Tuner Configuration

    19 tuner configuration diseqc™1.0 the individual items are selected using the buttons. If you require to access submenus, they can be called up using the button. Changes to the current settings can be made using the buttons or the numeric keypad. Satellite 1 select “satellite 1:***” field and press ...

  • Page 140: Tuner Configuration

    140 lnb setting: select the “lnb setting” field. If your reception system does not have a universal lnb, press the button so that you can make the settings for the lnb. You can choose from the following lnb types: - universal - simple - user-defined tuner configuration if your lnb is neither a unive...

  • Page 141: Tuner Configuration

    141 diseqc™1.1 the individual items are selected using the buttons. If you require to access submenus, they can be called up using the button. Changes to the current settings can be made using the buttons or the numeric keypad. Tuner 1 select “tuner 1” field and press the button to allow you to make...

  • Page 142: Tuner Configuration

    14 lnb setting: select the “lnb setting” field. If your reception system does not have a universal lnb, press the button so that you can make the settings for the lnb. You can choose from the following lnb types: - universal - simple - user-defined tuner configuration if you select “universal” you n...

  • Page 143: Tuner Configuration

    14 motorized antenna tuner configuration the individual items are selected using the buttons. If you require to access submenus, they can be called up using the button. Changes to the current settings can be made using the buttons or the numeric keypad. Press the button. The following display appear...

  • Page 144: Tuner Configuration

    144 tuner configuration motorized antenna (diseqc™1.2) the individual items are selected using the buttons. If you require to access submenus, they can be called up using the button. Changes to the current settings can be made using the buttons or the numeric keypad. Motor control select the control...

  • Page 145: Tuner Configuration

    145 select satellites select the “select satellites” field. Select here which satellites you want to receive via your turntable. Pressing the button presents a display of the satellites stored in the receiver: use the buttons to select the satellites to be received and confirm your selection in each...

  • Page 146: Tuner Configuration

    146 stop on signal: select the “stop on signal” field. Here, you can select whether the motorized antenna should stop its rotary movement immediately on reception of a signal from the desired satellite. You can choose between “on” and “off”. Move motorized antenna: select the “move motorized antenna...

  • Page 147: Tuner Configuration

    147 set borders select the “set borders” field. In this menu you can set the limits for your turntable. This is particularly necessary if the turntable has only a restricted range in which it can turn before striking an obstruction (such as a wall or tree). Press the button. The following display ap...

  • Page 148: Tuner Configuration

    148 select satellites select the “select satellites” field. Select here which satellites you want to receive via your turntable. Pressing the button presents a display of the satellites stored in the receiver: use the buttons to select the satellites to be received and confirm your selection in each...

  • Page 149: Tuner Configuration

    149 tuner configuration simple lnb the individual items are selected using the buttons. If you require to access submenus, they can be called up using the button. Changes to the current settings can be made using the buttons or the numeric keypad. Satellite and position: select here the satellite yo...

  • Page 150: Tuner Configuration

    150 use the buttons to select “on” in the “onecable system used” line. The following display appears: press the button. The following display appears: use the buttons to select the one cable system used in your reception system: - exr ... / exu ... For all kathrein one cable matrices - uas 481 for t...

  • Page 151: Tuner Configuration

    151 tuner configuration onecable system - exr ... / exu ... After calling up the menu you will see the following display: press the button to access the system settings. The individual items are selected using the buttons. Changes to the current settings can be made using the buttons or the numeric ...

  • Page 152: Tuner Configuration

    15 make the settings for the second tuner in the same way as for the first tuner. Tuner configuration then press the button. Number of satellites select the “number of satellites” field and set the number of satellites to be received by your reception system. A maximum of two satellites can be recei...

  • Page 153: Tuner Configuration

    15 tuner configuration the following display appears: you can choose from the following lnb types: - universal - wideband - user-defined if your lnb is neither a universal nor a wideband lnb, select the setting “user-defined”. The “user-defined” setting means you must manually set the frequency rang...

  • Page 154: Tuner Configuration

    154 tuner configuration onecable system - uas 481 after calling up the menu you will see the following display: press the button to access the system settings. The individual items are selected using the buttons. Changes to the current settings can be made using the buttons or the numeric keypad. Th...

  • Page 155: Tuner Configuration

    155 the following display appears: satellite and position: select here the satellite you desire from the available satellites. By pressing the button at this point you can view a list of the satellites saved in the receiver. Use the buttons to select the satellite you want and confirm your selection...

  • Page 156: Tuner Configuration

    156 tuner configuration user-defined after calling up the menu you will see the following display: press the button to access the system settings. The individual items are selected using the buttons. Changes to the current settings can be made using the buttons or the numeric keypad. The following d...

  • Page 157: Tuner Configuration

    157 tuner configuration then press the button. You will be asked whether you want to save the changes. Use the buttons to select “yes, save the changes” and confirm with the button. If a connection to the one cable system cannot be established, check your settings (frequency and transmission channel...

  • Page 158: Tuner Configuration

    158 tuner configuration you can choose from the following lnb types: - universal - wideband - user-defined if your lnb is neither a universal nor a wideband lnb, select the setting “user-defined”. The “user-defined” setting means you must manually set the frequency ranges that are configured for you...

  • Page 159: Multimedia

    159 multimedia press the button to call up the multimedia menu. In addition to the familiar ftp server functionality from software version 1.01 for transferring data (recordings and pictures) via the network, from software version 1.02 the ufs 922 provides more extensive network functions. O upnp se...

  • Page 160: Multimedia

    160 multimedia the ufs 922 can operate as both a upnp media client and a upnp media server. Further information about upnp can be found on the internet at “www.Upnp.Org”. Upnp media client: streaming from external devices to the ufs 922 upnp media server: streaming from the ufs 922 to external devic...

  • Page 161: Multimedia

    161 the media centre has an integral mp player. The mp specific information display is based on “idtag info v2.3”. If this is not available, the file name is displayed instead of this information. Only files from the previously selected folder are played back. Use the buttons to select the track wit...

  • Page 162: Multimedia

    16 multimedia during playback, you have the following control options: pause start playback after pause next/previous track skip 30 seconds forwards or backwards / cancels mp playback and displays the media centre to change the settings for the mp player, press the (yellow) button after selecting th...

  • Page 163: Multimedia

    16 playback of xvid files functions in the same way as playback of an external recording (see “playback of external recordings”). Xvid playback multimedia pause start playback after pause; show/hide playback banner 10 % jumps forwards/back in recording skip 30 seconds forwards or backwards available...

  • Page 164

    164 operation from the front panel (without remote control) if you have misplaced your remote control, or if the batteries are flat, you can still operate your receiver from the front panel. The front panel houses four buttons and the multifunction control (from now on referred to as “the control”)....

  • Page 165

    165 operation from the front panel (without remote control) performing the software update you can also download the updates from the internet. The address is: http://www.Kathrein.De you will find the software at “service” → “software and download” → “receiver” → “ufs 922” 1. Use the remote control ...

  • Page 166: Troubleshooting

    166 troubleshooting in the event of a malfunction, first check all the cable connections and operating states: 1. Receiver and tv set power plugs are connected to wall socket . Antenna cables are connected to the receiver input 3. Receiver and tv set are correctly connected to each other by a hdmi o...

  • Page 167: Technical Appendix

    167 technical appendix technical specification type ufs 922si ufs 922sw order no. 01011 0101 colour silver black rf section sat if band mhz 950-2150 input level band dbµv 44-83 modulation, fec, demultiplexer dvb-s/dvb-s2 standard video resolution ccir 601 (70 x 576 lines), 576p, 70p, 1080i video dec...

  • Page 168: Technical Appendix

    168 technical appendix examples of one cable systems * ) the receiver must be programmed for one cable commands ** ) overvoltage protection kaz 11/kaz 12 sat-if sat-if 1400 can also be combined with exr 5xx sat-if 950-2150 mhz.

  • Page 169: Technical Appendix

    169 technical appendix * ) the receiver must be programmed for one cable commands ** ) overvoltage protection kaz 11/kaz 12 * ) the receiver must be programmed for one cable commands ** ) overvoltage protection kaz 11/kaz 12 sat-if 8 connections per living unit sat-if.

  • Page 170: Technical Appendix

    170 technical appendix * ) the receiver must be programmed for one cable commands ** ) overvoltage protection kaz 11/kaz 12.

  • Page 171: Technical Appendix

    171 technical appendix connection examples for network functionality pc/laptop gekreuztes netzwerkkabel ip-adresse: 192.168.0.10 ip-adresse: 192.168.0.11 ~ dhcp (receiver): off ip address: 19.168.0.11 ip address: 19.168.0.10 pc/laptop crossed network cable.

  • Page 172: Technical Appendix

    17 technical appendix pc/laptop netzwerkkabel switch/hub tcp/ip-adresse: 192.168.0.12 pc/laptop netzwerkkabel netzwerkkabel tcp/ip-adresse: 192.168.0.10 tcp/ip-adresse: 192.168.0.11 ~ dhcp (receiver): off tcp/ip address: 19.168.0.1 tcp/ip address: 19.168.0.10 tcp/ip address: 19.168.0.11 pc/laptop pc...

  • Page 173: Technical Appendix

    17 technical appendix pc/laptop netzwerkkabel dhcp-server, router (z. B. Fritzbox) pc/laptop netzwerkkabel tcp/ip-adresse: 192.168.0.13 tcp/ip-adresse: 192.168.0.12 tcp/ip-adresse: 192.168.0.11 tcp/ip-adresse: 192.168.0.10 netzwerkkabel netzwerkkabel ~ ~ dhcp (receiver): off network cable network ca...

  • Page 174: Technical Appendix

    174 technical appendix dhcp (receiver): on pc/laptop netzwerkkabel dhcp-server, router (z. B. Fritzbox) tcp/ip-adresse: automatisch funkstrecke ~ network cable radio link tcp/ip address: automatic pc/laptop dhcp server, router (e.G. Fritzbox).

  • Page 175: Comprehensive Index

    175 comprehensive index contents preface............................................................................................................................................................................. 2 difference between pal and hdtv .......................................................

  • Page 176: Comprehensive Index

    176 comprehensive index premium epg ................................................................................................................................................. 56 general information about premium epg ................................................................................

  • Page 177: Comprehensive Index

    177 comprehensive index lock ................................................................................................................................................................................................ 88 rename .......................................................................

  • Page 178: Comprehensive Index

    178 comprehensive index tuner configuration ................................................................................................................................................... 136 call up the tuner configuration/tuner configuration general ...............................................

  • Page 179: Brief Technical Glossary

    179 ac 3 output for dolby digital signal astra ses (société européene des satellites) satellite system. Analogue and digital transponders in the frequency range 10.7-12.75 ghz. Av programme pos. Preferred programme slot on tv set for external connections such as scart and hdmi cam – conditional acce...

  • Page 180: Brief Technical Glossary

    180 hdmi – high definition multimedia interface digital interface for digital video and audio data transmission (preferred for hdtv). Hdtv – high definition television high resolution television with a resolution up to 5 times higher or finer than pal or ntsc. However, there is no compatibility, as ...

  • Page 181: Brief Technical Glossary

    181 timer function clock function for pre-programmed switch on and off times timeshift function time shifted playback transponder a transponder is a frequency converter which receives tv and radio signals broadcast from the earth, converts them and the rebroadcasts them back to the earth at a differ...

  • Page 182: Service

    18 service if, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly, or if unexpected problems occur, please contact your specialist dealer. The kathrein customer hotline is also at your disposal. Phone: 0900/1140 * * (0.49 eur pe...

  • Page 183: For Your Notes

    18 for your notes.

  • Page 184

    Internet: http://www.Kathrein.De kathrein-werke kg • anton-kathrein-straße 1 - 3 p.O. Box 100 444 • 8004 rosenheim germany 936.3382/a/0309/zwt - technical data subject to change..