Kawasaki KX 250F - 2009 Use & Care Manual - page 7
13
W
Wo
okk C
Caasstt IIrro
on
n B
Bu
urrn
ne
err ((IIff aap
pp
plliiccaab
blle
e))
For proper lighting and performance of the burner, keep the
electric igniter and burner ports clean. It is necessary to clean these only
when the flame does not burn blue completely around all rings of the
burner, when there is a severe spillover or when the burner does not
light, even though the electric spark igniter sparks. Clean the burner by
scraping off burned on food soil. Use a wire, a straightened paper clip,
or needle to clean the ports. D
Do
o n
no
ott u
usse
e aa tto
oo
otth
hp
piicckk;; iitt cco
ou
ulld
d b
brre
eaakk o
offff
iin
n tth
he
e p
po
orrtt.. B
Be
e ssu
urre
e tth
he
e vve
en
nttu
urrii ttu
ub
be
e rre
em
maaiin
nss d
drryy..
W
Wo
okk P
Paan
n w
w//LLiid
d ((IIff aap
pp
plliiccaab
blle
e))
Wash the wok after each use in hot, soapy water. Do not use
harsh abrasives or scouring pad as they can harm the protective
seasoning. Dry thoroughly. Apply a light coat of cooking oil to the
inside surface with a paper towel. Place over medium heat for 15 - 30
seconds. Remove from heat and allow to cool. Wipe off excess oil
before storing in an inside cabinet. D
Do
o n
no
ott sstto
orre
e tth
he
e w
wo
okk p
paan
n aan
nd
d lliid
d
o
ou
uttd
do
oo
orrss..
Orifice
Venturi tube
Burner
ports
C
Clle
eaan
niin
ng
g aan
nd
d M
Maaiin
ntte
en
naan
ncce
e
Any piece of equipment works better and lasts longer when maintained
properly and kept clean. Cooking equipment is no exception. Your
rangetop must be kept clean and maintained properly.
Make sure all burners are “off” before cleaning. Disconnect power if
you are going to clean thoroughly with water.
12
P
Po
orrcce
ellaaiin
n P
Paarrttss ((G
Grraatte
e aan
nd
d G
Grraatte
e S
Su
up
pp
po
orrtt))
Allow the grate and grate support to cool to a safe temperature
level. Wipe up spillovers as soon as possible after they occur and before
they get a chance to burn in and cook solid. The grate and grate
support are coated with a porcelain enamel finish for durability. Wash in
hot, soapy water and rinse clean. For stubborn stains, use a mild
abrasive cleanser or non-abrasive soap-filled pad. Abrasive cleaners
used vigorously or too often can eventually scratch and harm the enamel.
C
Co
on
nttrro
oll P
Paan
ne
ell
DO NOT USE any cleaners containing ammonia or abrasives. They
could remove the graphics from the control panel. Use hot, soapy
water and a soft clean cloth.
C
Co
on
nttrro
oll K
Kn
no
ob
bss
MAKE SURE THE CONTROL KNOBS POINT TO THE OFF POSITION
BEFORE REMOVING. Pull the knobs straight off. Wash in detergent
and warm water. Do not soak knobs. Dry completely and replace by
pushing firmly onto stem. DO NOT USE any cleaners containing
ammonia or abrasives. They could remove the graphics from the knob.