1. DL manuals
  2. KDS
  3. Toy
  4. Chase 360
  5. Instruction Manual

KDS Chase 360 Instruction Manual

Summary of Chase 360

  • Page 1

    This radio controlled helicopter is not a toy! It has some technical requirements, you must pay attention to the flying environment and correct operation. Never fly your radio controlled helicopter over people or near crowds. Teenagers must fly under the guardian’s guide. Beginners must fly under th...

  • Page 2

    Page. 1 congratulations on your purchase of the chase 360 radio controlled helicopter kit. Chase 360 was designed in europe by australia by glen kimpton and is proudly manufactured by kds model. Our goal was to offer you something different with a minimum of parts, easy maintenance, and outstanding ...

  • Page 3

    Page. 2 proper operation please use the replacement of parts on the manual to ensure the safety of instructors. This product is for r/c model, so do not use for other purpose. Safe operation operate this unit within your ability. Do not fly under tired condition or improper operation, which may caus...

  • Page 4

    Page. 3 5.Equipment required for assembly radio transmitter and electronic equipment required for assembly 6.Package illustration •brushless electric motor: 6s lipo - 1900kv (3mm bolt holes, 25mm mount width, 4mm * 57.5mm motor shaft) •speed controller: minimum 50a (esc specs limits should be rated ...

  • Page 5

    200mm 688mm 90mm centre of gravity 96mm 814mm page. 4.

  • Page 6

    Page. 5 1 main belt ( 147mxl-9mm ) lower motor block 18t 2nd stage pinion 1st stage pulley pin 2 3 4 5 6 7 8 9 10 11 item no. Descrip tion qty. 1 1 2 8 3 1 4 1 5 1 6 1 7 2 8 9 10 11 1 1 1 1 round head screw(m2 . 5 x 6 ) bearing ( 4x10x4 ) motor mount bracket right motor mount bracket left upper moto...

  • Page 7

    0.5mm min 0.5mm min turn the motor over by hand to test belt positioning. Adjust the motor pinion height until the belt runs central on the front pulley make sure your motor has a flat ground on the shaft for the pinion grub screw. This step can be completed at any time. But is easier before install...

  • Page 8

    Bearing (3x7x3) belt guide pulley spacing washer gyro tray boom clamp 1 2 4 6 3 7 1 2 3 4 5 item no. Descrip tion qty. 1 1 2 4 3 2 4 2 5 1 6 4 7 2 item no. Descrip tion qty. 1 1 2 4 3 2 cap screw (m3 x 24 ) up pulley holder set spacer sleeve down pulley holder set flat head screw m2. 5x6 page. 7.

  • Page 9

    15mm nominal tip - it is best to position the servo arms on servos (with 0 trim) closest to level during this step . 6 4 long side of the brackets face clockwise. Cyclic servo lock nut ( m2 ) upper bearing block bearing ( 8x16x5 ) servo mount lower bearing block 1 2 3 4 5 6 7 1 2 item no. Descrip ti...

  • Page 10

    Recommended lipo 1200 - 1400 mah. Size restrictions 39mm x 45mm x 116mm. Or unlimited length with front tail servo mount option (refer to step 26) mirror this step for left side frame. Lipo tray button (right) side frame lipo 1200 - 1400mah 1 2 4 3 1 2 4 3 round head screw (m2 x 4 ) item no descrip ...

  • Page 11

    Item no descrip tion qty. 1 landing gear - left 1 2 landing gear - right 1 3 landing gear mount 2 4 from step 6 1 5 8 lock the screws only after main frame left is well-assembled. 1 2 3 4 5 cap screw (m2.5 x 10) page. 10

  • Page 12

    Frame spacers 2 lipo sliding rail ( right ) 1 round head screw (m2 x 4) 2 2 cap screw (m2.5 x 6) 5 1 2 3 item no. Descrip tion qty. 1 2 3 4 5 4 5 cap screw (m2.5 x 8) 6 frame washer (red) 7 6 page. 11.

  • Page 13

    1 2 4 3 5 6 ensure no free play in the tail shaft by fastening the locking collar and pinion against the bearings. Tail shaft tail shaft locking collar tail pinion ( 15t ) set screw ( m3x3 ) tail box bearings ( 4x8x3 ) 1 1 2 1 1 2 item no descrip tion qty. 1 2 3 4 5 6 page. 12.

  • Page 14

    Tip: tighten screws in a few stages to ensure the bracket remains parallel with the tail shaft. Refer to step 25 for details. Item no. Descrip tion qty. 1 fin spacer 1 2 tail boom 1 3 2 4 pitch slider bracket 1 5 tail belt 1 6 1 7 1 8 1 9 tail control guide 2 10 1 11 1 11 1 2 3 4 5 8 7 6 10 9 12 12 ...

  • Page 15

    Item no. Descrip tion qty. 1 parts from step 4 1 2 tail belt 1 3 parts from step 10 1 4 boom clamp 1 1 2 3 4 page. 14.

  • Page 16

    X2 item no. Descrip tion qty. 1 parts from step 5 1 2 parts from step 10 1 3 5 item no. Descrip tion qty. 1 front canopy mounting bolt 1 2 1 1 2 3 1 2 cap screw (m2.5 x 6) frame washer (red) 4 5 4 set screw (m2.5x10) page. 15.

  • Page 17

    Main shaft is symmetrical with no top or bottom. May be installed either way. Item no. Descrip tion qty. 1 one way bearing ( 10x14x6 ) 1 2 1 3 1 4 1 5 1 6 1 item no. Descrip tion qty. 1 parts from step 1 1 2 1 3 1 4 1 1 2 4 3 1 2 3 4 5 6 bearing ( 8x14x4 ) first reduction gear ( 80t ) bearing ( 10x1...

  • Page 18

    Item no. Descrip tion qty. 1 2 2 2 3 2 1 2 cap screw (m2.5 x 6) cap screw (m2.5 x 10) frame washer (red) page. 17 3.

  • Page 19

    1 item no. Descrip tion qty. 1 1 2 3 14 4 12 5 1 6 2 7 8 3 4 5 6 7 8 9 9 10 2 set screw (m2.5x10) frame washer (red) 1 rear canopy mounting bolt cap screw (m2.5 x 6) cap screw (m2.5 x 8) round head screw (m2 x 4) 1 lipo sliding rail left 1 cf front electronics board cap screw (m2.5 x 10) 1 4 side fr...

  • Page 20

    Note : factory pre-assembled item no. Descrip tion qty. 1 1 2 1 3 6 4 1 5 1 6 5 7 1 2 3 4 5 6 7 oscillating bearing swashplate internal linkage ball a swashplate outer ring swashplate mounting pin round head screw (m2 x 4) bearing ( 20x27x4 ) 1 page. 19.

  • Page 21

    1 9.8 10 larger id faces inwards . X2 2 3 4 5 6 7 1 2 3 4 bearings ( 2x5x2 . 5 ) cap screw (m2 x 10) 2 item no descrip tion qty. 1 2 3 4 5 6 7 8 9 10 11 2 item no descrip tion qty. 1 2 3 4 5 6 7 flybarless linkage arm flybarless swashplate control arm 6 5 7 8 9 10 11 8 2 2 2 2 main rotor holder bear...

  • Page 22

    X2 43mm 30mm x3 x2 43mm x3 item no. Descrip tion qty. 1 6 2 3 1 item no. Descrip tion qty. 1 4 2 4 3 2 item no. Descrip tion qty. 1 1 2 1 2 1 2 1 3 2 ball link a linkage rod (15mm) set screw (m2.5x10) ball link b linkage rod (15mm) lock nut ( m3 ) cap screw (m3 x 16) page. 21.

  • Page 23

    Item no. Descrip tion qty. 1 2 2 1 3 1 4 2 1 2 3 4 round head screw (m2 x 6) anti-rotation bracket 5 2 5 cap screw (m2.5 x 6) frame washer (red) anti-rotation bracket mount page. 22.

  • Page 24

    2 3 item no. Descrip tion qty. 1 2 2 4 3 2 4 2 5 2 item no. Descrip tion qty. 1 2 2 2 3 2 6 5 4 3 2 1 8 9 7 1 3 2 6 7 8 9 cap screw (m2 x 5) item no. Descrip tion qty. 2 1 2 2 bearings ( 3x6x2 . 5 ) thrust bearing ( f5 - 10m ) tail rotor holder linkage ball b washer ( 3 . 1x4 . 4x0 . 3 ) washer ( 2 ...

  • Page 25

    Note : factory pre-assembled item no. Descrip tion qty. 1 1 2 2 3 4 4 1 5 2 6 2 7 4 1 2 3 5 6 7 8 8 1 1 tail push bearing mount bearings ( 6x10x3 ) e - clip (1.5mm) t type arm ball link for tail holder pin tail push bearing set screw ( m3x3 ) page. 24.

  • Page 26

    90 check that the pitch slider fork is square to the shaft and the slider does not bind. Loosen bolts and adjust if required. 8 9 item no. Descrip tion qty. 1 2 2 1 3 1 4 1 5 2 item no. Descrip tion qty. 6 1 7 2 8 1 9 1 flange bearing (2x5x2.5) lock nut ( m2 ) linkage ball a cap screw (m2 x 4) tail ...

  • Page 27

    Rear servo mount option. Mini or micro servo front servo mount option. Micro servo only. 12mm nominal the chase 360 has 2 tail servo location options, at the front, high in the frame for 1. The lowest moment of inertia and optimal cg. 2. Under the tail boom at the rear of the frame. Item no. Descrip...

  • Page 28

    Screw reserved for boom brace installation build the tail pushrod to suit your desired servo location for rear mount servo extension for front mount servo page. 27.

  • Page 29

    Note :the boom brace may be mounted in multiple locations. 1 2 3 4 5 6 7 item no. Descrip tion qty. 1 2 2 4 3 4 4 2 5 1 6 1 7 2 tail boom brace tail boom brace end frame washer (red) cap screw (m2.5 x 8) cap screw (m2.5 x 6) tail boom brace mount cap screw (m2.5 x 10) page. 28.

  • Page 30

    Page. 29 parts list 1 pulley holder kc-360-016 2 x pulley holder 2 x main rotor holder arm main rotor holder arm kc-360-002 1 x main rotor head block housing 2 x main rotor paddle clip main rotor head block housing kc-360-003 main rotor paddle clip kc-360-004 second reduction gear mount kc-360-013 s...

  • Page 31

    Cf bottom plate kc-360-036 1 x cf bottom plate landing gear mount kc-360-040 2 x landing gear mount 1 x main gear 80t main gear 80t kc-360-031 tail belt 522mxl-4mm kc-360-026 1x motor pinion gear19t motor pinion gear18t kc-360-027-w motor pinion gear19t kc-360-028-w 1 x second reduction gear 18t sec...

  • Page 32

    Blade holder kc-360-059 1 x blade holder vertical stabilizer mount & pitch slider bracket kc-360-063 1 x vertical stabilizer mount & pitch slider bracket 1 x alu tail boom 425mm alu tail boom 425mm kc-360-054-l main frame mount kc-360-050 1x ball link set linkage ball set kc-360-051 ball link set kc...

  • Page 33

    1 x chase main blade 360mm chase main blade kc-360-078 bearing 3*7*3 kc-360-073 1x bearing 8*14*4 bearing kc-360-074 bearing kc-360-075 1 x bearing 10*15*4 bearing kc-360-077 1 x tall blade 62mm tall blade 62mm kc-360-079 bearing kc-360-076 1 x bearing 8*16*5 canopy kc-360-090 1 x canopy bearing kc-...

  • Page 34

    Page. 33 regular maintenance is required to keep the kds agile 5.5 helicopter in optimal and safe flying condition. The model requires precise configuration of the components and settings to be kept by the owner. Maintain regular maintenance on the model to avoid accidents or loss, and optimum perfo...

  • Page 35

    Version no ： 20150315 ... It's time to fly different!!!.