KEF Wireless 5000 series Installation Manual - page 6
Assembly to the KHT5000 speaker
Assembly to the Floorstand
i) Remove the speaker terminal screws from your KHT5000 speaker, place the supplied
contact pin holder on the terminal posts and then replace the terminal screws.
ii) Insert the supplied long bolt into the KHT5000 speaker foot screw hole.
iii) Slide the top of wireless receiver unit over the long bolt and then pressing it home
ensuring that the terminal contacts align with the wireless module socket.
The wireless receiver units have been pre-set for either left audio channel or right audio
channel. Refer to the small marking on the rear of the wireless receiver units to ensure
that the correct receiver unit is used for left or right speaker.
i) Insert the bolt provided into the bottom of the wireless receiver units to secure the
wireless module to the speaker and tighten.
ii) Insert the cable of AC-DC adaptor through the base of the floor stand such that the
plug can be connected to the DC Jack connector of wireless receiver unit.
iii) Assembly the complete wireless receiver units by aligning the rear and then the front
guides and pressing it down into the KHT5005 floor stand,
iv) Connect the AC-DC adaptor plug into the main AC socket. The wireless receiver
units will power-on and the blue bonding light on the front of the wireless module will
be flashing to show that the speaker is now ready to output audio when the
transmitter is powered on.
Assembly to the Desktop stand
i) Place the wireless receiver unit into the aluminium casing and screw the extension bolt
to the bottom of the aluminium casing.
ii) Assembly the metal foot to the casing and align the hole to the bolt accordingly.
Tighten the bolt with the nut provided at the bottom of the metal foot.
iii) Plug the AC-DC adaptor to the DC Jack connector of wireless receiver unit from the
hole provided underneath the aluminium casing.
iv) Connect the AC-DC adaptor plug into the main AC socket. The wireless receiver
units will power-on and the blue bonding light on the front of the wireless module will
be flashing to show that the speaker is now ready to output audio when the
transmitter is powered on.
Connecting to a KIT200 home
thereafter system
i)
Remove the transmitter speaker cable dongle
ii) Cut the rear left and rear right KIT200 speaker cable
iii) Screw in the left (colours) and the right (colours) speaker cables to the dongle
Connecting the Transmitter Unit
i) Power OFF all the A/V equipment during the installation of wireless system.
ii) Connect the supplied AC-DC adaptor to the DC Jack on the real panel of the
transmitter unit Connect the KEF Audio Jack connector to the key hole socket on the
real panel of the transmitter unit .
iii) Connect the speaker inputs to the rear LEFT speaker and rear RIGHT speaker
terminals of your AV receiver using the provided cable.
Rear left +
White
Rear left -
Black
Rear right +
Red
Rear right -
Blue
10
9
iv) Rotate the position of the transmitter unit such that the front panel is facing toward
the wireless speakers.
v) Connect the power supply to the mains socket and powered-on the transmitter by
pressing the power button on the front panel.
vi) Ensure that the blue bonding light is permanently on, this shows that the transmitter
unit and receiver units are successfully bonded and ready to output the audio. If the
bonding light is flashing, then check that both receiver units have been powered-on
and are within range.
vii) Power-on the audio source which are connected to the transmitter unit and adjust
the volume level accordingly from the remote control of the audio source.
Introduction
This wireless system is intended for use in home entertainment as left surround
speaker and right surround speaker. It can be assembled with the KHT5005 rear
speakers with either the floor stand or the desk top foot. It is for indoor use only.
Surround sound settings
Ensure that your AV receiver is set to 5.1 channel surround sound. If it has a calibra-
tion feature then this can be used to independently adjust the rear speaker volume lev-
els to compensate for your room. If there is an adjustable bass management setting
ensure that it is set to “small speakers” or with a crossover of approximately 80Hz.
The wireless system is specifically designed for audio and does not require any set up
what so ever. The correct receiver is required for the LEFT rear speaker and the RIGHT
rear speaker. Otherwise you only need to assemble the wireless module into the
speaker stand, plug it into the mains and switch them on.
KEF Wireless 5000 series manual 22/12/06 12:03 Page 10