Kelvinator KICT333HWF Instruction Booklet - page 5
16
SOMMAIRE
Avertissements et conseils importants
14
Renseignements pour l’élimination des
matériaux d’emballage
16
Utilisation
17
Nettoyage
17
Mise en service
17
Réglage de la température
17
Réfrigération
17
Securité alimentaire
18
Congélation
19
Conservation des produits surgelés
19
Décongélation
19
Glaçons
19
Tablettes amovibles
19
Positionnement des balconnets de la contre-
porte
19
Calendrier de congélation
20
Conseils
20
Conseils pour la réfrigération
20
Conseils pour la congélation
20
Conseils pour la surgélation
20
Entretien
21
Nettoyage
21
Arrêt prolongé
21
Changement de l’ampoule
21
Dégivrage
21
Anomalie de fonctionnement
22
Informations techniques
23
Installation
23
Emplacement
23
Arrêts pour clayettes
24
Entretoises postérieurs
24
Branchement électrique
24
Réversibilité des portes
25
RENSEIGNEMENTS POUR L’ÉLIMINATION
DES MATÉRIAUX D’EMBALLAGE
Tous les matériaux et les accessoires utilisés pour
emballer nos grands électroménagers, sauf ceux qui
sont en bois recyclables et peuvent donc se
récupérer.
Voici ce que nous vous conseillons:
•
Déposez les emballages en papier, en carton et
en carton ondulé aux endroits prévus pour le
ramassage de ce genre de matériau.
•
Mettez les piéces en plastique dans les
conteneurs prévus à cet effet.Si ce genre de
conteneurs n’existent pas encore à l’endroit où
vous habitez, vous pouvez éliminer les matériaux
en question en les mettant dans les ordures
ménagères.
Pour les emballages de matières plastiques
recyclables, par example:
Les exemples reportent les symboles suivants:
PE pour polyéthylène** 02 = ^ PE-HD; 04 = ^ PE-LD
PP pour le polypropylène
PS pour le polystyrène
PIÉCES EN MATIÈRE PLASTIQUE
Pour faciliter l’élimination et :ou le recyclage des
matériaux, la plupart des pièces de l’appareil ont
une contremarque qui en facilite l’indentification.
PS
SAN
ABS
02**
PE
05
PP
06
PS
45
CUSTOMER SERVICE AND SPARE PARTS
If the appliance is not functioning properly, check
that:
•
the plug is firmly in the wall socket and the mains
power switch is on;
•
there is an electricity supply (find out by plugging
in another appliance);
•
the thermostat knob is in the correct position.
•
If there are water drops on the bottom of the
cabinet, check that the defrost water drain
opening is not obstructed (see “Defrosting”
section).
•
If your appliance is still not working properly after
making the above checks, contact the nearest
service centre.
To obtain fast service, it is essential that when you
apply for it you specify the model and serial number
of your appliance which can be found on the
guarantee certificate or on the rating plate located
inside the appliance, on the bottom left-hand side.
However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried out
as follows:
1.pull out the plug from the wall socket or turn the
thermostat knob to the «O» setting;
2.remove any stored food, wrap it in several layers
of newspaper and put it in a cool place;
3.leave the door open.
4.when defrosting is completed, dry the interior
thoroughly;
5.turn the thermostat knob back to the required
setting or replace the plug in the power socket.
6.After two or three hours, reload the previously
removed food into the compartment.
Important:
Never use sharp metal tools to scrape off frost
from the evaporator as you could damage it.
Do not use a maechanical device or any artificial
means to speed up the thawing process other
than those recommended by the manufacturer.
A temperature rise of the frozen food packs,
during defrosting, may shorten their safe storage
life.