Küppersbusch IKE 160-2T Operating Instructions Manual

Manual is about: integrated refrigerator

Summary of IKE 160-2T

  • Page 1

    N/kü/1. (08.) 200381796 gebrauchs- und montageanleitung instructions for installation and use instructions de montage et d’emploi wichtig:unbedingt lesen und aufbewahren! Important:read these instructions carefully and then store them in a safe place important:lire attentivement et ranger soigneusem...

  • Page 2

    Instructions for the use of the instructions booklet notes which are important for your safety or for the proper functioning of the appliance supplementary information regarding operation and practical applications of the appliance. Tips and notes concerning economical and environmentally sound use ...

  • Page 3: Cont

    Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 diposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 4: Disposal

    Domestic use keep these instructions and they should remain at the appliance when moving away or changing owner. This appliance is designed for storing food, domestic use and being used according to these instructions only. Specialised companies that are qualified to do so by the manufacturer must c...

  • Page 5: Use and Control

    Use and control before use wait two hours before connecting the appliance to allow the oil to flow back in the compressor. Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a br...

  • Page 6: Hints

    Hints saving energy pay careful attention to where the cabinet is placed. See the section ŇinstallationÓ. When installed correctly the cabinet will consume less energy. Try to avoid keeping the doors open for long periods or opening the doors too frequently as warm air will enter the cabinet and cau...

  • Page 7

    Melting water flows through defrost water outlet into the evaporative tray maintained on the top of compressor and evaporates due to warmth of it. Check and clean the outlet of melting water coming during defrosting regularly. If it is clogged the melting water gathered can cause earlier failure as ...

  • Page 8: Something Not Working

    Something not working problems may be due to causes which can easily be solved before calling the technical service. Please follow these instructions: symptom door does not close it is too warm inside the refrigerator it is too cold inside the refrigerator. The compressor works continuously. There i...

  • Page 9: Door Reversibility

    Customer service and spare parts if you cannot find the remedy for a malfunction in these operating instructions, please contact your dealer or our customer service department and consult the guarantee card. Selective ordering of replacement parts can save unnecessary travel and costs. For this reas...

  • Page 10: Installation

    Climate for an ambient classification temperature of sn +10 to +32 °c n +16 to +32 °c st +18 to +38 °c t +18 to +43 °c electrical connection before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of...

  • Page 11: Building-In

    Attention! It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation. Building-in dimensions of the recess height of housing (1) 880 1225 mm depth of housing (2) 550 550 mm width of housing (3) 560 560 mm it is necess...

  • Page 12

    4. From the plastic cover (e), which is used to cover the hinge with the pivot pin, you must take away the part as indicated in the drawing. This operation is made easer since there is, in the internal part of the cover hinge lid a groove that facilates the removal of this coomponent. "remove the pa...

  • Page 13

    10. Place the small square on the guide again and fix it with the screws supplied. Should the alignment of the furniture door be necessary, use the clearance of slots. At the end of this procedure, it is necessary to check if the door of the furniture closes properly. 11. Fix cover (hd) on the small...