- DL manuals
- Küppersbusch
- Refrigerator
- IKE 4580-1-4T
- User Manual
Küppersbusch IKE 4580-1-4T User Manual
Summary of IKE 4580-1-4T
Page 1
Gebruiks- aanwijzing koel-vries- combinatie user manual fridge-freezer notice d'utilisation réfrigérateur- congélateur benutzer- information kühl-gefrier- schrank ike4580-1-4t.
Page 2: Safety
Contents safety instructions 23 control panel 25 first use 27 daily use 27 helpful hints and tips 30 care and cleaning 31 what to do if… 32 technical data 33 installation 34 environmental concerns 41 subject to change without notice. Safety instructions in the interest of your safety and to ensure t...
Page 3: Daily Use
If the refrigerant circuit should become damaged: – avoid open flames and sources of igni- tion – thoroughly ventilate the room in which the appliance is situated • it is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short- circuit, fire ...
Page 4: Service
• the appliance must not be located close to radiators or cookers. • make sure that the mains plug is accessi- ble after the installation of the appliance. • connect to potable water supply only (if a water connection is foreseen). Service • any electrical work required to do the servicing of the ap...
Page 5: Temperature Indicator
Temperature indicator during normal functioning the temperature indicator shows the temperature setting. Important! Difference between the temperature inside the compartment and temperature setting is normal. Especially when: • a new setting has recently been selected. • the door has been left open ...
Page 6: Supercool Function
Supercool function the maximum performance is obtained by setting the supercool function. It’s recom- mended when loading large quantities of food. You can activate the supercool function by pressing the supercool switch. The supercool light will light up. Important! The internal temperature goes do...
Page 7: Storage Of Frozen Food
Important! When use the fast freezing function: about 6 hours be- fore introducing small quantities of fresh food (about 5 kg) about 24 hours be- fore introducing the maximum quan- tity of food (see rating plate) not needed introducing frozen food not needed introducing small quantities of fresh foo...
Page 8: Movable Shelves
Movable shelves the walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired. For better use of space, the front half- shelves can lie over the rear ones. Fridge doors for proper opening and closing, it is advis- able to act on both doors simul...
Page 9: Superchill Compartment
Superchill compartment the temperature in this compartment (from 0°c to +3°c) is kept constant by a special sensor. No adjustment is needed. Products stored in this compartment will keep fresh and in peak condition. It is ad- visable to wrap foods in aluminium foil or plastic film. Drinks can be coo...
Page 10: Periodic Cleaning
• water ices, if consumed immediately after removal from the freezer compartment, can possibly cause the skin to be freeze burnt; • it is advisable to show the freezing in date on each individual pack to enable you to keep tab of the storage time. Hints for storage of frozen food to obtain the best ...
Page 11: Defrosting Of The Freezer
Defrosting of the freezer the freezer compartment of this model, on the other hand, is a "no frost" type. This means that there is no buildup of frost when it is in operation, neither on the inter- nal walls nor on the foods. The absence of frost is due to the continu- ous circulation of cold air in...
Page 12: Replacing The Lamp
Problem possible cause solution products prevent that water flows into the water collector. Make sure that products do not touch the rear plate. Water flows on the ground. The melting water outlet does not flow in the evaporative tray above the compressor. Attach the melting water outlet to the evap...
Page 13: Positioning
The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label. Installation positioning install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance: ...
Page 14: Fitting The Side Panels
870 mm 820 mm before installing the appliance between units, adjust the height of the feet and rear wheels. The wheels are factory set for a height of 820 mm. To align the appliance to a height of 870 mm, raise it by adjust- ing the feet with a spanner, then remove the wheels and refit them in the l...
Page 15
D d 1 2 d d 2 3 1 apply spacers to the hinges before instal- ling the appliance into the cabinet . See picture. 45 mm rest the panels against the appliance. Fit the rear brackets, taking into account the thickness of the panels (maximum width of unit 900 mm). For a correct alignment make sure that t...
Page 16: Fitting The Door Panels
N 90 o 115 o n l l if necessary, door opening angle max 90° can be obtained by introducing the pivots supplied separately. See picture. Fitting the door panels 2 1 10 mm open a door a remove the bracket cover. Undo the nuts with washers and remove the bracket from the door. 214 214 193 25 25 193 193...
Page 17
Fix the bracket to the door with the screws contained in the bag. 1 2 refit the bracket on the ad- justment screws and screw the nuts with washers with- out tightening them down. Close the door and check that the small door is posi- tioned at the required height, operating the adjustment screws if n...
Page 18: Building The Appliance In
1 2 3 fix the bracket located under the door to the panel with the two plastic washers con- tained in the box of accesso- ries. Then refit the bracket cover. Building the appliance in 1 2 fit the appliance into the recess. Rotate the bracket of 180° in order to ob- tain the right position ( 2). The ...
Page 19: Fitting The Plinth
50 mm 50 mm the top of the appliance must be kept clear to allow better air circulation. If a wall unit is fitted above the appliance, there must be a gap of 50 mm between this unit and the wall and it must be at least 50 mm below the ceiling. Fitting the plinth 140-190 mm 170-220 mm 30-100 mm 900 m...
Page 20
140-190 mm 1 2 3 if using a 100 mm plinth, fit the complete height compensation strip. 100-150 mm 30-100 mm alignment height of 870 mm if using a 190 to 220 mm plinth, make a shown. If using a plinth higher than 150 mm but less than 190 mm, cut the height compensation strip supplied with the applian...
Page 21
Product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local coun...
Page 22
85.
Page 23
86.
Page 24
87.
Page 25
222318846-b-112013.