1. DL manuals
  2. La Crosse Technology
  3. Weather Station
  4. WS-7016U
  5. Instruction Manual

La Crosse Technology WS-7016U Instruction Manual

Other manuals for WS-7016U: Instruction Manual, Instruction Manual
Manual is about: Wireless 433 MHz Temperature Station

Summary of WS-7016U

  • Page 1

    I ws-7054u wireless 433 mhz temperature station instruction manual.

  • Page 2

    Ii table of contents topic page inventory of contents 1 additional equipment 1 quick setup 2 detailed setup guide battery installation 3-6 remote control sender 3-4 indoor temperature station 5-6 setting the time 7-8 selecting units of measurement 8 features indoor minimum and maximum temperatures 9...

  • Page 3

    Iii remote control sender 13-16 indoor temperature station 16-18 using multiple remote control senders setup of multiple units 18-21 viewing remote control senders 21-22 features of the multiple remote control senders 22-23 troubleshooting 24-28 maintenance and care instructions 28-29 specifications...

  • Page 4

    1 inventory of contents 1. The indoor temperature station (figure 1) 2. The outdoor remote control sensor (tx3u) and mounting bracket. (figure 2) 3. 3 each, 1/2” philips screws. 4. One strip of double sided adhesive tape. 5. Instruction manual and warranty card. Additional equipment (not included) 1...

  • Page 5

    2 quick setup 1. Insert two aaa batteries into the remote control sender. 2. Insert two aa batteries into the indoor temperature station. 3. Wait 5-6 minutes, or until the outdoor temperature is displayed in the outdoor lcd (liquid crystal display) of the indoor temperature station. 4. Set the time ...

  • Page 6

    3 detailed setup guide i. Battery installation a. Remote control sender 1. Remove the mounting bracket. The bracket snaps on and off with minimal effort. 2. Remove battery cover. To do this, remove the flathead screw located in the lower-central position of the unit. The rubber weather-seal creates ...

  • Page 7

    4 battery cover to fall away from the unit. Place the screw partially back into the hole and angle it slightly, so the threads grab the battery cover. With the screw, pull the battery cover off. 3. Observing the correct polarity, install 2 aaa batteries. The batteries will fit tightly—make sure they...

  • Page 8

    5 b. Indoor temperature station note: after the batteries are installed, do not press any buttons. This may interfere with the signals, causing temperatures to register incorrectly. 1. Remove the battery cover on the backside. To do this, push up and pull out. Battery cover.

  • Page 9

    6 2. Observing the correct polarity, install 2 aa batteries. 3. Replace battery cover. 4. Wait 5-6 minutes or until both indoor and outdoor temperatures are shown on the indoor temperature station. 5. The indoor temperature station should now show: “-:- -” in the time lcd, and temperatures in the in...

  • Page 10

    7 ii. Time a. Setting the time 1. Press and hold the set button for 1 second. “12h” will appear in the time lcd. 2. Use the indoor button to select either 12h time or 24h time (12h is an am—pm mode, and 24h is military time). 3. Press the set button 2 times, “time” will flash in the upper left corne...

  • Page 11

    8 5. Press the set button to activate the clock. Note: there is only a “pm” display, which appears under “time.” if there is no display here it is am. Make sure you set the time accordingly. Iii. Units of temerature measure a. Selecting units of measurement 1. Press and hold the set button for 1 sec...

  • Page 12

    9 iv. Features a. Indoor minimum and maximum temperatures 1. Press and hold the indoor button for 1 second. “min” appears in the indoor lcd and the recorded minimum temperature is displayed. 2. Press and hold the indoor button for 1 second. “max” appears in the indoor lcd and the recorded maximum te...

  • Page 13

    10 b. Outdoor minimum and maximum temperatures 1. Press and hold the outdoor button for 1 second. “min” appears in the outdoor lcd. The “outdoor min,” and “time” displays will flash. The recorded minimum temperature is displayed in the outdoor lcd, and the time it was recorded is displayed in the ti...

  • Page 14

    11 displayed in the outdoor lcd, and the time it was recorded is displayed in the time lcd. After 15 seconds the “outdoor max,” and “time” will stop flashing, and the maximum outdoor temperature will continue to be displayed. 3. To return to current temperature, press and hold the outdoor button for...

  • Page 15

    12 temperatures are reset release the buttons. 2. To return to the current indoor temperature, press and hold the indoor button two times, holding for 1 second each. B. Outdoor 1. To reset both the minimum and maximum temperatures—press and continue to hold the outdoor button, while you press and ho...

  • Page 16

    13 vi. Reading the temperature trend a. The temperature trend indicator is displayed in the outdoor lcd. 1. Ï indicates that the temperature is rising. 2. Ð indicates that the temperature is dropping. 3. The absence of an arrow indicates that the temperature is stable. Vii. Mounting a. The remote co...

  • Page 17

    14 walls, concrete, and large metal objects can reduce the range. Place both units in their desired location before permanently mounting the remote control sender. There should be a change of temperature in the outdoor lcd within 6 minutes. The remote control sender can be mounted in two ways: • wit...

  • Page 18

    15 c) where marked, drill holes into mounting surface using an appropriate size drill bit. D) screw mounting bracket onto the mounting surface. Ensure that the screws are flush with the bracket. 2. Mounting with adhesive tape a) with a nonabrasive solution, clean and dry the back of the mounting bra...

  • Page 19

    16 c) remove the protective strip from the other side of the tape. Position the remote control sender in the desired location, ensuring that the indoor temperature station can receive the signal. B. The indoor temperature station note: before mounting the indoor temperature station make sure that it...

  • Page 20

    17 1. Using the table-stand a) the indoor temperature station comes with the table stand already mounted. If you wish to use the table- stand all that is required is to place the indoor temperature station in an appropriate location. 2. Wall mounting.

  • Page 21

    18 a) remove the table stand. To do this, pull down on the stand from the rear and rotate forward. B) fix a screw (not included) into the desired wall, leaving approximately 3/16 of an inch (5mm) extended from the wall. C) place the indoor temperature station onto the screw using the hanging hole on...

  • Page 22

    19 offers the same plus a 10’ probe to insert in a pool, spa, soil, etc.). Assign a number to each remote control sender (i.E. #1 will be for outdoors, #2 will be for the basement, etc.). This will help you determine which temperature, from which sender, you are reading on the indoor temperature sta...

  • Page 23

    20 a. Setup of multiple units 1. It is necessary to remove the batteries from all existing units in operation. 2. Remove the battery covers to all remote control senders. See section i.A.2. 3. Place all remote control senders in sequential order. 4. In sequential order, install batteries. (refer to ...

  • Page 24

    21 1 5. Install batteries into the indoor temperature station. (refer to instructions in i.B. ). 6. Follow directions in section ii.A to set the time, section iii.A to select fahrenheit or celsius, and section vii. A to mount. B. Viewing multiple remote control senders on the indoor temperature stat...

  • Page 25

    22 3. Repeat step 1 to view the 3 rd , 4 th , and 5 th (depending on how many are set up) temperatures sent by the remote control senders. Continue to press reset until you return to the first remote control sender. C. Viewing the features of multiple remote control senders 1. Press the reset button...

  • Page 26

    23 their minimum and maximum temperatures. 3. To reset the outdoor minimum and maximum temperatures, follow step 1 above and the directions in sections v.A. Through v.B. This will reset the minimum and maximum for only the selected remote control sender..

  • Page 27

    24 troubleshooting problem solution “--. -” appears in the outdoor lcd of the indoor temperature station. Batteries may be inserted wrong in remote control sender— correct the polarity the batteries may be weak— replace with new batteries. The remote control sender may be out of its 80 foot (25m) ra...

  • Page 28

    25 “--.-” appears in the outdoor lcd of the indoor temperature station. (continued) obstacles such as walls, concrete, metal window frames, or large metal objects, may be obstructing signal transmission from the remote control sender—relocate the remote control sender, within range, where there are ...

  • Page 29

    26 no temperature in the lcd of the remote control sender. The batteries may be inserted wrong or weak—check the polarity of batteries or replace with new batteries. Remote control sender out of its 80 foot (25m) range—bring the units closer together. If problem persists contact la crosse technology...

  • Page 30

    27 the lcd of the indoor temperature station is blank. (continued) contact la crosse technology for replacement. Temperature is “incorrect” temperatures can vary depending on the location of the remote control sender. The thermometers are not 100% accurate (the ws-7054u is accurate to +/- 2 ° f). If...

  • Page 31

    28 problem not covered under the warranty (ie. Dropped unit into water). Call la crosse technology to order replacement part. We will accept visa, mastercard, discover, or prepayments by check. Maintenance and care instructions • extreme temperatures, vibration, and shock should be avoided to preven...

  • Page 32

    29 • opening the casings invalidates the warranty. Do not try to repair the unit. Contact la crosse technology repairs. Specifications transmitting frequency 433mhz recommended operating temperature indoor temperature station 32 ° f to 122 ° f (0 ° c to 50 ° c) remote control sender 14 ° f to 140 ° ...

  • Page 33

    30 with 0.2 ° f resolution. (-29.9 ° c to 69.0 ° c with 0.1 ° c resolution). Accuracy indoor +/- 2 ° f (+/- 1 ° c). Outdoor +/- 2 ° f (+/- 1 ° c). Transmitting range of the remote control sender maximum 80 feet (25m). Temperature check indoor temperature station: indoor every 10 seconds. Indoor temp...

  • Page 34

    31 indoor temperature station 3.51 x 1.19 x 4.88 in. (excluding table stand) (90 x 30.5 x 125 mm). Remote control sender 2.18 x 0.94 x 3.12 in. (56 x 24 x 80 mm). Warranty information la crosse technology, ltd provides a 1-year limited warranty on this product against manufacturing defects in materi...

  • Page 35

    32 herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of la crosse technology, ltd and must be returned to la crosse technology, ltd. Replacement parts and products assum...

  • Page 36

    33 other than an authorized la crosse technology, ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference.. This warranty covers only actual ...

  • Page 37

    34 for warranty work, technical support, or information contact: la crosse technology 2809 losey blvd. S. La crosse, wi 54601 phone: 608.782.1610 fax: 608.796.1020 e-mail: support@lacrossetechnology.Com (warranty work) sales@lacrossetechnology.Com (information on other products) web: www.Lacrossetec...

  • Page 38

    35 fcc disclaimer this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Freq. ...