1. DL manuals
  2. La Crosse Technology
  3. Weather Station
  4. WS-7107U
  5. Instruction Manual

La Crosse Technology WS-7107U Instruction Manual

Manual is about: Wireless 433 MHz Weather Station

Summary of WS-7107U

  • Page 1

    Ws-7107u wireless 433 mhz weather station instruction manual.

  • Page 2: Table of Contents

    2 table of contents topic page inventory of contents 3 additional equipment 4 quick setup 5-8 detailed setup guide battery installation 9-11 setting the weather station 11-12 features minimum and maximum temperatures 13 resetting minimum and maximum temperatures 14 adding additional remote temp/humi...

  • Page 3: Inventory of Contents

    3 inventory of contents 1. Two indoor weather station (figure 1) 2. The remote temperature/humidity sensor (tx7u) and mounting bracket. (figure 2) 3. Mounting hardware. 4. Instruction manual and warranty card. Figure 1 figure 2.

  • Page 4: Additional Equipment

    4 additional equipment (not included) 1. 1 philips screwdriver. 2. 2 fresh aa 1.5v batteries. (for indoor weather station) 3. 2 fresh aa 1.5v batteries. (for temp/humidity sensor).

  • Page 5: Quick Setup

    5 quick setup hint: use good quality alkaline batteries and avoid rechargeable batteries. 1. Have the indoor weather station and remote temp/humidity sensor 3 to 5 feet apart. 2. Batteries should be out of all units for 10 minutes. 3. Place the batteries into the remote temp/humidity sensor first, t...

  • Page 6

    6 weather station does not display both the indoor temperature and the outdoor temperature and humidity after the 15 minutes please retry the set up as shown on page five. After both indoor temperature and outdoor temperature and humidity are displayed for 10 minutes you can place your remote temp/h...

  • Page 7

    7 interior wall can have up to 20 feet of resistance. Your distance plus resistance should not exceed 330 ft. In a straight line. To complete the set up of your indoor weather stations after the 10 minutes have passed, please follow the steps below. 1. Press and hold the “set” button for two seconds...

  • Page 8: Detailed Setup Guide

    8 battery compartment am hours this area will be blank. Press and release the set button three more times and your time is set. Note: there is also a setting for the temperature measuring unit and 12/24- hour time. Please see the detailed set-up section for more details on these settings. Detailed s...

  • Page 9: Indoor Weather Station

    9 1. Remove battery cover 2. Observing the correct polarity, install 2 aa batteries—make sure they do not spring free, or start-up problems may occur. 3. Replace cover. B. Indoor weather station note: after the batteries are installed, do not press any buttons for 15 minutes. This may interfere with...

  • Page 10: II.

    10 3. Replace battery cover. 4. Wait 15 minutes or until both the indoor and outdoor temperatures are shown on the indoor weather station. 5. The indoor weather station should now show: “-:- -” in the time lcd, indoor temperature in the indoor lcd and outdoor temperature and humidity in the outdoor ...

  • Page 11

    11 3. Press and release the “+” button to advance to your desired minutes. 4. Press and release the “set” button to move to the hour setting. 5. The hours will begin to flash. 6. Press and release the “+” button to set the hour. 7. Press and release the “set” button to move to the temperature measur...

  • Page 12: Features

    12 setting mode. Note: when in the 12-hour time mode “pm” is displayed to the left of the hour when between noon and midnight. During the am hours this area will be blank. Features a. Minimum and maximum temperatures 1. Press and release the “min/max” button. “min” appears at the bottom of the displ...

  • Page 13: Resetting The Minimum and

    13 2. Press and release the “min/max” button to toggle to the minimum temperatures, “max” appears at the bottom of the display and the recorded maximum temperatures are displayed. B. Resetting the minimum and maximum temperatures to reset both the minimum and maximum temperatures—press and hold the ...

  • Page 14

    14 set-up of remote sensor units with the ws-7107u. These extra sensors can be purchased through the same dealer as this unit, or by contacting la crosse technology directly. A tx6 will monitor temperature only, a tx3u will monitor temperature and display the temperature on its lcd, the tx3up will m...

  • Page 15

    15 1. It is necessary to remove the batteries from all units currently in operation. 2. Remove the battery covers to all remote sensor units. 3. Place all remote sensor units in a numeric sequential order. 4. In sequential order, install batteries (follow the same battery installation procedures see...

  • Page 16: Viewing and Operating

    16 d. Viewing and operating with multiple remote sensor units 1. To view the temperature of a different remote sensor unit, press and release the “ch” button. A shift from one “boxed” number to the next should be observed in the outdoor lcd. 2. To view the minimum/maximum temperature: first select f...

  • Page 17: Mounting

    17 3. To reset the minimum/maximum readings, press and hold the “min/max” button for five seconds. Mounting note: to achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temp/humidity sensor on an outside north- facing wall. The sending range ...

  • Page 18: The Weather Station

    18 3. Reattach the remote temp/humidity sensor to the mounting bracket. B. The weather station 1. The indoor weather station comes with the table stand already mounted. If you wish to use the table-stand, all that is required is to place the indoor weather station in your desired location. 2. To wal...

  • Page 19: Troubleshooting

    19 troubleshooting note: for problems not solved, please contact la crosse technology via e-mail or phone, or visit our website, www.Lacrossetechnology.Com problem: the lcd is faint solution: replace batteries problem: no outdoor temperature or humidity is displayed. Solution: 1) first try to re-est...

  • Page 20

    20 3) once the system has been reset and you have a temperature and humidity reading from the sensor, temporarily place the remote temp/humidity sensor in the previous location. Note: if there is an outdoor temperature and humidity displayed when the two units are close together there was either too...

  • Page 21

    21 problem: temperatures do not match if units are placed next to each other. Solution: each temp/humidity sensor is manufactured to be accurate to within 2 degree plus or minus and under normal conditions. It is possible for two temp/humidity sensors to be as much as 4 degrees different. The differ...

  • Page 22: Maintenance and Care

    22 compensate for the above factors and obtain an accurate comparison. Maintenance and care instructions • extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may...

  • Page 23: Specifications

    23 specifications transmitting frequency 433mhz measuring range - temperature indoor weather station: indoor 32 °f to 138.2°f (0.0 °c to 59°c) with 0.2 °f (0.1°c) resolution. Indoor weather station: outdoor -22 °f to 157.8°f (-29.9 °c to 69.9°c) with 0.2 °f (0.1°c) resolution. Measuring range - humi...

  • Page 24: Dimensions:  (H X W X D)

    24 remote temp/humidity sensor 2 x aa, 1.5v indoor weather station 2 x aa, 1.5v dimensions: (h x w x d) indoor weather station 5.66 x 3.38 x 1.16 inches (144 x 86 x 29.5 mm) remote temp/humidity sensor 6.29 x 1.69 x 0.9 inches (160 x 43 x 23 mm) battery life approximately 1 year.

  • Page 25: Warranty Information

    25 warranty information la crosse technology, ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in north america and only to th...

  • Page 26

    26 or if a product is examined which is not in need or repair, you will be charged for the repairs or examination. The owner must pay any shipping charges incurred in getting your la crosse technology, ltd product to a la crosse technology, ltd authorized service center. La crosse technology, ltd wi...

  • Page 27

    27 misrepresentation by the seller or performance variations resulting from installation-related circumstances. La crosse technology, ltd will not assume liability for incidental, consequential, punitive, or other similar damages associated with the operation or malfunction of this product. This pro...

  • Page 28

    28 (warranty work) sales@lacrossetechnology.Com (information on other products) web: www.Lacrossetechnology.Com fcc disclaimer this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device...

  • Page 29

    29 all rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or processed using electronic, mechanical or chemical procedures without written permission of the publisher. This handbook may contain mistakes and printing errors. The information in this hand...