- DL manuals
- La Crosse Technology
- Weather Station
- WS-7136U
- Instruction Manual
La Crosse Technology WS-7136U Instruction Manual
Summary of WS-7136U
Page 1
Ws-7136u wireless 433 mhz temperature station instruction manual.
Page 2: Table of Contents
2 table of contents topic page inventory of contents 3 additional equipment 4 quick setup 5-9 detailed setup guide battery installation 10-12 setting the time format 13 setting the temp. Format 13-14 setting the time 14-15 features minimum and maximum temperatures 16-17 resetting minimum and maximum...
Page 3: Inventory of Contents
Inventory of contents 1. The indoor temperature station (figure 1) 2. The remote temperature sensor (tx6u) and mounting bracket. (figure 2) 3. Mounting hardware. 4. Instruction manual and warranty card. 3 figure 1 figure 2.
Page 4: Additional Equipment
4 additional equipment (not included) 1. 1 philips screwdriver. 2. 2 fresh aaa 1.5v batteries. (for the indoor temperature station) 3. 2 fresh aa 1.5v batteries. (for the temperature sensor).
Page 5: Quick Setup
5 quick setup hint: use good quality alkaline batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of all units for 10 minutes. 3. Place the batteries into the remote temperature sensor first, t...
Page 6
6 in this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both the indoor temperature and the outdoor temperature af...
Page 7
7 notes on outdoor sensor placement the remote temperature sensor should be placed in a dry, shaded area. Fog and mist will not harm your remote temp/humidity sensor but direct rain must be avoided. The remote temperature sensor has a range of 80 feet. Any walls that the signal will have to pass thr...
Page 8
8 to complete the set up of your indoor temperature station after the 15 minutes have passed, please follow the steps below. 1. Press and hold the “set” button for 5 seconds. Note: a “12h” or “24h” will appear on the top line. (“12h” for am/pm, “24h” for military time) a. To change between “12h” and...
Page 9: Note: When In The 12H Mode
9 and release the “set” button once. 3. An hour will now be flashing. A. Press and release the “reset/+” button until the correct hour is shown. Note: when in the 12h mode “pm” is displayed in the upper left corner of the display between noon and midnight. During the am hours this area will be blank...
Page 10: Detailed Setup Guide
Detailed setup guide i. Battery installation a. Remote temperature sensor battery compartment 1. Remove the mounting bracket. Battery cover 2. Remove battery cover. 3. Observing the correct polarity, install 2 aa batteries—make sure they do not spring free, or start-up problems may occur. 4. Replace...
Page 11: Indoor Temperature
B. Indoor temperature station note: after the batteries are installed, do not press any buttons for 15 minutes. This may interfere with the signals, causing temperatures to register incorrectly. 1. Remove the battery cover on the backside. To do this, push up and pull out. 2. Observing the correct p...
Page 12: II.
Indoor temperature in the indoor lcd and outdoor temperature in the outdoor lcd. Ii. Programming sequence the programming sequence and default (factory) settings for the indoor temperature station is as follows: 1. Time format (default 12h) 2. Temperature format (default °f) 3. Time-hour (default 12...
Page 13: III.
Iii. Setting the time format 1. Press and hold the “set” button for 5 seconds. 2. “12:h” will begin to flash. 3. Press and release the “reset/+” button to select your desired time format. 4. Press and release the “set” button to advance to the temperature format setting or wait 15 seconds for the di...
Page 14: Setting The Time
5. Press and release the “reset/+” button to select your desired temperature format. 6. Press and release the “set” button to advance to the time setting or wait 15 seconds for the display to return to the normal mode. V. Setting the time 1. Press and hold the “set” button for 5 seconds. 2. “12:h” w...
Page 15
15 move to the minute setting. 7. The minutes will begin to flash. 8. Press and release the “reset/+” button to set the minutes. 9. Press and release the “set” button to advance to the time setting or wait 15 seconds for the display to return to the normal mode. Note: there is “pm” displayed to the ...
Page 16: Features
Features a. Minimum and maximum temperatures 1. Press and release the “min/max” button, “min” appears above and to the right of each temperature and the recorded minimum temperatures are displayed along with the time of the recorded minimum outdoor temperature. 2. Press and release the “min/max” but...
Page 17: Resetting The Minimum and
17 temperature and the recorded maximum temperatures are displayed along with the time of the recorded maximum outdoor temperature. Please note that the flashing time is the time of the recorded outdoor temperature minimum or maximum. B. Resetting the minimum and maximum temperatures to reset both t...
Page 18
18 additional remote sensor units with the ws-7136u. These extra sensors can be purchased through the same dealer as this unit, or by contacting la crosse technology directly. A tx6u will monitor temperature only, a tx3u will monitor temperature and display the temperature on its lcd, the tx3up will...
Page 19
19 1. It is necessary to remove the batteries from all units currently in operation. 2. Remove the battery covers to all remote sensor units. 3. Place all remote sensor units in a numeric sequential order. 4. In sequential order, install batteries (follow the same battery installation procedures see...
Page 20: Viewing and Operating
D. Viewing and operating with multiple remote sensor units 1. To view the temperature of a different remote sensor unit, press and release the “ch” button. A shift from one “boxed” number to the next should be observed in the outdoor lcd. 2. To view the minimum/maximum temperature: first select from...
Page 21: Mounting
21 mounting note: to achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sensor on an outside north- facing wall. The sending range is 80ft; obstacles such as walls, concrete, and large metal objects will reduce the range. Place b...
Page 22: The Temperature Station
22 b. The temperature station 1. The indoor temperature station comes with the table stand already mounted. If you wish to use the table-stand, all that is required is to place the indoor weather station in your desired location. 2. To wall mount: a) remove the table stand by pulling down on the sta...
Page 23: Troubleshooting
23 troubleshooting note: for problems not solved, please contact la crosse technology via e-mail or phone, or visit our website, www.Lacrossetechnology.Com problem: the lcd is faint solution: replace batteries problem: no outdoor temperature is displayed. Solution: 1) first try to re-establish commu...
Page 24
24 3) once the system has been reset and you have a temperature reading from the sensor, temporarily place the remote temperature sensor in the previous location. Note: if there is an outdoor temperature displayed when the two units are close together there was either too much distance between the t...
Page 25
25 problem: temperatures do not match if units are placed next to each other. Solution: each temperature sensor is manufactured to be accurate to within 2 degree plus or minus and under normal conditions. It is possible for two temperature sensors to be as much as 4 degrees different. The difference...
Page 26: Maintenance and Care
26 compensate for the above factors and obtain an accurate comparison. Maintenance and care instructions • extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may...
Page 27: Specifications
27 specifications transmitting frequency 433mhz measuring range - temperature indoor temperature station: indoor 32 °f to 140°f with 0.1°f resolution. Indoor temperature station: outdoor -21.8 °f to 156.2°f with 0.1 °f resolution. Temp accuracy +/- 2 °f temperature checking interval indoor: every 10...
Page 28: Dimensions: (H X W X D)
28 indoor temperature station 2 x aaa, 1.5v dimensions: (h x w x d) indoor temperature station 4.75” x 3.15” x 0.85” (excluding table stand) (120 x 80 x 21.8 mm) remote temperature sensor 5.04” x 1.57” x 0.9” (128 x 40 x 23 mm) battery life approximately 1 year.
Page 29: Warranty Information
29 warranty information la crosse technology provides a 1-year warranty on this temperature station. Contact la crosse technology immediately upon discovery of any defects covered by this warranty. Before sending the temperature station in for repairs, contact la crosse technology. The temperature s...
Page 30: Fcc Disclaimer
30 may also have other rights specific to your state. Some states do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information contact la crosse technology 190 main street la cr...
Page 31: Fcc Id: Omo-01Rx (Receiver)
31 this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Freq. 433.92 mhz la c...