Ws-7208u wireless 433 mhz weather station instruction manual.
2 table of contents topic page quick setup 3-5 inventory of contents 6-7 detailed setup guide battery installation 8 setting the time 9 features minimum and maximum temperatures 10 resetting minimum and maximum temperatures 11 adding additional remote temperature sensors (optional) 12-13 weather for...
3 quick setup hint: use good quality alkaline batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first t...
4 display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displayed for 10 minutes you can place your re...
5 note: fog and mist will not harm your remote temperature sensor but direct rain must be avoided. To complete the set up of your indoor temperature station after the 10 minutes have passed please follow the steps in the detailed set up guide on page 8-9. Inventory of contents 1. The indoor weather ...
6 additional equipment (not included) 1. 1 philips screwdriver. 2. 2 fresh aa alkaline batteries. 3. 2 fresh aa alkaline batteries detailed setup guide battery installation figure 2 holder figure 1.
7 1. Install 2 aa batteries in the remote temperature sensor. Make sure they do not spring free, or start-up problems may occur. 2. Install 2 aa batteries in the indoor weather station. Do not press any buttons for at least ten minutes. Setting the time 1. Press and hold the “set” key for 4 seconds....
8 6. Press and release the “+” key to advance the minutes. 7. Press and release the “set” key to exit programming. Features minimum and maximum temperatures 1. Press and release the “min/max” button, “max” appears between the indoor and remote temperatures. 2. The recorded maximum indoor and remote ...
9 while viewing the minimum or maximum temperatures. Resetting min and max temperatures to reset both the minimum and maximum temperatures—press and hold the “min/max” button for 5 seconds. Adding additional remote temperature sensors (optional) the ws-7208u is able to receive signals from 3 differe...
10 on its lcd, and the tx3up will monitor the temperature of water or soil via a probe. When setting up multiple remote temperature sensors, it is important to remove the batteries from all existing units in operation, then to insert batteries first into all the remote temperature sensors. Second in...
11 over time. The ws-7208uf averages past air-pressure readings to provide an accurate forecast, creating a necessity to disregard all weather forecasting for 12-24 hours after the unit has been set-up, reset, or moved from one altitude to another (i.E. From one floor of a building to another floor)...
12 sunny —indicates that the weather is expected to improve (not that the weather will be sunny). Sun with clouds — indicates that the weather is expected to be fair (not that the weather will be sunny with clouds). Clouds with rain — indicates that the weather is expected to get worse (not that the...
13 occur quickly. If the symbols do not change then the weather has not changed, or the change has been slow and gradual. Weather tendency arrows other possible displays in the forecast lcd are 2 weather tendency arrows, one that points up (on the left side of the lcd) and one that points down (on t...
14 the sending range is 80ft; obstacles such as walls, concrete, and large metal objects will reduce the range. Place both units in their desired location before permanently mounting. Remote temperature sensor remove the mounting bracket from the remote temperature sensor. Mount the bracket in the d...
15 using the integrated hanging hole on the back of the unit, slip indoor weather station over the screw and pull down to secure. Troubleshooting note: for problems not solved, please contact la crosse technology via e-mail or phone, or visit our website, www.Lacrossetechnology.Com problem: the lcd ...
16 straight-line signal is not passing through more than two or three walls. Problem: temperatures do not match if units are placed next to each other. Solution: each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions, so two sensors could ...
17 is difficult to compensate for the above factors and obtain an accurate comparison. Maintenance and care instructions • extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • clean displays and units with a soft, damp cloth. Do not use solvents or scouring ...
18 specifications transmitting frequency 433mhz measuring temperatures indoor weather station 32 ° f to 156.2 ° f with 0.2 ° f resolution (0 ° c to 69.0 ° c with 0.1 ° c resolution) remote temperature sensor -21.8 ° f to 156.2 ° f with 0.2 ° f resolution (-29.9 ° c to 69.0 ° c with 0.1 ° c resolutio...
19 indoor weather station 2 x aa, 1.5v dimensions: (l x w x h) indoor weather station 2.90 x 1.05 x 6.20 in. Remote temperature sensor 1.57 x 0.85 x 5.00 in. Battery life approximately 1 year warranty information la crosse technology provides a 1-year warranty on this indoor weather station. Contact...
20 batteries, or the indoor weather stations inability to receive a signal due to any source of interference. La crosse technology will not assume liability for incidental, consequential, punitive, or other similar damages associated with the operation or malfunction of this indoor weather station. ...
21 e-mail: support@lacrossetechnology.Com (warranty work) sales@lacrossetechnology.Com (information on other products) web: www.Lacrossetechnology.Com fcc disclaimer this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not caus...
22 fcc id: omo-01rx (receiver), omo-01tx (transmitter) this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept interference received, including interference that may ca...