All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or processed using electronic, mechanical or chemical procedures without written permission of the publisher. This handbook may contain mistakes and printing errors. The information in this handboo...
Battery compartment lcd display function keys weather projection station instruction manual introduction: congratulations on purchasing this state-of-the-art weather projection station as an example of innovative design and quality piece of engineering. Providing radio controlled time, date, calenda...
• wwvb radio controlled time with manual setting option • time reception on/off (user selectable) • 12/24 hour time display • dst on/off (daylight saving time) • us time zone map • time zone option ±12 hours • month, date, weekday calendar display • alarm setting with snooze function • automatic day...
To install and replace batteries in the weather projection station the weather projection station uses 3 x aa, iec lr6, 1.5v batteries. To install and replace the batteries, please follow the steps below: 1. Insert finger or other solid object in the space at the bottom center of the battery compart...
Battery installation: 1. First, insert the batteries into the weather projection station (see “to install and replace batteries in the weather projection station”). Once the batteries are in place, all segments of the lcd will light up briefly and a short signal tone will sound. Then the alm1 6:00, ...
If the batteries are used as the main power source: 1. Projected image brightness, alarm volume and back-light strength will be weaker when batteries are low 2. Battery life time will be much less than 1 year; depending on the frequency of projection and alarm. To use the projector power adapter the...
Sensors in the order of set-up, i.E. The first sensor will have the temperature/humidity displayed with the number 1 against it and so on. 5. With less than 3 sensors received, the weather projection station will try to pick up the remaining one in approximately another 3 minutes. If 3 sensors are r...
Up the weather projection station again. Proceed from step 1 in “setting up”,“battery installation” or “how to use the projector adaptor”. How to use the projector the projector projects the current time and the current outdoor temperature onto the ceiling, preferable within a darkened room. The pro...
Alarm 1 key hour/in key min/out key alarm 2 key direction key set key ch/+ key displ key snooze key as 9,192,631,770 vibrations of a cesium-133 atom in a vacuum. For more detail, visit http://www.Boulder.Nist.Gov/timefreq.Htm. To listen to the nist time, call (303)499-7111. This number will connect ...
Set key • enter manual setting modes: lcd contrast, time zone, dst on/off, time reception on/off, 12/24 hour display, manual time setting, calendar, snooze function, temperature °f or °c, and weather icon sensitivity setting • stop the alarm during alarm ringing • stop snooze mode • back-light on ch...
Moon phase icon alarm time weather tendency indicator time calendar display indoor relative humidity in rh% time reception icon (for wwvb time) alarm icon indoor temperature in ºf/ ºc weather forecast icon outdoor data signal reception indicator outdoor temperature in ºf/ ºc outdoor sensor identific...
Manual settings: the following manual settings can be changed when pressing the set key for: • lcd contrast setting • time zone setting • dst (daylight saving time) setting • time reception on/off setting • 12/24-hour setting • manual time setting • calendar setting • snooze setting • °f/°c setting ...
Dst (daylight saving time) setting: note: the dst default is “on”, meaning that the received time will automatically be adjusted according to daylight saving time in the spring and fall. For areas that do not recognize dst changes (arizona and parts of indiana) turn the dst “off”. 1. The digit “on” ...
Manual time setting: in case the weather projection station cannot detect the wwvb-signal (for example due to disturbances, transmitting distance, etc.), the time can be manually set. The clock will then work as a normal quartz clock. 1. The hour digit will start flashing. 2. Use the ch/+ key to set...
Icons flashing snooze setting: the snooze time can be set off to a maximum time of 30 minutes (default is 10 minutes): 1. Use the ch/+ key to set the snooze time. Each pressing of the key will increase the snooze time by 5 minutes. The snooze can also be set off when the “off” digit is being display...
Alarm setting: the alarm time can be set when pressing the alarm 1 or alarm 2 key. 1. Press the alarm 1 or alarm 2 key until the alarm digits flash. 2. Use the hour/in key to set the alarm hour. 3. Use the min/out key to set the alarm minute. 4. Confirm with the alarm 1, alarm 2, or snooze key and e...
New moon full moon small waxing crescent large waning gibbous large waxing crescent small waning gibbous first quarter last quarter small waxing gibbous large waning crescent large waxing gibbous small waning crescent moon tide: the moon tide information is indicated on the left side of the moon pha...
The icons displayed forecasts the weather in terms of getting better or worse and not necessarily sunny or rainy as each icon indicates. For example, if the current weather is cloudy and the rainy icon is displayed, it does not mean that the product is faulty because it is not raining. It simply mea...
Indoor relative humidity and indoor temperature: the indoor temperature and humidity data, the indoor comfort indicator are automatically updated and displayed on the fourth section of the lcd. The comfort level indicator: comfortable: a happy face icon “ ☺” indicating a temperature level between 68...
Toggling and resetting the outdoor recordings: 1. To toggle between the outdoor current, min/max temperature and humidity data and the times (for temperature data only) they were recorded press the min/out key: once to show the max outdoor temperature and humidity data with the recorded time and dat...
1. The distance of the weather projection station or sensor should be at least 6 feet (2 meters) away from any interfering sources such as computer monitors or tv sets. 2. Avoid placing the thermo-hygro sensor onto or in the immediate proximity of metal window frames. 3. Using other electrical produ...
• do not submerge the units in water. • immediately remove all low powered batteries to avoid leakage and damage. Replace only with new batteries of the recommended type. • do make any repair attempts to the units. Return it to their original point of purchase for repair by a qualified engineer. Ope...
• this product is only designed to be used in the home as indication of the future weather and is not 100% accurate. Weather forecasts given by this product should be taken only as an indication and not as being totally accurate. • the specifications of this product may change without prior notice. ...
Of repairs or alterations by someone other than an authorized la crosse technology, ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference.....