1. DL manuals
  2. La Crosse
  3. Weather Station
  4. WS-7013U
  5. Instruction Manual

La Crosse WS-7013U Instruction Manual

Manual is about: Wireless 433 MHz Temperature Station

Summary of WS-7013U

  • Page 1

    1 7, 0( ws-7013u wireless 433 mhz temperature station instruction manual.

  • Page 2: Table of Contents

    2 table of contents topic page inventory of contents 3 quick setup 4-8 detailed setup guide battery installation 9-10 setting the time 11-12 selecting units of measurement 12-13 features minimum and maximum temperatures 13 resetting minimum and maximum temperatures 14 additional remote temperature s...

  • Page 3: Inventory of Contents

    3 inventory of contents 1. The indoor temperature station (figure 1) 2. The remote temperature sensor (tx6u) and mounting bracket. (figure 2) 3. 3 each, 1/2” philips screws. 4. One strip of double sided adhesive tape. 5. Instruction manual and warranty card. Additional equipment (not included) 1. 1 ...

  • Page 4: Quick Setup

    4 quick setup hint: use good quality alkaline batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first t...

  • Page 5

    5 in this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 10 minutes please retry the se...

  • Page 6

    6 of resistance. Your distance plus resistance should not exceed 80 ft. In a straight line. Note: fog and mist will not harm your remote temperature sensor but direct rain must be avoided. To complete the set up of your indoor temperature station after the 10 minutes have passed please follow the st...

  • Page 7

    7 b. When you have your choice shown on the display press and release the “set” button once. 2. Degree fahrenheit will now show. A. To change between fahrenheit and celsius, press and release the “min/max” button. B. When you have your choice shown on the display press and release the “set” button o...

  • Page 8: Once More and You Are Done.

    8 pm hours. During the am hours this area will be blank. B. When the correct hour is shown, press and release the “set” button once. 4. A minute will now be flashing. A. Press and release the “min/max” button until the correct minutes are displayed. Press and release the set button once more and you...

  • Page 9: Detailed Setup Guide

    9 detailed setup guide i. Battery installation a. Remote temperature sensor 1. Remove the mounting bracket. 2. Remove battery cover 3. Observing the correct polarity, install 2 aa batteries—make sure they do not spring free, or start-up problems may occur. Replace cover..

  • Page 10: Indoor Temperature

    10 b. Indoor temperature station note: after the batteries are installed, do not press any buttons. This may interfere with the signals, causing temperatures to register incorrectly. 1. Remove the battery cover on the backside. To do this, push up and pull out. 2. Observing the correct polarity, ins...

  • Page 11: II.

    11 7, 0( 5. The indoor temperature station should now show: “-:- -” in the time lcd, and temperatures in the indoor and outdoor lcd’s. Ii. Time a. Setting the time 1. Press and hold the “set” button for 5 second, “12h” will appear in the time lcd. 2. Press and release the “min/max” button to select ...

  • Page 12: III.

    12 3. Press and release the “set” button 2 times, the hour will flash in the upper left corner. 4. Press and release the “min/max” button to set the hours 5. Press and release the “set” button to move to the minute setting 6. Press and release the “min/max” button to set the minutes. 7. Press and re...

  • Page 13: IV.

    13 1. Press and hold the “set” button for 5 second until “12h” or “24h” appears in the time lcd. 2. Press and release the “set” button again, “ °f” will appear in the time lcd. 3. Press and release the “min/max” button to shift between °f and °c. 4. Press and release the “set” button twice to activa...

  • Page 14: Resetting The Minimum and

    14 b. Resetting the minimum and maximum temperatures 1. To reset both the minimum and maximum temperatures—press and hold the “reset/+” button for 4 seconds. C. Adding additional remote temperature sensors (optional) 1. The ws-7013u is able to receive signals from 3 different remote temperature sens...

  • Page 15: Minutes.

    15 tx3up will monitor the temperature via a probe for use in pools, spas, etc. Note: when setting up multiple units it is important to remove the batteries from all existing units in operation, then to insert batteries first into all the remote temperature sensor units, and in numeric sequence. Seco...

  • Page 16: Viewing and Operating

    16 6. Install batteries into the indoor temperature station. 7. Follow the detailed set-up guide for programming and operating instructions. D. Viewing and operating with multiple remote temperature sensor units 1. To view the temperature of a different remote temperature sensor unit, press and rele...

  • Page 17: Mounting

    17 3. To reset the minimum/maximum readings, press and hold the “min/max” button for four seconds. V. Mounting note: to achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sensor on an outside north- facing wall. The sending range...

  • Page 18: The Temperature Station

    18 b. The temperature station 1. The indoor temperature station comes with the table stand already mounted. If you wish to use the table-stand, all that is required is to place the indoor temperature station in an appropriate location. 2. To wall mount, remove the table stand. To do this, pull down ...

  • Page 19: Problem: The Lcd Is Faint

    19 problem: the lcd is faint solution: replace batteries problem: no outdoor temperature is displayed. Solution: 1) remove all batteries, reinsert into remote temperature sensor first, and then into the indoor temperature station. 2) place remote temperature sensor closer to the indoor temperature s...

  • Page 20: Maintenance and Care

    20 the difference can be exaggerated further because the temperature sensors are designed for different working environments. The indoor sensor is less responsive to ambient air currents because of the shielding effect of the display's case. In addition, the case can act as a heat sink to absorb and...

  • Page 21: Specifications

    21 • clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may mark the displays and casings. • do not submerge in water. • do not subject the units to unnecessary heat or cold by placing them in the oven or freezer. • opening the casings invalidates the warr...

  • Page 22: Temperature Check

    22 indoor temperature station: outdoor -21.8 °f to 156.2°f with 0.2 °f resolution. (-29.9 °c to 69.0°c with 0.1 °c resolution) temp accuracy +/- 1 °f (+/- .5°c) transmitting range maximum 80 feet (25m) open space temperature check indoor every 10 seconds outdoor three times in 10 minutes batteries—(...

  • Page 23: Warranty Information

    23 remote temperature sensor 1.57“ x 0.9“ x 5.04“ (40 x 23 x 128 mm) battery life approximately 1 year warranty information la crosse technology, ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the ori...

  • Page 24

    24 technology, ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La crosse technology, ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty...

  • Page 25

    25 signal due to any source of interference.. This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations ...

  • Page 26: Fcc Disclaimer

    26 fax: 608.796.1020 e-mail: support@lacrossetechnology.Com (warranty work) sales@lacrossetechnology.Com (information on other products) web: www.Lacrossetechnology.Com fcc disclaimer this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this d...

  • Page 27: Fcc Id: Omo-01Rx (Receiver)

    27 fcc id: omo-01rx (receiver), omo-01tx (sensor) this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept interference received, including interference that may cause u...