1. DL manuals
  2. La Crosse
  3. Weather Station
  4. WS-7034U-IT
  5. Instruction Manual

La Crosse WS-7034U-IT Instruction Manual

Manual is about: Wireless 915 MHz Temperature Station

Summary of WS-7034U-IT

  • Page 1

    Ws-7034u-it wireless 915 mhz temperature station instruction manual.

  • Page 2: Table of Contents

    2 table of contents topic page quick setup 3-5 inventory of contents 6 detailed setup guide battery installation 7 setting the time 7-8 selecting units of measurement 9 features minimum and maximum temperatures 9-10 resetting minimum and maximum temperatures 10 adding additional remote temperature s...

  • Page 3: Quick Setup

    3 quick setup hint: use good quality alkaline batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first t...

  • Page 4

    4 display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displayed for 10 minutes you can place your re...

  • Page 5: Inventory of Contents

    5 note: fog and mist will not harm your remote temperature sensor but direct rain must be avoided. To complete the set up of your indoor temperature station after the 10 minutes have passed please follow the steps on pages 8-9. Inventory of contents 1. The indoor temperature station (figure 1) 2. Th...

  • Page 6: Additional Equipment

    6 additional equipment (not included) 1. 1 philips screwdriver. 2. 2 fresh aaa alkaline batteries. 3. 2 fresh aa alkaline batteries detailed setup guide battery installation 1. Install 2 aa batteries in the remote temperature sensor. Make sure they do not spring free, or start-up figure 1.

  • Page 7: Station. Do Not

    7 battery cover problems may occur. 2. Install 2 aaa batteries in the indoor temperature station. Do not press any buttons for at least ten minutes. Setting the time 1. Press and hold the “set” button for 5 second, “12h” will appear in the time lcd. 2. Press and release the “min/max” button to selec...

  • Page 8

    8 5. Press and release the “set” button to move to the minute setting 6. Press and release the “min/max” button to set the minutes. 7. Press and release the “set” button to activate the clock. Note: when in 12h mode, there is only a “pm” display, which appears under “time.” if there is no display he...

  • Page 9: Features

    9 features minimum and maximum temperatures 1. Press and release the “min/max” button, “min” appears next to the indoor and remote temperatures. 2. The recorded minimum temperature is displayed. 3. Press the “min/max” button, “max” appears next to the indoor and remote temperatures. 4. The recorded ...

  • Page 10: Adding Additional Remote

    10 resetting min and max temperatures to reset both the minimum and maximum temperatures—press and hold the “reset/+” button for 4 seconds. Adding additional remote temperature sensors (optional) the ws-7034u-it is able to receive signals from 3 different remote temperature sensors. Following are so...

  • Page 11: Mounting

    11 first into all the remote temperature sensors. Second install batteries into the indoor temperature station and do not press any buttons for ten minutes. Transmission problems will arise if this is not done correctly. To view the temperature of a different remote temperature sensor unit, press an...

  • Page 12: Remote Temperature Sensor

    12 remote temperature sensor 1. Remove the mounting bracket from the remote temperature sensor. 2. Mount the bracket in the desired location with either screws or adhesive tape. 3. Reattach the remote temperature sensor into mounting bracket. Indoor temperature station the indoor temperature station...

  • Page 13: Troubleshooting

    13 temperature station over the screw and pull down to secure. Troubleshooting note: for problems not solved, please contact la crosse technology via e-mail or phone, or visit our website, www.Lacrossetechnology.Com problem: the lcd is faint solution: replace batteries problem: no outdoor temperatur...

  • Page 14: Solution:

    14 so the straight-line signal is not passing through more than two or three walls. Problem: temperatures do not match if units are placed next to each other. Solution: each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions, so two sensors...

  • Page 15: Maintenance and Care

    15 is difficult to compensate for the above factors and obtain an accurate comparison. Maintenance and care instructions • extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • clean displays and units with a soft, damp cloth. Do not use solvents or scouring ...

  • Page 16: Measuring Temperatures

    16 measuring temperatures indoor temperature station 14.1 °f to 139.82°f with 0.2 °f resolution. (-9.9 °c to 59.9°c with 0.1 °c resolution). Remote temperature sensor -39.8 °f to 139.8°f with 0.2 °f resolution. (-39.8 °c to 59.9°c with 0.1 °c resolution). Temp accuracy +/- 1 °f (+/- .5°c). Transmitt...

  • Page 17

    17 dimensions: (l x w x h) indoor temperature station 2.36 x .88 x 5.90 in. (excluding table stand) (60 x 22.5 x 150 mm). Remote temperature sensor 2.32 x 0.86 x 2.55 in. (59 x 22 x 65 mm). Battery life up to 24 months. Warranty information la crosse technology, ltd provides a 1-year limited warrant...

  • Page 18

    18 of sale must be presented upon request as proof of purchase to la crosse technology, ltd or la crosse technology, ltd’s authorized service center. La crosse technology, ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or...

  • Page 19

    19 your la crosse technology, ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims mus...

  • Page 20

    20 similar damages associated with the operation or malfunction of this product. This product is not to be used for medical purposes or for public information. This product is not a toy. Keep out of children’s reach. This warranty gives you specific legal rights. You may also have other rights speci...

  • Page 21

    21 sales@lacrossetechnology.Com (information on other products) web: www.Lacrossetechnology.Com fcc disclaimer this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any...

  • Page 22: 1. This Device May Not Cause

    22 duplicated or processed using electronic, mechanical or chemical procedures without written permission of the publisher. This handbook may contain mistakes and printing errors. The information in this handbook is regularly checked and corrections made in the next issue. We accept no liability for...