1. DL manuals
  2. La Crosse
  3. Weather Station
  4. WS-9002U
  5. Instruction Manual

La Crosse WS-9002U Instruction Manual

Manual is about: Wireless 433 MHz Temperature Station

Summary of WS-9002U

  • Page 1

    1 ws-9002u wireless 433 mhz temperature station instruction manual.

  • Page 2: Table of Contents

    2 table of contents topic page inventory of contents 3 quick setup 4-6 detailed setup guide battery installation 7-8 features minimum and maximum temperatures 9 resetting minimum and maximum temperatures 9 additional remote temperature sensors (optional) 10-12 mounting 12-14 troubleshooting 14-16 ma...

  • Page 3: Inventory of Contents

    3 inventory of contents 1. The indoor temperature station (figure 1) 2. The remote temperature sensor (tx6u) and mounting bracket. (figure 2) 3. 3 each, 1/2” philips screws. 4. One strip of double sided adhesive tape. 5. Instruction manual and warranty card. Additional equipment (not included) 1. 1 ...

  • Page 4: Quick Setup

    4 quick setup hint: use good quality alkaline batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first t...

  • Page 5

    5 in this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 15 minutes please retry the se...

  • Page 6

    6 of resistance. Your distance plus resistance should not exceed 80 ft. In a straight line. Note: fog and mist will not harm your remote temperature sensor but direct rain must be avoided..

  • Page 7: Detailed Setup Guide

    7 detailed setup guide i. Battery installation a. Remote temperature sensor 1. Remove the mounting bracket. 2. Remove battery cover 3. Observing the correct polarity, install 2 aa batteries—make sure they do not spring free, or start-up problems may occur. Replace cover..

  • Page 8: Indoor Temperature

    8 b. Indoor temperature station note: after the batteries are installed, do not press any buttons. This may interfere with the signals, causing temperatures to register incorrectly. 1. Remove the battery cover on the backside. 2. Observing the correct polarity, install 2 aaa batteries. 3. Replace ba...

  • Page 9: II.

    9 ii. Features a. Minimum and maximum temperatures 1. Press and release the “min/max” button, “min” appears in the temperature lcd’s and the recorded minimum temperatures are displayed. 2. Press and release the “min/max” button to toggle to the maximum temperatures. B. Resetting the minimum and maxi...

  • Page 10: C. Adding Additional

    10 c. Adding additional remote temperature sensors (optional) 1. The ws-9002u is able to receive signals from 3 different remote temperature sensors. Following are some brief instructions for the basic set-up of remote temperature sensor units with the ws-9002u. These extra sensors can be purchased ...

  • Page 11: Minutes.

    11 batteries into the indoor temperature station. Transmission problems will arise if this is not done correctly and if the total time for set-up exceeds 6 minutes. 2. It is necessary to remove the batteries from all units currently in operation. 3. Remove the battery covers to all remote temperatur...

  • Page 12: III.

    12 from one “boxed” number to the next should be observed in the outdoor lcd. 2. To view the minimum/maximum temperature: first select from which remote temperature sensor to read data (indicated by the “boxed” number). Pressing and releasing the “min/max” button will toggle through the minimum and ...

  • Page 13: Remote Temperature

    13 both units in their desired location before permanently mounting. A. Remote temperature sensor 1. Remove the mounting bracket from the remote temperature sensor 2. Mount using either screws or adhesive tape. 3. Reattach the remote temperature sensor to the mounting bracket. B. The temperature sta...

  • Page 14: Troubleshooting

    14 temperature station onto the screw using the hanging hole on the backside. Gently pull the indoor temperature station down to lock the screw into place. Troubleshooting note: for problems not solved, please contact la crosse technology via e-mail or phone, or visit our website, www.Lacrossetechno...

  • Page 15

    15 4) place remote temperature sensor and indoor temperature station in position so the straight-line signal is not passing through more than two or three walls. Problem: temperatures do not match if units are placed next to each other. Solution: each temperature sensor is manufactured to be accurat...

  • Page 16: Maintenance and Care

    16 ends of a range, making it harder to compare different ranges with different curves. Under non-laboratory conditions, it is difficult to compensate for the above factors and obtain an accurate comparison. Maintenance and care instructions • extreme temperatures, vibration, and shock should be avo...

  • Page 17: Specifications

    17 specifications transmitting frequency 433mhz measuring temperatures indoor temperature station: indoor 32 °f to 140°f with 0.2 °f resolution. Indoor temperature station: outdoor -21.8 °f to 157.8°f with 0.2 °f resolution. Transmitting range maximum 80 feet (25m) open space temperature checking in...

  • Page 18: Dimensions:  (H X W X D)

    18 dimensions: (h x w x d) indoor temperature station 3.75 x 2.5 x 1 in (98 x 63 x 25 mm) remote temperature sensor 5 x 1.5 x 1 in (128 x 40 x 23 mm) battery life approximately 1 year.

  • Page 19: Warranty Information

    19 warranty information la crosse technology, ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in north america and only to th...

  • Page 20

    20 technology, ltd and must be returned to la crosse technology, ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La crosse technology, ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If ...

  • Page 21

    21 damage resulting from failure to follow instructions contained in your owner’s manual; (5) damage resulting from the performance of repairs or alterations by someone other than an authorized la crosse technology, ltd authorized service center; (6) units used for other than home use (7) applicatio...

  • Page 22

    22 product is not a toy. Keep out of children’s reach. This warranty gives you specific legal rights. You may also have other rights specific to your state. Some states do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. ...

  • Page 23: Fcc Disclaimer

    23 fcc disclaimer this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Freq. ...