1. DL manuals
  2. La Crosse
  3. Weather Station
  4. WS-9016U
  5. Instruction manual

La Crosse WS-9016U Instruction manual

Manual is about: Wireless 433 MHz Radio-controlled Sun/Moon Weather Station

Summary of WS-9016U

  • Page 1

    Ws-9016u wireless 433 mhz radio-controlled sun/moon weather station instruction manual.

  • Page 2: Topic Page

    2 topic page inventory of contents/additional equipment 3 about wwvb 4 quick set-up guide 5 detailed set-up guide battery installation 6 program mode function keys 7-8 lcd screen 9 manual settings sequence 9 lcd contrast setting 10 city location setting 10 time zone setting 11 daylight saving time (...

  • Page 3: Inventory of Contents

    3 inventory of contents 1. The indoor weather station (figure 1). 2. One tx6u remote temperature sensor with mounting bracket (figure 2). 3. Three each, ½” philips screws. 4. One strip double-sided adhesive tape. 5. Instruction manual and warranty card. Additional equipment (not included) 1. Two, fr...

  • Page 4: Quick Set-Up Guide

    4 about wwvb (radio controlled time) the nist (national institute of standards and technology—time and frequency division) wwvb radio station is located in ft. Collins, colorado and transmits the exact time signal continuously throughout the united states at 60 khz. The signal can be received up to ...

  • Page 5: Detailed Set-Up Guide

    5 note: fog and mist will not harm your remote temperature sensor but direct rain must be avoided. To complete the set up of your indoor weather station after the 10 minutes have passed please follow the steps starting on page 6. Note: the remote temperature sensor transmits a signal every 3 minutes...

  • Page 6: II.  Program Mode

    6 2. Observe the correct polarity, and install 2 aa batteries. 3. Replace the battery cover. Note: immediately after the batteries have been installed, each lcd (liquid crystal display) will flash and a tone will sound. Within a few seconds the indoor temperature, indoor relative humidity and the we...

  • Page 7: 2.  Plus (+) Button

    7 manual time setting, calendar, snooze function, temperature °c or °f, and weather icon sensitivity setting • stop the alarm during alarm ringing 2. Plus (+) button • increase value in all setting modes • increase the digits • stop the alarm during alarm ringing 3. Minus (-) button • decrease value...

  • Page 8: B.  Lcd Screen

    8 8. Max/min r button (max/min reset) • press shortly to toggle between maximum, minimum and current temperature value for selected outdoor temperature channel. • press and hold for 4 seconds to reset the maximum and minimum records for selected temperature channel. • press to activate snooze functi...

  • Page 9: Lcd Contrast Setting

    9 • time zone setting • dst (daylight saving time) setting • wwvb on/off setting • 12/24-hour setting • manual time setting • calendar setting • snooze setting • °c/°f setting • weather forecasting icon sensitivity setting lcd contrast setting the lcd contrast can be set within 8 levels, from lcd 0 ...

  • Page 10: Setting.

    10 flashing 4. When a city is selected the city’s time zone will be displayed on the 4-time zone map located on the right side of the lcd. 5. Press and release the “set” button to confirm and enter in the time zone setting. For a list of cities please see page 25 please. Time zone setting the defaul...

  • Page 11: Setting.

    11 digits flashing tower icon flashing flashing 3. Press and release the “set” button to confirm and enter the wwvb on/off setting. Wwvb on/off setting in areas where reception of the wwvb time is not possible the wwvb time reception function can be turned off. The clock will then work as a normal q...

  • Page 12: Manual Time Setting

    12 manual time setting in case the indoor weather station cannot detect the wwvb signal (for example due to disturbances, transmitting distance, etc.), the time can be manually set. The clock will then work as a normal quartz clock. 1. The hour digit will start flashing on the lcd. 2. Press and rele...

  • Page 13: Snooze Setting

    13 the default (factory set) date of the indoor weather station is 1. 1. In the year 2001. Once the radio-controlled time signal is received the date is automatically updated. If the signals are not received the date can also be set manually. 1. The year starts flashing in the lcd. 2. Press and rele...

  • Page 14: Setting

    14 digit flashing 3. Press and release the “set” button to confirm and enter the temperature setting note: if the snooze time has been set “off” the snooze function will not be activated. °f/°c temperature setting the temperature display can be selected to show temperature data in °c or °f (the defa...

  • Page 15: Manual Settings.

    15 3. There are 3 levels of setting: 1, 2 and 3; level 1 is the most sensitive setting, level 3 is the slowest recording setting (the default setting is "2"). 4. Press and release the “set” button to confirm and exit the manual settings. To exit the manual setting mode to exit the manual setting mod...

  • Page 16: Moon Phase Symbols

    16 to stop the alarm, press any button during alarm ringing. Sun/moon data and moon phases sun/moon data for selected city 1. The sunrise/sunset and moonrise/moonset time for each of the preset cities can be displayed by pressing the “sun/moon” button. 2. Press and release the plus (+) or minus (-) ...

  • Page 17: Weather Forecasting Icons:

    17 note: it may happen that there is no moonrise or moonset on a certain date, consequently “+1” above the moonrise or moonset time will be displayed to indicate that it will occur at the displayed time the next day. Indoor relative humidity and indoor temperature the indoor temperature and humidity...

  • Page 18: Weather Tendency Indicator

    18 for every sudden or significant change in the air pressure the weather icons will update accordingly to represent the change in weather. If the icons do not change, then it means either the air pressure has not changed or the change has been too slow for the indoor weather station to register. Ho...

  • Page 19: Outdoor Temperature:

    19 taking this into account one can see how the weather has changed, and is expected to change. For example, if the indicator is pointing downwards together with cloud and sun icons, then the last noticeable change in the weather was when it was sunny (the sun icon only). Therefore, the next change ...

  • Page 20: Set-Up of Multiple Units

    20 3. To reset the maximum and minimum outdoor temperature, and the time at which they were recorded, press and hold the “max/min r” button for 4 seconds. This will reset all minimum and maximum data recorded to the displayed values for the selected remote temperature sensor. Adding outdoor remote t...

  • Page 21: Mounting

    21 mounting note: before permanently mounting ensure that the indoor weather station is able to receive wwvb signals from the desired location. Also, extreme and sudden changes in temperature will decrease the accuracy of the indoor weather station and changes in elevation will result with inaccurat...

  • Page 22: A.  Using The Table Stand

    22 secure hold. The mounting surface should be smooth and flat. 2. Remove the protective strip from one side of the tape. 3. Adhere the tape to the designated area on the back of the mounting bracket. 4. Remove the protective strip from the other side of the tape. 5. Position the remote temperature ...

  • Page 23: City Listing

    23 city listing (in order as they appear on left side of unit) montgomery, alabama little rock, arkansas phoenix, arizona los angeles, california san francisco, california denver, colorado washington d.C. Jacksonville, florida miami, florida atlanta, georgia des moines, iowa boise, idaho chicago, il...

  • Page 24: Problem:

    24 are selected. Problem: the lcd is faint solution: 1) set the lcd contrast to a higher number 2) replace batteries problem: no remote temperature is displayed solution: 1) remove all batteries, reinsert into remote sensor(s) first, then indoor weather station. 2) place remote sensor(s) closer to i...

  • Page 25: Specifications

    25 specifications temperature measuring range: indoor: 32 °f to 140°f with 0.1°f resolution. (0 °c to 60°c with 0.1 °c resolution) “of” displayed if outside this range outdoor: -21.8 °f to 157.8°f with 0.2°f resolution. (-29.9 °c to 69.9°c with 0.1 °c resolution) “of” displayed if outside this range...

  • Page 26: Warranty Information

    26 warranty information la crosse technology provides a 1-year warranty on this indoor weather station. Contact la crosse technology immediately upon discovery of any defects covered by this warranty. Before sending the indoor weather station in for repairs, contact la crosse technology. The indoor ...

  • Page 27

    27 fcc id: omo-01rx (receiver), omo-01tx (transmitter) this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept interference received, including interference that may ca...