Ws-9055twc wireless 433 mhz weather station instruction manual.
2 table of contents topic page quick setup 3-5 inventory of contents 6-7 detailed setup guide battery installation 7 setting the time 8 features minimum and maximum temperatures 9 resetting minimum and maximum temperatures 10 adding additional remote temperature sensors (optional) 10-11 weather fore...
3 quick setup hint: use good quality alkaline batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first t...
4 will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 15 minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displ...
5 your distance plus resistance should not exceed 80 ft. In a straight line. Note: fog and mist will not harm your remote temperature sensor but direct rain must be avoided. To complete the set up of your indoor temperature station after the 15 minutes have passed please follow the steps in the deta...
6 additional equipment (not included) 1. 1 philips screwdriver. 2. 2 fresh aa alkaline batteries. 3. 2 fresh aa alkaline batteries detailed setup guide battery installation figure 2 holder figure 1.
7 1. Install 2 aa batteries in the remote temperature sensor. Make sure they do not spring free, or start-up problems may occur. 2. Install 2 aa batteries in the indoor weather station. Do not press any buttons for at least fifteen minutes. Setting the time 1. Press and hold the “set” key for 4 seco...
8 7. Press and release the “set” key to exit programming. Features minimum and maximum temperatures 1. Press and release the “min/max” button, “max” appears between the indoor and remote temperatures. 2. The recorded maximum indoor and remote temperature is displayed. 3. Press and release the “min/m...
9 while viewing the minimum or maximum temperatures. Resetting min and max temperatures to reset both the minimum and maximum temperatures—press and hold the “min/max” button for 5 seconds. Adding additional remote temperature sensors (optional) the ws-9055u is able to receive signals from 3 differe...
10 will monitor temperature and display the temperature on its lcd, and the tx3up will monitor the temperature of water or soil via a probe. When setting up multiple remote temperature sensors, it is important to remove the batteries from all existing units in operation, then to insert batteries fir...
11 weather forecast the weather forecasting feature is estimated to be 75% accurate. The weather forecast is based solely upon the change of air pressure over time. The ws- 9055u averages past air-pressure readings to provide an accurate forecast, creating a necessity to disregard all weather foreca...
12 sunny—indicates that the weather is expected to improve (not that the weather will be sunny). Sun with clouds— indicates that the weather is expected to be fair (not that the weather will be sunny with clouds). Clouds with rain— indicates that the weather is expected to get worse (not that the we...
13 “rainy”, although it is possible for the change to occur quickly. If the symbols do not change then the weather has not changed, or the change has been slow and gradual. Weather tendency arrows other possible displays in the forecast lcd are 2 weather tendency arrows, one that points up (on the l...
14 mounting note: to achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sensor on a north- facing wall. The sending range is 80ft; obstacles such as walls, concrete, and large metal objects will reduce the range. Place both units...
15 required is to place the indoor weather station in an appropriate location. To wall mount the indoor weather station first remove the table stand. Next insert an appropriate screw in your desired location. Using the integrated hanging hole on the back of the unit, slip indoor weather station over...
16 solution: 1. Remove all batteries, reinsert into remote temperature sensor first, then into the indoor weather station. 2. Place remote temperature sensor closer to the indoor weather station. 3. Be sure all batteries are fresh. 4. Place remote temperature sensor and indoor weather station in pos...
17 of the shielding effect of the display's case. In addition, the case can act as a heat sink to absorb and store heat from external sources (i.E. Handling of the case or radiant heat). Also, the much greater range of the outdoor temperature sensor requires a different calibration curve than the in...
18 scouring agents; they may mark the displays and casings. • do not submerge in water. • do not subject the units to unnecessary heat or cold by placing them in the oven or freezer. • opening the casings invalidates the warranty. Do not try to repair the unit. Contact la crosse technology repairs. ...
19 temp accuracy +/- 1 °f (+/- .5°c) transmitting range maximum 80 feet (25m) open space temperature check indoor every 10 seconds outdoor twice in 10 minutes batteries—(alkaline recommended) remote temperature sensor 2 x aa, 1.5v indoor weather station 2 x aa, 1.5v dimensions: (l x w x h) indoor we...
20 warranty information la crosse technology, ltd provides a 1- year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in north america and only to t...
21 be defective during the limited warranty period specified above. All replaced parts and products become the property of la crosse technology, ltd and must be returned to la crosse technology, ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whicheve...
22 unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4) damage resulting from failure to follow instructio...
23 la crosse technology, ltd will not assume liability for incidental, consequential, punitive, or other similar damages associated with the operation or malfunction of this product. This product is not to be used for medical purposes or for public information. This product is not a toy. Keep out of...
24 for warranty work, technical support, or information contact: la crosse technology 2809 losey blvd. S. La crosse, wi 54601 phone: 608.782.1610 fax: 608.796.1020 e-mail: support@lacrossetechnology.Com (warranty work) sales@lacrossetechnology.Com (information on other products) web: www.Lacrossetec...
25 fcc disclaimer this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation. All rights...