La Crosse WS-9060U-IT Quick Setup Manual
1
LCD
Display
Function key
Stand
Function keys
WS-9060U-IT FORECAST STATION
Quick Setup Guide
INTRODUCTION:
Congratulations on purchasing this state-of-the-art
weather station as an example of innovative design and
quality piece of engineering. Providing time, calendar,
weather forecast, moon phase, indoor and outdoor
temperature, indoor and outdoor relative humidity. This
unit will never keep you guessing on current and future
weather conditions.
The Weather Station
FEATURES:
x
12/24 hour time display
x
Calendar display (year shows only in set mode)
x
Display 8 Moon phases throughout the year
x
Weather forecasting with weather tendency indicator
x
Indoor and outdoor temperature display with
MIN/MAX records
x
Temperature display in ºC/ ºF
x
Indoor and outdoor humidity display
x
Humidity data display as RH%
x
Low battery indicator
Battery
compartment
Hanging
hole
2
INITIAL SETUP:
Do not mix old and new batteries. Do not mix alkaline,
standard, or rechargeable batteries
1.
Install batteries (2-AAA LR3, 1.5V) into the Thermo-
hygro Transmitter according to polarity.
2.
Install batteries (2-AAA LR3, 1.5V) into the Weather
Station according to polarity.
3.
Place the transmitter and weather station 5-10 feet
apart. When the batteries are inserted, the weather
station will start receiving data signal from the
transmitter. The outdoor temperature and humidity
data should be displayed on the weather station.
4.
If this does not happen after 2 minutes, the batteries
will need to be removed from both units and reset
from step 1.
5.
If the outdoor temperature and humidity are
displayed for 15 minutes, the transmitter can be
placed outside.
Note:
When changing batteries in the units, ensure the batteries
do not spring free from the contacts. Always wait at least
15 minutes after removing the batteries before reinserting,
otherwise start up and transmission problems may occur.
TO INSTALL AND REPLACE BATTERIES IN THE
THERMO-HYGRO TRANSMITTER
The outdoor thermo-hygro transmitter uses 2 x AAA, IEC
LR3, 1.5V batteries. To install and replace the batteries,
please follow the steps below:
1.
Remove the battery cover.
2.
Insert the batteries, observing the
correct polarity (see battery
compartment marking).
3.
Replace the battery cover on the unit.
Note:
When changing batteries in any of the units,
all units need to be reset by following the
setting up procedures. This is due to a random security
code assigned by the transmitter at start-up. This code
must be received and stored by the weather station in the
first 3 minutes of power being supplied to the transmitter.
3
+ key
MIN/MAX key
SET key
TO INSTALL AND REPLACE BATTERIES IN THE
WEATHER STATION
The weather station uses 2 x AAA, IEC LR3, 1.5V
batteries. To install and replace the batteries, please follow
the steps below:
1.
Insert finger or other solid
object in the space at the
bottom center of the
battery compartment and
lift up to remove the
cover.
2.
Insert batteries observing
the correct polarity (see
marking).
3. Replace
compartment
cover.
BATTERY CHANGE:
It is recommended to replace the batteries in all units on
an annual basis to ensure optimum accuracy of these
units.
Please participate in the preservation of
the environment. Return used batteries to
an authorized depot.
FUNCTION KEYS:
Weather Station:
The Weather Station has 3 easy to use function keys: 1
key on the front, and 2 keys on the back
4
MANUAL SETTINGS: The SET key will move you through
the program menu. The + key will change a value.
12/24-HOUR TIME: Hold the SET key and 12h or 24h will
flash. Use the + key to select 12-hour or 24-hour time.
Press and release the SET key to confirm and continue.
HOUR: The Hour will flash. Use the + key to select the
Hour. Press and release the SET key to confirm and
continue.
MINUTES: The Minutes will flash. Use the + key to select
the Minutes. Press and release the SET key to confirm
and continue.
YEAR: The Year will flash. Use the + key to select the
Year (the year will not display on the weather station).
Press and release the SET key to confirm and continue.
MONTH: The Month will flash. Use the + key to select the
Month. Press and release the SET key to confirm and
continue.
DATE: The Date will flash. Use the + key to select the
Date. Press and release the SET key to confirm and
continue.
°F/°C TEMPERATURE: °F/°C will flash. Use the + key to
select the °F or °C . Press and release the SET key to
confirm and exit the manual settings.
MOON PHASES SYMBOL
The moon icon of the weather station will also display all 8
moon phases throughout the year according to the set
calendar. A bar segment above the moon phase will
indicate current moon phase.
WEATHER FORECASTING ICONS:
The weather icons in the second section of LCD can be
displayed in any of the following combinations:
New
Moon
Waning
Crescent
First
Quarter
Waxing
Gibbous
Waxing
Crescent
Last
Quarter
Full
Moon
Waning
Gibbous
Bar segment (moon phase indicator)