1. DL manuals
  2. La Crosse
  3. Weather Station
  4. WS-9117U-IT
  5. Instruction Manual

La Crosse WS-9117U-IT Instruction Manual

Manual is about: Wireless 915 MHz Temperature Station

Summary of WS-9117U-IT

  • Page 1

    1 ws-9117u-it wireless 915 mhz temperature station instruction manual.

  • Page 2: Topic

    2 table of contents topic page inventory of contents quick setup detailed setup guide battery installation setting the time features minimum and maximum temperatures resetting minimum and maximum temperatures additional remote temperature sensors (optional) mounting troubleshooting maintenance and c...

  • Page 3: Variations In Real-Time!

    3 inventory of contents 1. The indoor temperature station (figure 1) 2. The remote temperature sensor (tx29u- it) and mounting bracket. (figure 2) 3. 3 each, 1/2” philips screws. 4. One strip of double sided adhesive tape. 5. Instruction manual and warranty card. Instant transmission is the state-of...

  • Page 4: Additional Equipment

    4 additional equipment (not included) 1. 1 philips screwdriver. 2. 2 fresh aaa 1.5v batteries. 3. 2 fresh aa 1.5v batteries quick setup hint: use good quality alkaline batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. ...

  • Page 5

    5 3. Place the batteries into the remote temperature sensor first then into the indoor temperature station. (all remote temperature sensors must be started before the indoor temperature station) 4. Do not press any buttons for 15 minutes. In this time the indoor temperature station and remote temper...

  • Page 6

    6 walls, floors, ceilings, thick trees, etc.) will effectively cut signal range in half. Example: a wireless weather station with a 330 feet range is mounted on an interior wall, so that the signal has to pass through one interior wall, one exterior wall, and across the 10 feet width of the room bet...

  • Page 7

    7 to complete the set up of your indoor temperature station after the 15 minutes have passed please follow the steps below. 1. Press and hold the “set/ch” button for 5 seconds. Note: a “12h” or “24h” will appear on the top line. (“12h” for am/pm, “24h” for military time) 2. To change between “12h” a...

  • Page 8: More And You Are Done.

    8 6. When the correct hour is shown, press and release the “set/ch” button once. Press and release the set button once more and you are done. Detailed setup guide battery installation - when one temperature sensor is being used 1. First, insert the batteries to the temperature sensor (see “a. Temper...

  • Page 9: A. Remote

    9 temperature and humidity should then be displayed on the temperature station. If this does not happen after 2 minutes, the batteries will need to be removed from both units and reset from step 1 and the signal reception icon is no longer shown. A. Remote temperature sensor a. Remove the mounting b...

  • Page 10

    10 a. Remove the battery cover on the backside. To do this, push up and pull out. B. Observing the correct polarity, install 2 aaa batteries. C. Replace battery cover. D. Wait 15 minutes to allow both the indoor and outdoor temperatures are shown on the indoor temperature station. Battery cover.

  • Page 11: Reception Icon *

    11 * when the signal is successfully received by the temperature station, the icon will be switched on. (if not successful, the icon will not be shown in lcd) so the user can easily see whether the last reception was successful (icon on) or not (icon off). On the other hand, the short blinking of th...

  • Page 12: Setting The Time

    12 910mhz. This will also be done for re- synchronization. Setting the time 1. Press and hold the “set/ch” button for 5 second, “12h” will appear in the time lcd. 2. Press and release the “min/max” button to select either 12h time (am/pm) or 24h time 3. Press and release the “set/ch” button 2 times,...

  • Page 13: Temperatures

    13 there is no display here it is am. Make sure you set the time accordingly. Note: if “12h” is selected, the temperature is displayed in degree fahrenheit. If “24h” is selected, the temperature is displayed in degree celsius features minimum & maximum temperatures 1. Press and release the “min/max”...

  • Page 14: Adding Additional Remote

    14 adding additional remote sensors (optional) the ws-9117u-it is able to receive signals from 2 additional temperature sensors. The following are instructions for the set-up of temperature sensor units with the ws-9117u- it. These extra sensors can be purchased through the same dealer as this unit....

  • Page 15: Sensor.

    15 this does not happen and the signal reception icon is not shown, after 2 minutes, the batteries will need to be removed from both units and reset from step 1. 5. Insert the batteries to the second sensor as soon as the outdoor temperature readings from the first sensor are displayed on the temper...

  • Page 16: Multiple Remote Temperature

    16 received. If this is not happen, user shall restart the setting up from step 1. Note: you must insert the batteries into the third sensor within 45 seconds of reception of the second sensor. Important: transmission problems will arise if the setting for multiple sensors is not followed as describ...

  • Page 17: 1. Remote Temperature Sensor

    17 button will toggle through the minimum and maximum indoor temperature, and the minimum and maximum outdoor temperature. 3. To reset the minimum/maximum readings, press and hold the “min/max” button for four seconds. Mounting note: to achieve a true temperature reading, avoid mounting in direct su...

  • Page 18: To Wall Mount:

    18 to wall mount: a. Remove the mounting bracket from the temperature sensor. B. Mount using either screws or adhesive tape. C. Reattach the temperature sensor to the mounting bracket. 2. The temperature station a. The indoor temperature station comes with the table stand already mounted. If you wis...

  • Page 19: Problem: The Lcd Is Faint

    19 troubleshooting note: for problems not solved, please contact la crosse technology via e-mail or phone, or visit our website, www.Lacrossetechnology.Com problem: the lcd is faint solution: replace batteries problem: no outdoor temperature i displayed. Solution: 1) remove all batteries, reinsert i...

  • Page 20

    20 conditions; so two temperature sensors could be as much as 2 degrees different. However, the difference can be exaggerated further because the temperature sensors are designed for different working environments. The indoor sensor is less responsive to ambient air currents because of the shielding...

  • Page 21: Measuring Temperatures

    21 scouring agents; they may mark the displays and casings. 9 do not submerge in water. 9 do not subject the units to unnecessary heat or cold by placing them in the oven or freezer. 9 opening the casings invalidates the warranty. Do not try to repair the unit. Contact la crosse technology for repai...

  • Page 22: Dimensions:  (H X W X D)

    22 outdoor every 4 seconds batteries—(alkaline recommended) remote temperature sensor 2 x aa, 1.5v indoor temperature station 2 x aaa, 1.5v dimensions: (h x w x d) indoor temperature station 5 x 2.25 x 1 in. (excluding table stand) ( 125 x 58 x 23 mm) remote temperature sensor 5.05 x 1.50 x 0.83 in....

  • Page 23

    23 to receive warranty service, the purchaser must contact la crosse technology, ltd for problem determination and service procedures. Warranty service can only be performed by a la crosse technology, ltd authorized service center. The original dated bill of sale must be presented upon request as pr...

  • Page 24

    24 examination. The owner must pay any shipping charges incurred in getting your la crosse technology, ltd product to a la crosse technology, ltd authorized service center. La crosse technology, ltd will pay ground return shipping charges to the owner of the product to a usa address only. Your la cr...

  • Page 25

    25 interference.. This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set- up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation...

  • Page 26

    26 la crosse technology 2809 losey blvd. S. La crosse, wi 54601 phone: 608.782.1610 fax: 608.796.1020 e-mail: support@lacrossetechnology.Com (warranty work) sales@lacrossetechnology.Com (information on other products) web: www.Lacrossetechnology.Com questions? Instructions? Please visit: www.Lacross...

  • Page 27: Rf Exposure Mobile:

    27 corrections made in the next issue. We accept no liability for technical mistakes or printing errors, or their consequences. All trademarks and patents are acknowledged. Fcc id: omotx29u (transmitter) rf exposure mobile: the internal / external antennas used for this mobile transmitter must provi...

  • Page 28

    28 note: this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and ca...