1 contents language page _______________________________________________ english 1 french 47 spanish wireless 915 mhz temperature station instruction manual introduction: congratulations on purchasing this compact 915mhz wireless temperature station which displays time, indoor temperature, outdoor t...
2 features: the temperature station • quartz clock in 12 or 24-hour time display (hour and minute, manually set) • indoor and outdoor temperature reading in fahrenheit (°f) or celsius (°c) • indoor humidity reading in %rh • wireless transmission at 915 mhz • signal reception intervals at 16-second •...
3 • wall mounting case (mount in a sheltered location. Avoid direct rain and sunlight) setting up: when one sensor is used 1. First, insert the battery into the temperature sensor. (see “install and replace batteries in the temperature sensor“). 2. Immediately after and within 30 seconds, insert the...
4 place, all segments of the lcd will light up briefly. Following time as 12:00 and the indoor temperature will be displayed. If they are not shown in lcd after 60 seconds, remove the batteries and wait for at least 60 seconds before reinserting them. 4. The outdoor temperature from the first sensor...
5 if the signal reception is not successful on the first frequency (915mhz) for 45 seconds, the frequency is changed to 920mhz and the learning is tried for another 45 seconds. If still not successful the reception is tried for 45 seconds on 910mhz. This will also be done for re-synchronization. Imp...
6 2. Insert the batteries, observing the correct polarity (see marking). 3. Replace the battery cover on the unit. Note: in the event of changing batteries in any of the units, all units need to be reset by following the setup procedures. This is because a random security code is assigned by the sen...
7 set/ch key (setting/channel) • press and hold for approximately 3 seconds to enter the manual setting mode. • press and release to toggle between different channel readings. Min/max/+ key (min/ max temperature) • used to toggle between the minimum and maximum recorded readings of indoor & outdoor ...
8 (“off” icon). On the other hand, the short blinking of the icon shows that a reception is being done at that time. For a better display clarity, the lcd screen is split into 3 sections, showing the information of time, indoor temperature and humidity, and outdoor data. Section 1 - time • display o...
9 manual time setting user shall manually set the time of the temperature station by the following steps: 1. The hour digit of the time display will be flashing. 2. Press the “min/max/+” key to adjust the hour (press and hold to allow fast advance). Press “set/ ch” key to confirm and go to the minut...
10 resetting the minimum and maximum readings: user may reset the minimum and maximum temperature / humidity data to the current value by the following steps: 1. Press the “min/max/+” key once to display the minimum data. 2. Press and hold the “min/max/+” key for about 3 seconds to reset all the min...
11 received about 2 minutes after setup (the signal reception icon does not appear), please check the following points: 1. The distance of the temperature station or sensor should be at least 1.5 to 2 meters away from any interfering sources such as computer monitors or tv sets. 2. Avoid positioning...
12 positioning positioning the temperature station: the temperature station comes attached with a table stand, which provides the option of table standing the unit in addition to wall mounting. Before wall mounting, please check that the outdoor temperature values can be received from the desired lo...
13 using the bracket which doubles as a stand or wall mount base. To wall mount: 1. Secure the bracket onto a desired wall using the screws and plastic anchors. 2. Clip the temperature sensor onto the bracket. Note: the mounting surface can affect the transmission range. If, for instance, the unit i...
14 • do not submerge the units in water. Place units in locations that are adequately protected against moisture and rain. • immediately remove all low powered batteries to avoid leakage and damage. Replace only with new batteries of the recommended type (alkaline). • do not make any repair attempts...
15 approximately 12 months dimensions (l x w x h) temperature station : 2.29" x 0.69" x 4.66" (58.2 x 17.6 x 118.4 mm) temperature sensor : 1.44" x 0.53" x 3.46" (36.6 x 13.5 x 87.9 mm ) warranty la crosse technology, ltd provides a 1-year limited warranty on this product against manufacturing defec...
16 crosse technology, ltd will pay ground return shipping charges to the owner of the product to a usa address only. Your la crosse technology, ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, unreasonable use or negl...
17 for warranty work, technical support, or information contact: la crosse technology, ltd 2809 losey blvd. S. La crosse, wi 54601 phone: 608.782.1610 fax: 608.796.1020 e-mail: support@lacrossetechnology.Com (warranty work) sales@lacrossetechnology.Com (information on other products) web: www.Lacros...
