- DL manuals
- Lab.gruppen
- Amplifier
- fP Series FP 2600
- User Manual
Lab.gruppen fP Series FP 2600 User Manual
Summary of fP Series FP 2600
Page 1
Ñm=osmm= rpbo=j^kr^i= =.
Page 2: N= `lkqbkqp=
N= `lkqbkqp= 1 contents .......................................................................................................................................1 2 approvals...................................................................................................................................
Page 3: O= =^mmols^ip=
9.1.5 ac mains voltage protection ............................................................................................15 9.1.6 dc protection ...................................................................................................................16 10 maintenance......................
Page 4
8. Always operate the unit with the chassis ground wire connected to the electrical safety earth. Do not defeat the safety purpose of a grounding-type plug. A grounding type plug has two pins and a third grounding prong. The third prong is provided for your safety. If the provided plug does not fit ...
Page 5: Q= Fkqolar`qflk=
• increase the separation between the equipment and receiver. • connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • check if the affected unit complies with the emc limits for immunity, (ce-labelled). If not, address the problem with the manufa...
Page 6
This indicator illuminates if signals above 12 khz are continuously present at full power at the output terminals or if short circuit protection is activated. If this occurs the input signal is muted, and the process cycles until the vhf signal is no longer present or the short is removed. (see page...
Page 7: R= Ob^o=M^kbi=Cb^qrobp=
Three of the switches in the dip switch selects the maximum gain of the channel to be either 20, 23, 26, 29, 32, 35, 38 or 41db. (see page 6 ) 9. Ac power cable r= ob^o=m^kbi=cb^qrobp= before turning the amplifier on please read the following sections to make sure that the unit is set up properly fo...
Page 8
Rknkp= léíáçåë= as the dip switch is recessed, one may put a sticker across the bay to prevent from unauthorized changes. Another option is to completely remove the dip switch. This should be done by authorized service personnel only! It corresponds to all switches set to “off”, i.E. 32db gain and s...
Page 9
Same position. We recommend that you set them to the 0db (full) position. Connect the speaker as shown. Always use channel a’s output connector. Rkpkr= _êáÇÖÉ=ãçåç=ãçÇÉ=ÑÉ~íìêÉë= bridged mono mode combines the power of both channels into one speaker. This results in twice the voltage swing, four tim...
Page 10
Table 1 provides the simplest way to find the best mls tm settings for your application. There is no risk to damage the amplifier since it is very well protected (even down to 0.3 ohms). The fp 2600 amplifier is a power converter, and by selecting mls tm positions you are allocating a portion of the...
Page 11: S= Fkpq^ii^qflk=
S= fkpq^ii^qflk= skn= jçìåíáåÖ= the amplifier is two rack units high (2u) and will fit into a standard eia 19” rack. Amplifiers may be stacked directly on top of each other; there is no need for spacing in between units. If it is the intention to fill a rack with amplifiers, we recommend to start ra...
Page 12
Skr= dêçìåÇáåÖ= there is no ground lift switch or terminal on this amplifier. The signal ground is always floating via a resistor to chassis, and the grounding system is automatic. If a potential above 0.6v is presents in between signal ground and chassis ground, a short circuit is introduced betwee...
Page 13: T= `lkkb`qflkp=
The chart below shows the heat power produced in watts, in kcal per hour, and also in btu per hour. 1/3 power(1)1/8 power (2) 1/3 power(1) 1/8 power (2)1/3 power(1)1/8 power (2) [w] [w] kcal / h kcal / h btu / h btu / h fp 2600 8 ohms 443 373 380 320 1510 1270 4 ohms 770 630 660 540 2630 2150 2 ohms...
Page 14
To daisy-chain amplifiers, use the xlr-male connector provided on each channel, labeled “link”. They are connected in parallel with the neutrik® combojack on each input. Tknko= råÄ~ä~åÅÉÇ=áåéìíë= to connect an unbalanced input source, connect pins 1 and 3 in the cable’s xlr plug (ring and sleeve in ...
Page 15: U= Lmbo^qflk=
U= lmbo^qflk= ukn= léÉê~íáçå=éêÉÅ~ìíáçåë= • make sure that the power switch is set to “off” before connecting any input or output, or operating the switches on the rear panel. See page 10 regarding installation. • make sure that the ac mains voltage is correct, and the same as the one printed on the...
Page 16: V= Molqb`qflk=Cb^qrobp=
V= molqb`qflk=cb^qrobp= each lab.Gruppen amplifier has many advanced protection features. Should a fault condition arise they are protecting both, the amplifier and the speakers connected to it. Under normal use these features are inaudible. All protection circuits work independent from each other. ...
Page 17: Nm=J^fkqbk^k`b=
Vknks= a`=éêçíÉÅíáçå= there are two types of dc protection: • fuses on the supply branches of each channel. • a dc crowbar protection that shorts the output if more than 10 volts dc are being detected on the outputs. Either of these protections comes into effect once dc voltage is being detected, in...
Page 18: Nn=Pmb`fcf`^qflkp=
Nn=pmb`fcf`^qflkp= i~ÄkÖêìééÉå== = = = = ====================== ======================== nt rëÉê=j~åì~ä===Ñm=osmm======sÉêëáçå=mkv========ommpjnmjmt=.
Page 19: No=T^oo^kqv=
No=t^oo^kqv= general this product is manufactured by lab.Gruppen and is warranted to be free from defects in components and factory workmanship under normal use and service for a period of three (3) years from the date of original purchase from an authorised lab.Gruppen dealer. When failing to perfo...