Lab.gruppen FP14000 Technical Data - page 2
Item no. TDS-FP14000_V5
L a b . g r u p p e n a b
▸
S w e d e n
i n t e r n a t i o n a L c o n t a c t
▸
i n f o @ L a b g r u p p e n . c o m | u S & c a n a d a c o n t a c t
▸
i n f o @ t c g - a m e r i c a S . c o m
w w w . l a b g r u p p e n . c o m
General
Number of channels
2
Peak total output both channels driven
14000 W
Peak output voltage per channel
195 V
Max. output current per channel
90 A peak
Max. Output Power
2 ohms
4 ohms
8 ohms
16 ohms
Per ch. (both ch.’s driven)
7000 W
4400 W
2350 W
1200 W
Bridged per ch.
3)
14000 W
8800 W
4700 W
Performance with Gain: 35 dB and VPL: 195 V
THD 20 Hz - 20 kHz for 1 W
THD at 1 kHz and 1 dB below clipping
Signal To Noise Ratio
>112 dBA
Channel separation (Crosstalk) at 1 kHz
>70 dB
Frequency response (1 W into 8 ohms) +0/-3 dB
2 Hz - 34.2 kHz
Input impedance
20 kOhm
Common Mode Rejection (CMR)
>54 dB, 20 Hz to 20 kHz
Output impedance @ 100 Hz
19 mOhm
Voltage Peak Limiter (VPL), max. peak output
VPL, selectable per ch.
195, 170, 140, 116, 100, 80, 66, 54 V
VPL, selectable when bridged
1)
390, 340, 280, 232, 200, 160, 132, 108 V
Voltage Peak Limiter mode (per ch.)
Hard / Soft
Gain and Level
Amplifier gain selectable (all channels)
1)
– rear-panel switches
23, 26, 29, 32, 35, 38, 41, 44 dB
Default gain
38 dB
Level adjustment (per ch.)
Front-panel potentiometer, 31 position detented from -inf to 0 dB
Connectors and Switches
Input connectors (per ch.)
3-pin XLR, electronically balanced
Output connectors (per ch.)
Binding Posts 2-pole
Output bridge mode per two ch.’s
A+B - Ch. A is signal input source
NomadLink network
On board, 2 x RJ45 etherCON
®
connectors, IN and OUT
Intelligent fans (on/off)
Yes, depending on presence of output signal
Power on/off and Remote enable on/off
Individual switches on front-panel
Cooling
Two fans, front-to-rear airflow, temperature controlled speed
Front-panel indicators:
Common
NomadLink network; Power Average Limiter (PAL)
2)
; Power on
Per channel
Signal present / High-impedance; -20 dB, -15 dB, -10 dB and -4 dB output signal;
Voltage Peak Limiter (VPL); Current Peak Limiter (CPL); Very High Frequency (VHF); High temperature; Fault; Mute
Power
Operating voltage, 230 V / 115 V nominal
4)
130-265 V / 65-135 V
Minimum power-up voltage, 230 V / 115 V
171 V / 85 V
Power Average Limiter (PAL)
2)
Yes
Soft start / Inrush Current Draw
Yes / max. 5 A
Mains connector
230 V CE: 16 A, CEE7; 115 V ETL: 30 A Twist lock
Dimensions
W: 483 mm (19”), H: 88 mm (2 U), Overall D: 396 mm (15.6”), Mounting D: 358 mm (14.1”)
Weight
12 kg (26.4 lbs.)
Finish
Black painted steel chassis with black painted steel / aluminum front
Approvals
CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC
Note 1)
: Automatic -6 dB gain compensation when bridging channels.
Note 2)
: PAL can reduce the maximum output power to keep the power supply operating safely, and/or to prevent excessive current draw tripping the mains breaker.
Refer to the FP+ Operation Manual section 7.5.8 Power Average Limiter (PAL) for more information.
Note 3)
: The amplifier will be fully operational at bridge-mode 2 ohm loads, but due to physical constraints in the construction, the max. output power will not be
significanty higher than running individual channels and therefore this mode of operation is not
recommended.
Note 4)
: Separate 230 V or 115 V versions available. Not selectable on the amplifier.
All specifications are subject to change without notice.
Intercooler, NomadLink and Class TD are national and/or international registered trademarks of Lab.gruppen AB. R.SMPS and VPL are trademarks of Lab.gruppen AB. All other
trademarks remain the property of their respective owners. Copyright © 2010 Lab.gruppen AB. All rights reserved.
Specifications FP 14000