- DL manuals
- Lab.gruppen
- Amplifier
- iP Series IP 2100
- User Manual
Lab.gruppen iP Series IP 2100 User Manual
Summary of iP Series IP 2100
Page 1
ám=onmm= rpbo=j^kr^i= =.
Page 2: N= `lkqbkqp=
N= `lkqbkqp= 1 contents .......................................................................................................................................1 2 approvals...................................................................................................................................
Page 3: O= =^mmols^ip=
12 warranty...............................................................................................................................17 o= =^mmols^ip= this equipment conforms to the requirements of the emc directive 89/336/eec, amended by 92/31/eec and 93/68/eec and the requirements of the low ...
Page 4
14. Do not connect an amplifier output in parallel or series with any other amplifier’s output. Do not connect the amplifier output to any other voltage source, such as battery, mains source, or power supply, regardless of whether the amplifier is turned on or off. 15. Do not run the output of any a...
Page 5: Q= Fkqolar`qflk=
Q= fkqolar`qflk= thank you for purchasing a lab.Gruppen power amplifier. This manual contains important information on operating your amplifier correctly and safely. Please take some time and read this manual to familiarize you with the advanced features of this amplifier. Qkn= råé~ÅâáåÖ= carefully ...
Page 6
7. Fan grill filters a grille with foam filters is located on the front panel to prevent dust from entering the amplifier. The grille is removable for easy cleaning of the filter by simply pulling them off. The foam filter should always be used. 8. Carry/protection handle both handles can be used to...
Page 7: R= Ob^o=M^kbi=Cb^qrobp=
R= ob^o=m^kbi=cb^qrobp= before turning the amplifier on please read the following sections to make sure that the unit is set up properly for your specific application. Rkn= d~áå=ëïáíÅÜ= the gain switch located on the rear panel (the central dip-switch) changes the input sensitivity of the amplifier....
Page 8
Rkp= léÉê~íáçå=ãçÇÉë= rkpkn= píÉêÉç=ãçÇÉ= in this mode, both channels operate independently of each other. This is used for all 2-channel modes, such as stereo and bi-amping. Set the two center switches to off position for the stereo mode. The level attenuators on the front panel will control the re...
Page 9: S= Fkpq^ii^qflk=
Rkpkr= _êáÇÖÉ=ãçåç=ãçÇÉ=ÑÉ~íìêÉë= bridged mono mode combines the power of both channels into one speaker. This results in twice the voltage swing, four times the peak power and just less than three times the full power of a single channel. One way to understand the load and power from the amplifier’...
Page 10
Referred to on the label. The warranty will not cover damage caused by connecting to the wrong type of ac mains. If the power plug is not appropriate for your country, it can be cut off and wired to a suitable connector in the following way: black or brown live white or blue neutral green or green/y...
Page 11: T= `lkkb`qflkp=
Able 1. Skskn= `~äÅìä~íáçå= e calculated as in the following example: 4 ohms load on an amplifier to the chart above is then 1150 watts. This chart shows the active he heat power produced is the difference between the power consumption and output power: produced in watts, in kcal per hour, and also ...
Page 12
Figure 4. Xlr input connector figure 5. Xlr balanced within the neutrik® combojack there is a ¼”(6.3mm) phone jack, which is wired in parallel with the xlr. Tip hot ring cold sleeve shield/ground figure 6. ¼” trs plug the input impedance is high enough (20 kohms balanced) to allow ”daisy-chaining”, ...
Page 13: U= Lmbo^qflk=
Tko= `çååÉÅíáåÖ=ëéÉ~âÉêë= speaker connections are made via the two neutrik® nl4fc speakon connectors. The speakon connector is designed for high power speaker connections. It assures the correct polarity, it locks in place and prevents from shock hazard. They are wired in the following manner: the r...
Page 14: V= Molqb`qflk=Cb^qrobp=
Ukp= fåéìí=~ííÉåì~íçêë= the two input level attenuators on the front panel adjust the signal level for their respective amplifier channel in all modes. They are calibrated in db to help setting up active loudspeaker systems or cutting down unwanted noise from the input signal. In bridged mode, both ...
Page 15
Vknko= qÜÉêã~ä=éêçíÉÅíáçå= if the amplifier is driven very hard into a low impedance load, the cooling fans will run at high speed. If the causing conditions continue, the temperature indicator(s) will illuminate indicating that the amplifier is about to go into thermal shutdown. After five seconds ...
Page 16: Nm=J^fkqbk^k`b=
Nm=j^fkqbk^k`b= under normal use the amplifier should provide years of trouble-free service. The only user maintenance required by the user is to vacuum the front grill periodically. In some extreme cases it may be necessary for authorized service personnel to clean the inside of the amplifier. Thes...
Page 17: Nn=Pmb`fcf`^qflkp=
Nn=pmb`fcf`^qflkp= i~ÄkÖêìééÉå== = = = = = ======================== ns rëÉê=j~åì~ä===ám=onmm====sÉêëáçå=mkp======ommpjmojor=.
Page 18: No=T^oo^kqv=
No=t^oo^kqv= general this product is manufactured by lab.Gruppen and is warranted to be free from defects in components and factory workmanship under normal use and service for a period of three (3) years from the date of original purchase from an authorised lab.Gruppen dealer. When failing to perfo...