- DL manuals
- Lab.gruppen
- Amplifier
- iP Series IP 900
- User Manual
Lab.gruppen iP Series IP 900 User Manual
Summary of iP Series IP 900
Page 1
ám=vmm= rpbo=j^kr^i= =.
Page 2: N= `lkqbkqp=
N= `lkqbkqp= 1 contents .......................................................................................................................................1 2 approvals...................................................................................................................................
Page 3: O= =^mmols^ip=
O= =^mmols^ip= this equipment conforms to the requirements of the emc directive 89/336/eec, amended by 92/31/eec and 93/68/eec and the requirements of the low voltage directive 73/23/eec, amended by 93/68/eec. Standard applied emc emission en55103-1, e3 emc immunity en55103-2, e3, with s/n below 1% ...
Page 4
15. Do not run the output of any amplifier back into another channel's input. 16. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way such as: • power-supply cord or plug is damaged • liquid has been spilled into the unit • an obje...
Page 5: Q= Fkqolar`qflk=
Q= fkqolar`qflk= thank you for purchasing a lab.Gruppen power amplifier. This manual contains important information on operating your amplifier correctly and safely. Please take some time and read this manual to familiarize you with the advanced features of this amplifier. Qkn= råé~ÅâáåÖ= carefully ...
Page 6
7. Fan grill filters a grille with foam filters is located on the front panel to prevent dust from entering the amplifier. The grille is removable for easy cleaning of the filter by simply pulling them off. The foam filter should always be used. 8. Carry/protection handle both handles can be used to...
Page 7: R= Ob^o=M^kbi=Cb^qrobp=
R= ob^o=m^kbi=cb^qrobp= before turning the amplifier on please read the following sections to make sure that the unit is set up properly for your specific application. Rkn= d~áå=ëïáíÅÜ= the gain switch located on the rear panel (the central dip-switch) changes the input sensitivity of the amplifier....
Page 8
Rkp= léÉê~íáçå=ãçÇÉë= rkpkn= píÉêÉç=ãçÇÉ= in this mode, both channels operate independently of each other. This is used for all 2-channel modes, such as stereo and bi-amping. Set the two center switches to off position for the stereo mode. The level attenuators on the front panel will control the re...
Page 9: S= Fkpq^ii^qflk=
Rkpkr= _êáÇÖÉ=ãçåç=ãçÇÉ=ÑÉ~íìêÉë= bridged mono mode combines the power of both channels into one speaker. This results in twice the voltage swing, four times the peak power and just less than three times the full power of a single channel. One way to understand the load and power from the amplifier’...
Page 10
Referred to on the label. The warranty will not cover damage caused by connecting to the wrong type of ac mains. If the power plug is not appropriate for your country, it can be cut off and wired to a suitable connector in the following way: black or brown live white or blue neutral green or green/y...
Page 11: T= `lkkb`qflkp=
Able 1. Skrkn= `~äÅìä~íáçå= e calculated as in the following example: 4 ohms load on an amplifier to the chart above is then 570 watts. This chart shows the active he heat power produced is the difference between the power consumption and output power: r produced in watts, in kcal per hour, and also...
Page 12
Figure 4. Xlr input connector figure 5. Xlr balanced ithin the neutrik® combojack there is a ¼”(6.3mm) phone jack, which is wired in parallel with the ip hot round w xlr. T ring cold sleeve shield/g igure 6. ¼” trs plug the input impedance is high enough (20 kohms balanced) to t o daisy chain amplif...
Page 13: U= Lmbo^qflk=
Tko= `çååÉÅíáåÖ=ëéÉ~âÉêë= speaker connections are made via the tw connector is designed for high power sp o neutrik® nl4fc speakon connectors. The speakon eaker connections. It assures the correct polarity, it locks in place th channel a and b outputs, so it’s useful for bridging and bi-amp ge 7 and...
Page 14: V= Molqb`qflk=Cb^qrobp=
Uko= mçïÉêáåÖ=ìé=Ó=pçÑí=ëí~êí= when you power up the amplifier it takes a couple of seconds to check its circuits. This is known as the "soft-start" or "slow-start" sequence. The fans then blow at high speed before going into "idle" and the two bottom green led’s illuminate to show the amplifier is ...
Page 15
Apart from this one exception, lab.Gruppen recommend leaving the clip limiters switched "on" (button depressed). (as a side-effect, once the amplifier comes out of a protect condition, the output level has a slow rise time -the effect is like turning the gain up slowly). Vknko= qÜÉêã~ä=éêçíÉÅíáçå= i...
Page 16: Nm=J^fkqbk^k`b=
Nm=j^fkqbk^k`b= under normal use the amplifier should provide years of trouble-free service. The only user maintenance required by the user is to vacuum the front grill periodically. In some extreme cases it may be necessary for authorized service personnel to clean the inside of the amplifier. Thes...
Page 17: Nn=Pmb`fcf`^qflkp=
Nn=pmb`fcf`^qflkp= i~ÄkÖêìééÉå== = = = = = ======================== ns rëÉê=j~åì~ä===ám=vmm====sÉêëáçå=mkp======ommpjmojor=.
Page 18: No=T^oo^kqv=
No=t^oo^kqv= general this product is manufactured by lab.Gruppen and is warranted to be free from defects in components and factory workmanship under normal use and service for a period of three (3) years from the date of original purchase from an authorised lab.Gruppen dealer. When failing to perfo...