1. DL manuals
  2. Labconco
  3. Washer
  4. 44000 Series
  5. User Manual

Labconco 44000 Series User Manual

Manual is about: SteamScrubber & FlaskScrubber Glassware Washers

Summary of 44000 Series

  • Page 1

    Steamscrubber ® & flaskscrubber ® glassware washers models 44000 series 44200 series 44003 series 44203 series 44004 series 44204 series user’s manual labconco corporation 8811 prospect avenue kansas city, mo 64132-2696 800-821-5525, 816-333-8811 fax 816-363-0130 e-mail labconco@labconco.Com home pa...

  • Page 2

    Copyright information copyright © 2002 labconco corporation. All rights reserved. Labconco corporation 8811 prospect avenue kansas city, missouri 64132 the information contained in this manual and the accompanying product are copyrighted and all rights are reserved by labconco corporation. Labconco ...

  • Page 3

    T t a a b b l l e e o o f f c c o o n n t t e e n n t t s s chapter 1: introduction 1 about this manual 2 typographical conventions 3 your next step 4 chapter 2: prerequisites 5 hot water requirements 6 purified water requirements 6 electrical requirements 7 drain requirements 8 space requirements 8...

  • Page 4

    Chapter 4: using your washer 37 arranging the washer racks 37 the steamscrubber racks 38 lowering the top washer arm and top rack 38 the flaskscrubber rack 41 loading glassware into the flaskscrubber 42 the detergent dispenser 44 filling the neutralizing acid dispenser 46 selecting an operating cycl...

  • Page 5

    P#o%&ct se#+ice -./00.122.341/ 1 c c h h a a p p t t e e r r 1 1 i i n n t t r r o o d d u u c c t t i i o o n n congratulations on your purchase of a labconco 5lassware washer. Labconco manufactures two types of 5lassware washers, the steamscrubber and the flaskscrubber . Each of these washers is a...

  • Page 6: About This Manual

    Chapter 1: introduction p#o%&ct se#+ice -./00.122.341/ 2 about this manual this manual is designed to help you learn how to install, use, and maintain your 5lassware washer. Instructions for performing routine maintenance and making minor modifications to your washer are also included. Chapter 1: in...

  • Page 7: Typographical Conventions

    3 p#o%&ct se#+ice -./00.122.341/ chapter 1: introduction chapter 7: troubleshooting contains a table of problems you may encounter while using your 5lassware washer, including the probable causes of the problems, and suggested corrective actions. Appendix a: flaskscrubber and steamscrubber component...

  • Page 8: Your Next Step

    Chapter 1: introduction p#o%&ct se#+ice -./00.122.341/ 4 • important information is presented in capitalized type in paragraphs that are preceded by the pointer icon. It is imperative that the information contained in these paragraphs be thoroughly read and understood by the user. • information that...

  • Page 9

    P#o%&ct se#+ice -./00.122.341/ 5 c c h h a a p p t t e e r r 2 2 p p r r e e r r e e q q u u i i s s i i t t e e s s before you install your 5lassware washer, you need to prepare your site for installation. Carefully examine the location where you intend to install your 5lassware washer. You must be...

  • Page 10: Hot Water Requirements

    Chapter 2: prerequisites chapter 2: prerequisites p#o%&ct se#+ice -./00.122.341/ 6 refer to appendix c: glassware washer specifications for complete 5lassware washer electrical and environmental conditions, specifications and requirements. Hot water requirements an existing hot water supply may be u...

  • Page 11: Electrical Requirements

    7 p#o%&ct se#+ice -./00.122.341/ chapter 2: prerequisites a male e " - 11-1b2 nh hose coupling. A rigid plastic, tin- lined, or stainless steel tubing and fitting can be connected to the washer fitting. All connections on the purified water system must be airtight so that the washer pump is not allo...

  • Page 12: Drain Requirements

    Chapter 2: prerequisites chapter 2: prerequisites p#o%&ct se#+ice -./00.122.341/ 8 drain requirements the 5lassware washer drain hose connects to a fitting on the rear side of the pumpbmotor assembly. The drain hose is installed at the factory prior to shipment. The hose provides a flexible coupling...

  • Page 13: Your Next Step

    9 p#o%&ct se#+ice -./00.122.341/ chapter 2: prerequisites your next step after you have determined that the location for your 5lassware washer accommodates the installation and operational requirements of your washer, you are ready to unpack and install your washer. Proceed to chapter 3: getting sta...

  • Page 14

    Chapter 2: prerequisites chapter 2: prerequisites p#o%&ct se#+ice -./00.122.341/ 10

  • Page 15

    P#o%&ct se#+ice -./00.122.341/ 11 c c h h a a p p t t e e r r 3 3 g g e e t t t t i i n n g g s s t t a a r r t t e e d d now that the site for your 5lassware washer is properly prepared, you are ready to unpack, inspect, install, and test your washer. Read this chapter to learn how to: • unpack and...

  • Page 16: Unpacking Your Glassware

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 12 unpacking your glassware washer carefully unpack your 5lassware washer and inspect the washer for damage that may have occurred in transit. If your washer is damaged, notify the delivery carrier immediately and ret...

  • Page 17: Washer Components

    Chapter 3: getting started 13 p#o%&ct se#+ice -./00.122.341/ washer components as previously mentioned, labconco manufactures two types of 5lassware washers, the steamscrubber and the flaskscrubber. Each of these washers is available in a mobile, undercounter, and freestanding model. Each washer mod...

  • Page 18

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 14 catalog h washer description 44004-00 steamscrubber freestanding i 115 v 44004-01 steamscrubber freestanding i 230 v 44004-10 steamscrubber freestanding i 115 v with window 44004-11 steamscrubber freestanding i 230...

  • Page 19: Setting Up Your Washer

    Chapter 3: getting started 15 p#o%&ct se#+ice -./00.122.341/ catalog h washer description 44204-00 flaskscrubber freestanding i 115 v 44204-01 flaskscrubber freestanding i 230 v 44204-10 flaskscrubber freestanding i 115 v with window 44204-11 flaskscrubber freestanding i 230 v with window plus the f...

  • Page 20: Feet

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 16 model, then you must level the washer and center the washer door. If you have an undercounter model, you must also attach the washer to the countertop or worksurface. Installing the casters or leveling feet if you ...

  • Page 21

    Chapter 3: getting started 17 p#o%&ct se#+ice -./00.122.341/ if you have the undercounter or freestanding model of the steamscrubber or flaskscrubber washer, refer to figure 3-2 and follow the steps detailed below to install the leveling feet on your washer. To install the leveling feet: 1. Locate t...

  • Page 22: Leveling The Washer

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 18 leveling the washer if you have the freestanding model of the steamscrubber or flaskscrubber 5lassware washer, after you have installed the leveling feet, you must level the washer by adjusting the leveling feet. T...

  • Page 23

    Chapter 3: getting started 19 p#o%&ct se#+ice -./00.122.341/ if you have the undercounter model, you may level it side-to-side by placing a short level on the inside top edge of the door. Refer to figure 3-5 for the placement of the level on the washer. U u position the level as shown to level the u...

  • Page 24: Centering The Washer Door

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 20 centering the washer door when the washer is level, check the operation of the washer door for alignment with the washer tank. If the door is not centered in the opening, you must center the door by adjusting the c...

  • Page 25: Connecting The Water

    Chapter 3: getting started 21 p#o%&ct se#+ice -./00.122.341/ connecting the water supplies a hot water supply must be attached to your 5lassware washer. If you need purified water for the final rinse cycle, then you must also connect a purified water source to your washer. Connecting the hot water t...

  • Page 26

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 22 after you remove the lower panel, you are ready to connect the hot water source. Refer to figure 3-8 and follow the instructions below to connect the hot water. You must provide the plumbin5 fittin5s and components...

  • Page 27: Supply

    Chapter 3: getting started 23 p#o%&ct se#+ice -./00.122.341/ connecting the purified water supply to prevent valve and pump clogging, flush all of the water lines for your purified water supply source prior to connecting the washer to the water lines. The water supply valve to which the purified wat...

  • Page 28

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 24 at least 1.25 5allons p4.7 litersq per minute of purified water flow is required. At least 5 5allons of purified water must be available for each wash cycle. A 3b8 " id pipe is the minimum recommended. If the washe...

  • Page 29

    Chapter 3: getting started 25 p#o%&ct se#+ice -./00.122.341/ purified water pump clamp weight to hose to keep it submerged. Cut hose into a v configuration for siphoning. Spigot purified water pump open for vent example of a bottom feed connection example of a top feed connection figure 3-10 figure ...

  • Page 30: Installing Faucet Adapters

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 26 mahe certain that all of the connections on the purified water system are air ti5ht. The pump must not pull air instead of water. Mahe certain the supply hose is not crimped. Installing faucet adapters if you purch...

  • Page 31: Att6C7Ing T7E :o;e.En%

    Chapter 3: getting started 27 p#o%&ct se#+ice -./00.122.341/ an aerator adapter and a standard-size adapter fitting are provided with your mobile washer. If the adapter fitting provided does not allow for a tight connection to your faucet, a variety of internally and externally threaded fittings are...

  • Page 32

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 28 tubing or pipe f " p1.3 cmq id should be used for the drain. Do not route the drain to an elevation more than 30 " p76 cmq above the pump dischar5e. Do not reduce the sige of the drain plumbin5. Do not remove the h...

  • Page 33

    Chapter 3: getting started 29 p#o%&ct se#+ice -./00.122.341/ if you route the drain piping to a sink drain and use an air gap, refer to figure 3-14 for the placement of the air gap. Air gap drain line figure 3-14.

  • Page 34

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 30 if you route the drain piping to a floor drain, refer to figure 3-15 for placement of the drain tubing and trap. Connecting the power supply before continuing with this section, be certain your power supply meets t...

  • Page 35

    Chapter 3: getting started 31 p#o%&ct se#+ice -./00.122.341/ the supply circuit must consist of number 12 aw5 3-wire cable or heavier. Washers must be connected to a service with a 20 amp circuit breaher or fuse. To connect the electrical supply: 1. Remove the lower panel on the washer by removing t...

  • Page 36: Testing Your Washer

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 32 before turnin5 on the washer, mahe certain the water is turned on and no pachin5 material remains inside the washer. Testing your washer now that you have made the required water and electrical connections to your ...

  • Page 37: Connecting The Hose-End

    Chapter 3: getting started 33 p#o%&ct se#+ice -./00.122.341/ connecting the hose-end coupling if you purchased a mobile 5lassware washer, the first action you must take is to connect the hose-end coupling to the hot water faucet. Snap the hose-end coupling onto the aerator adapter on the faucet by p...

  • Page 38

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 34 before operatin5 the washer with the purified water option selected, chech the purified water supply for ample quantity. To run the diagnostics test : 1. Locate the control panel on the front of your washer. 2. Pre...

  • Page 39: Disconnecting The Hose-End

    Chapter 3: getting started 35 p#o%&ct se#+ice -./00.122.341/ 18. Press the select program button. 19. The display window should read: heat i hi5h tpstat and the heater activates. 20. Press the select program button. 21. The display window should read: heat i low tpstat and the heater activates. 22. ...

  • Page 40: Your Next Step

    Chapter 2: prerequisites chapter 3: getting started p#o%&ct se#+ice -./00.122.341/ 36 to disconnect the hose-end coupling : 1. Turn off the hot water faucet. 2. Push the pressure relief button on the hose-end coupling to relieve the water pressure. 3. Pull down on the plastic release ring on the hos...

  • Page 41

    P#o%&ct se#+ice -./00.122.341/ 37 c c h h a a p p t t e e r r 4 4 u u s s i i n n g g y y o o u u r r w w a a s s h h e e r r after your washer has passed the basic diagnostics test detailed in chapter 3: getting started , you are ready to begin using your washer. Read this chapter to learn how to: ...

  • Page 42: The Steamscrubber Racks

    Chapter 2: prerequisites chapter 4: using your washer p#o%&ct se#+ice -./00.122.341/ 38 best suit your needs. For a complete list of available rack accessories, refer to appendix d: glassware washer accessories . If you purchased a steamscrubber, proceed to the following section, the steamscrubber r...

  • Page 43

    Chapter 4: using your washer 39 p#o%&ct se#+ice -./00.122.341/ to lower the top washer arm and the top rack of the steamscrubber: 1. Open the washer door by sliding the latch knob to the left. Pull the door toward you and down. 2. Depress the button on the right side of the upper wash arm tower, as ...

  • Page 44

    Chapter 2: prerequisites chapter 4: using your washer p#o%&ct se#+ice -./00.122.341/ 40 6. Pull the upper rack forward and lift the front until the wheels disengage from the track. 7. With a twisting motion, remove the rails from the rollers on each side of the tank, as shown above in figure 4-2. 8....

  • Page 45: The Flaskscrubber Rack

    Chapter 4: using your washer 41 p#o%&ct se#+ice -./00.122.341/ the flaskscrubber rack the flaskscrubber 5lassware washer is equipped with a spindle rack and four glassware holders. The flaskscrubber spindle rack is designed for narrow-necked glassware such as volumetric flasks, erlenmeyer flasks, gr...

  • Page 46: Flaskscrubber

    Chapter 2: prerequisites chapter 4: using your washer p#o%&ct se#+ice -./00.122.341/ 42 if the multi-pin insert is installed on the bottom rach and the optional upper rach is used, do not heavily load the multi-pin insert with wide mouth 5lassware. This may restrict water flow from the lower distrib...

  • Page 47

    Chapter 4: using your washer 43 p#o%&ct se#+ice -./00.122.341/ two large and two small 5lassware holders are supplied with each flaskscrubber. These holders enable you to place wide-mouth glassware onto the flaskscrubber spindles. To position glassware in a glassware holder and install the holder on...

  • Page 48: The Detergent Dispenser

    Chapter 2: prerequisites chapter 4: using your washer p#o%&ct se#+ice -./00.122.341/ 44 5lassware should be loaded so that it does not touch each other during a wash cycle. The washer has been designed for quiet operation. To prevent noise and glass breakage, be certain that the glassware does not t...

  • Page 49

    Chapter 4: using your washer 45 p#o%&ct se#+ice -./00.122.341/ the detergent dispenser opens during the second wash cycle, except when the plastic cycle is selected, which has only one wash cycle. If your glassware is heavily soiled, you may want to add powder detergent to the pre-wash cavity. Do no...

  • Page 50: Dispenser

    Chapter 2: prerequisites chapter 4: using your washer p#o%&ct se#+ice -./00.122.341/ 46 fill the main detergent cavity three-fourths full if the water hardness grains per gallon p5p5q for your water measures 0 i 4 5p5 psoft waterq. Fill the detergent cavity completely if your water measures 4 5p5 or...

  • Page 51: Wash Cycle

    Chapter 4: using your washer 47 p#o%&ct se#+ice -./00.122.341/ selecting an operating cycle the microprocessor control on your 5lassware washer allows you to select one of four factory preset wash cycles, to custom program two additional cycles, or to run a rinse- only cycle. The control panel is sh...

  • Page 52

    Chapter 2: prerequisites chapter 4: using your washer p#o%&ct se#+ice -./00.122.341/ 48 washers built for use on 230v have the capability to wash glassware at a temperature of 180[f p82[cq. They also are able to operate at the lower temperature of 140[f p60[cq which is the standard temperature of th...

  • Page 53: Interrupting A Wash Cycle

    Chapter 4: using your washer 49 p#o%&ct se#+ice -./00.122.341/ if steam operation is needed, press the corresponding button. In this mode, the 5lassware washer will refill with fresh water after the completion of wash 1. Both the sump and steam heaters will operate for 10 minutes to produce hot vapo...

  • Page 54

    Chapter 2: prerequisites chapter 4: using your washer p#o%&ct se#+ice -./00.122.341/ 50

  • Page 55: Maintaining The Stainless

    P#o%&ct se#+ice -./00.122.341/ 51 c c h h a a p p t t e e r r 5 5 m m a a i i n n t t a a i i n n i i n n g g y y o o u u r r w w a a s s h h e e r r under normal operation, your 5lassware washer will require little routine maintenance to keep it functioning properly. Read this chapter to learn how ...

  • Page 56

    Chapter 2: prerequisites chapter 5: maintaining your washer p#o%&ct se#+ice -./00.122.341/ 52 to maintain the appearance and quality of the stainless steel interior, perform the following tasks as needed: • wipe the outer edges on the inside door panel to remove particles and residue that occur duri...

  • Page 57: Maintaining The Air Gap

    Chapter 5: maintaining your washer 53 p#o%&ct se#+ice -./00.122.341/ maintaining the air gap if you employed an air gap during the installation of your washer, you need to clean the air gap at least once a month. The air gap is not part of the washerd therefore, it is not covered by the washer warra...

  • Page 58: Maintaining The Overflow

    Chapter 2: prerequisites chapter 5: maintaining your washer p#o%&ct se#+ice -./00.122.341/ 54 to clean the water fill valve: 1. Turn off the water and electricity to the washer. Unplug the mobile modeld turn off the circuit breaker that services the undercounter or freestanding model. 2. Remove the ...

  • Page 59

    Chapter 5: maintaining your washer 55 p#o%&ct se#+ice -./00.122.341/ to clean the overflow dome: 1. Turn off electrical power to the 5lassware washer. 2. Remove the two screws at the bottom of the lower panel of your washer. 3. Remove the panel by lifting slightly and pulling out. 4. Locate the gray...

  • Page 60: Bulb

    Chapter 2: prerequisites chapter 5: maintaining your washer p#o%&ct se#+ice -./00.122.341/ 56 replacing the washer light bulb if your 5lassware washer is equipped with a window, you will need to periodically replace the 25-watt washer light bulb. Refer to figure 5-3 and follow the instructions below...

  • Page 61: Removing The Washer Top,

    Chapter 5: maintaining your washer 57 p#o%&ct se#+ice -./00.122.341/ removing the washer top, back, and side panels there may be times when you need to remove the washer top, back, and side panels to clean, maintain, or repair your washer. Refer to figure 5-4 and follow the instructions below to rem...

  • Page 62: Cleaning The Sump Filter

    Chapter 2: prerequisites chapter 5: maintaining your washer p#o%&ct se#+ice -./00.122.341/ 58 cleaning the sump filter screen if debris accumulates on the filter screen that is located in the washer sump, you can remove and clean the screen. To clean the sump filter screen, refer to figure 5-5 and f...

  • Page 63: Disconnecting The Purified

    P#o%&ct se#+ice -./00.122.341/ 59 c c h h a a p p t t e e r r 6 6 m m o o d d i i f f y y i i n n g g y y o o u u r r w w a a s s h h e e r r the configuration of your washer may need to be changed to accommodate your needs. For example, you may want to disconnect the purified water pump, install pi...

  • Page 64: Flaskscrubber Options

    Chapter 2: prerequisites chapter 6: modifying your washer p#o%&ct se#+ice -./00.122.341/ 60 to disconnect the purified water pump: 1. Disconnect the washer from its electrical source. 2. Remove the two screws at the bottom of the lower panel of your washer. 3. Remove the panel by lifting slightly an...

  • Page 65: Flaskscrubber

    Chapter 6: modifying your washer 61 p#o%&ct se#+ice -./00.122.341/ installing pipet inserts in a flaskscrubber two sizes of pipet inserts are available. The 8-place pipet insert, shown in figure 6-2 accommodates 1 ml to 10 ml pipets. Multiple pipet inserts may be installed, if desired. Refer to figu...

  • Page 66

    Chapter 2: prerequisites chapter 6: modifying your washer p#o%&ct se#+ice -./00.122.341/ 62 the 14-place pipet insert, shown in figure 6-3, accommodates 1 ml to 50 ml pipets. Two of these inserts may be installed, if desired. Refer to figure 6-3 and follow the instructions below to install a 14-plac...

  • Page 67: Installing The Optional

    Chapter 6: modifying your washer 63 p#o%&ct se#+ice -./00.122.341/ installing the optional adjustable-height upper rack an optional top rack, shown in figure 6-6, is available to increase the capacity of the flaskscrubber to handle wide- mouth glassware, including beakers. To install the optional to...

  • Page 68

    Chapter 2: prerequisites chapter 6: modifying your washer p#o%&ct se#+ice -./00.122.341/ 64 4. Install the left and right rails by tilting the top of the rails between the rollers on the sides of the washer tank and push the bottoms of the rails into place, as illustrated in figure 6-5. Install both...

  • Page 69

    Chapter 6: modifying your washer 65 p#o%&ct se#+ice -./00.122.341/ figure 6-5 tilt and position the top of the rail between the factory-installed rollers and then push the bottom of the rail into place. Install a rubber bumper on the end of the rail. Figure 6-6 basket inserts top rack frame.

  • Page 70: Spindle Rack

    Chapter 2: prerequisites chapter 6: modifying your washer p#o%&ct se#+ice -./00.122.341/ 66 installing the optional upper spindle rack the upper spindle rack expands the capability of the flaskscrubber by providing 24 additional spindles for washing narrow-neck glassware. The rack may be customized ...

  • Page 71

    Chapter 6: modifying your washer 67 p#o%&ct se#+ice -./00.122.341/ b. Install the upper rails and the upper spindle rack. See figure 6-8. 1. Install the rear rubber bumpers to the ends of the rails. 2. Install the left and right rails by tilting the top of the rails between the rollers on the side o...

  • Page 72: Rack

    Chapter 2: prerequisites chapter 6: modifying your washer p#o%&ct se#+ice -./00.122.341/ 68 c. Adjust the rubber diaphragm the rubber diaphragm, that is on the upper supply tube assembly installed in step a, should almost touch the lower portion of the hub in the upper spindle rack when both racks a...

  • Page 73

    Chapter 6: modifying your washer 69 p#o%&ct se#+ice -./00.122.341/ if the multi-pin insert is installed on the bottom rach and the optional upper rach is used, do not heavily load the multi-pin insert with wide mouth 5lassware. This may restrict water flow from the lower distribution arm to the 5las...

  • Page 74

    Chapter 2: prerequisites chapter 6: modifying your washer p#o%&ct se#+ice -./00.122.341/ 70

  • Page 75

    P#o%&ct se#+ice -./00.122.341/ 71 c c h h a a p p t t e e r r 7 7 t t r r o o u u b b l l e e s s h h o o o o t t i i n n g g refer to the following table if your 5lassware washer fails to operate properly. If the suggested corrective actions do not solve your problem, contact labconco for additiona...

  • Page 76

    Chapter 2: prerequisites chapter 7: troubleshooting p#o%&ct se#+ice -./00.122.341/ 72 problem cause corrective action door drops too far (below door stop) bent door hinge replace door hinge. Poor drying water is not hot enough check inlet water temperature pminimum 120[ fq at the washer. Flask, beak...

  • Page 77

    Chapter 7: troubleshooting 73 p#o%&ct se#+ice -./00.122.341/ problem cause corrective action not draining properly clogged filter clean sump filter. Drain line clogged or kinked disconnect drain line and clean or remove kink. Purified water does not fill crimp in supply hose refer to installation in...

  • Page 78

    Chapter 2: prerequisites chapter 7: troubleshooting p#o%&ct se#+ice -./00.122.341/ 74 problem cause corrective action washer leaks (cont.) fill tube out of trap reinstall fill tube. Loose connection at fill valve check fill valve and correct. Improper detergent use non-foaming detergent. Use only pr...

  • Page 79

    Chapter 7: troubleshooting 75 p#o%&ct se#+ice -./00.122.341/.

  • Page 80

    P#o%&ct se#+ice -./00.122.341/ 76 a a p p p p e e n n d d i i x x a a f f l l a a s s k k s s c c r r u u b b b b e e r r a a n n d d s s t t e e a a m m s s c c r r u u b b b b e e r r c c o o m m p p o o n n e e n n t t s s the following components are available for your 5lassware washer. The flas...

  • Page 81

    Appendix a: flaskscrubber and steamscrubber components 77 p#o%&ct se#+ice -./00.122.341/ figure a-1.

  • Page 82

    Chapter 2: prerequisites appendix a: flaskscrubber and steamscrubber components p#o%&ct se#+ice -./00.122.341/ 78 ite m part # 115v part # 230v quantity description 1 44447-00 44447-00 1 upper basket rail pr.H.Q 1a 44451-00 44451-00 1 upper basket rail pl.H.Q 2 44352-00 44352-00 1 overflow dome 3 44...

  • Page 83

    Appendix a: flaskscrubber and steamscrubber components 79 p#o%&ct se#+ice -./00.122.341/ figure a-2.

  • Page 84: Freestanding Washer

    P#o%&ct se#+ice -./00.122.341/ 80 a a p p p p e e n n d d i i x x b b g g l l a a s s s s w w a a r r e e w w a a s s h h e e r r d d i i m m e e n n s s i i o o n n s s freestanding washer figure b-1 english: inch figure b-2 metric: cm.

  • Page 85: Mobile Washer

    Appendix b: glassware washer dimensions 81 p#o%&ct se#+ice -./00.122.341/ mobile washer interior - all steamscrubber models figure b-3 figure b-4 english: inch metric: cm.

  • Page 86: Undercounter Washer

    Chapter 2: prerequisites appendix b: glassware washer dimensions p#o%&ct se#+ice -./00.122.341/ 82 undercounter washer interior - all steamscrubber figure b-5 figure b-6 english: inch metric: cm.

  • Page 87

    Appendix b: glassware washer dimensions 83 p#o%&ct se#+ice -./00.122.341/ interior - all steamscrubbers interior - all flaskscrubbers figure b-7 figure b-8.

  • Page 88: Upper Spindle Rack

    Chapter 2: prerequisites appendix b: glassware washer dimensions p#o%&ct se#+ice -./00.122.341/ 84 interior – all flaskscrubbers with accessory upper spindle rack flaskscrubber basic spray pattern figure b-9 figure b-8a.

  • Page 89: Rack And Hub Adapter

    Appendix b: glassware washer dimensions 85 p#o%&ct se#+ice -./00.122.341/ flaskscrubber spray pattern with accessory top rack and hub adapter flaskscrubber spray pattern with accessory upper spindle rack steamscrubber spray pattern figure b-10 figure b-12 figure b-11.

  • Page 90

    Chapter 2: prerequisites appendix b: glassware washer dimensions p#o%&ct se#+ice -./00.122.341/ 86.

  • Page 91

    Appendix b: glassware washer dimensions 87 p#o%&ct se#+ice -./00.122.341/.

  • Page 92

    P#o%&ct se#+ice -./00.122.341/ 88 a a p p p p e e n n d d i i x x c c g g l l a a s s s s w w a a r r e e w w a a s s h h e e r r s s p p e e c c i i f f i i c c a a t t i i o o n n s s this appendix contains various specifications for the 5lassware washer, including program times and water consumpt...

  • Page 93

    Appendix c: glassware washer specifications 89 p#o%&ct se#+ice -./00.122.341/ • indoor use only. • maximum altitude: 6562 feet p2000 metersq. • ambient temperature range: 41[ to 104[f p5[ to 40[cq. • maximum relative humidity: 80q for temperatures up to 88[f p31[cq, decreasing linearly to 50q relati...

  • Page 94: (115V Models)

    Chapter 2: prerequisites appendix c: glassware washer specifications p#o%&ct se#+ice -./00.122.341/ 90 program times and water consumption (115v models) program rinse only plastic glass glass plus scientific user 1 set user 2 set wash 1 - 5 5 5 5 5 steam - - t t 10 t 10 wash 2 - 10 20u 30u 40u 10u 1...

  • Page 95: (230V Models)

    Appendix c: glassware washer specifications 91 p#o%&ct se#+ice -./00.122.341/ program times and water consumption (230v models) program rinse only plastic lo heat glass lo heat glass plus hi heat scientific hi heat user 1 set lo heat user 2 set hi heat wash 1 - 5 5 5 5 5 steam - - t t 10 t 10 wash 2...

  • Page 96

    Chapter 2: prerequisites appendix c: glassware washer specifications p#o%&ct se#+ice -./00.122.341/ 92 wiring diagram (115v models).

  • Page 97

    Appendix c: glassware washer specifications 93 p#o%&ct se#+ice -./00.122.341/ wiring diagram (230v models.

  • Page 98: Accessories

    P#o%&ct se#+ice -./00.122.341/ 94 a a p p p p e e n n d d i i x x d d g g l l a a s s s s w w a a r r e e w w a a s s h h e e r r a a c c c c e e s s s s o o r r i i e e s s accessories part h description 45250-00 upper spindle rack \ stainless steel. Contains one upper spindle rack with 24 spindles...

  • Page 99

    Appendix d: glassware washer accessories 95 p#o%&ct se#+ice -./00.122.341/ part h description 44049-01 multi-pin insert \ stainless steel . For use with beakers, erlenmeyer flasks, and wide-mouth glassware. For placement in bottom rack. 44022-01 utensil basket \ stainless steel. For miscellaneous la...

  • Page 100

    Chapter 2: prerequisites appendix d: glassware washer accessories p#o%&ct se#+ice -./00.122.341/ 96 part h description 44246-00 44248-00 glassware holder \ small . 5rips wide-mouth glassware over spindles. Glassware holder \ large . 5rips wide-mouth glassware over spindles. 91002-00 interconnect @it...

  • Page 101

    Appendix d: glassware washer accessories 97 p#o%&ct se#+ice -./00.122.341/ part h description 45800-00 stand . For use with freestanding and mobile models. Raises washer approximately 17 inches. Front opens to provide storage underneath washer..

  • Page 102: Steamscrubber Accessories

    Chapter 2: prerequisites appendix d: glassware washer accessories p#o%&ct se#+ice -./00.122.341/ 98 steamscrubber accessories part h description 44016-01 44020-01 44021-01 4401301 culture tube/test tube insert \ stainless steel . Insert for 10 mm to 12 mm tubes. Culture tube/test tube insert \ stain...

  • Page 103

    Appendix d: glassware washer accessories 99 p#o%&ct se#+ice -./00.122.341/ part h description 44015-01 10-pin insert \ stainless steel . For use with beakers, erlenmeyer flasks, and other wide- mouth glassware. 44018-01 32-pin insert \ stainless steel . For use with beakers, erlenmeyer flasks, and o...

  • Page 104

    Chapter 2: prerequisites appendix d: glassware washer accessories p#o%&ct se#+ice -./00.122.341/ 100 part h description 44048-01 bod rack/beaker/ erlenmeyer flask insert \ stainless steel . Rack secures glassware used in oxygen-demand determination, beakers, and erlenmeyer flasks. 44022-01 utensil b...

  • Page 105

    Appendix d: glassware washer accessories 101 p#o%&ct se#+ice -./00.122.341/ part h description 44012-02 bottom rack \ stainless steel . Included with washer. 91002-00 interconnect @it . Allows waterpro ro station to be attached to the washer. 90750-00 90750-02 waterpro ro station . Provides purified...

  • Page 106: Expendables

    Chapter 2: prerequisites appendix d: glassware washer accessories p#o%&ct se#+ice -./00.122.341/ 102 part h description 45800-00 stand . For use with freestanding and mobile models. Raises washer approximately 17 inches. Front opens to provide storage underneath washer. Expendables part h descriptio...

  • Page 107

    P#o%&ct se#+ice -./00.122.341/ 103.