© design and specifications are subject to change without notice 2010 all rights reserved. Please save this manual for future reference owner manual ® ® tm cleanjet , la lili chair 9600 foot-spa chair 9700 tm patent #d610697, #d600950 patent pending.
Table of contents safety and precautions installations attaching seat jet assembly plumbing connections 1-2 identifying parts 3-4 7 8-9 warranty & service 14 6 owner manual operations and use cleaning & maintenance 10-11 12-13 foot-spa clearance 5.
Safety & precaution 1 thank you for purchasing the la lili spa from gulfstream inc. Please carefully read the instructions before installing the spa. Carefully follow the instructions, your spa will give you years of beauty and service. This product is to be connected to a branch circuit outlet prot...
Safety & precaution 2 grounding methods because this unit must be connected to a circuit with a ground-fault circuit interrupter (gfci), do not use a grounding adapter. The use of a grounding adapter is prohibited in canada by part i of the canadian electrical code. Grounding instructions this appli...
11 10 front back identify your foot-spa 3 1 8 5 6 7 4 3 2 12 13 14 1. Tub & glass insert 2. Adjustable footrest 3. Seat cushion 4. Flip-out manicure tray 5. Back cushion & massage 6. Headrest pillow 7. Wooden armrest 8. Hand spray model # st700.20 9. Front control panel 10. Drain 11. Jet 2x 12. Drai...
4 identify your foot-spa 1 2 3 armrest can be raised up/down reclining sliding 5 ’ 5’ 7’’ 2 32 ’’ 43’’ 15’’ seat operation spa dimension.
5 foot-spa clearance wall 16’’ 60’’ 60’’ 16’’ 16’’ 28’’ foot-spa #1 center center foot-spa #2 typical foot-spas clearance wall clearance.
6 installations align the seat with the pre-drilled holes on the base then tightly secure with the nuts and bolts provided. Attach trays or remote stand to armrest with screws provided attaching the seat to the base.
7 installations cleanjet unit removal plate & anchors located on tub/bowl wall impeller housing top plate wall ball washer anchor pins to remove the jet unit from tub/bowl. Gently pull out the jet unit from the anchor pins to remove the jet unit components. Turn the top plate counter-clockwise in th...
Installations 8 1. Discharge pump may be connected to an existing sink drain or floor drain. It can also pump up to 7 ft high, but this will increase the length of the drain time. The drain connection is at the rear of the unit by a 3/4” fitting. 2. Gravity drain uses a standard gravity drain. A flo...
Installations 9 gfi outlet required existing drain pipe discharge pump drain elbow oo fl r wall 16’’ - 2 ’ 4’ f t- le th oo spa ng ½” hot & cold hoses typical discharge pump installation gfi outlet required existing drain pipe minimum slope of 1/4’’ per foot to sewer line p-trap oo fl r wall 16 ’ - ...
1. To fill water: the foot-spa is provided with a single hot and cold mixing valve located on the front of your spa. This is a pressure balance valve that requires you to lift the handle to start the water flow and to adjust to the temperature that is desired. The clean jet motor must be completely ...
Operations & use 11 9620, 9700, 9600 shiatsu remote control please refer to instruction manual for operations lcd timing auto neck shoulder power pause kneading knocking width lower adjustment incline seat forward seat backward recline intensity air on/off back waist kneading upper adjustment speed ...
Gulfstream inc. Highly recommends the following cleaning regimen. You should always contact your local governing agency for their specific cleaning and disinfecting requirements and regulations for pedicure spas. For your clients safety, always use the regulations as a minimum standard for cleaning ...
Cleaning & maintenance 13 cleaning the magnet jet (step by step) 1. Pull magnet jet off from the pedicure bowl 2. Turn the top plate of the magnet jet counter-clockwise 3. Separate the three components of the magnet jet: top plate, magnet, back plate 4. Wash each component of the magnet jet in a rec...
