1. DL manuals
  2. Lamborghini Caloreclima
  3. Burner
  4. GP 20
  5. Installation And Maintenance Manual

Lamborghini Caloreclima GP 20 Installation And Maintenance Manual

Manual is about: pellet

Summary of GP 20

  • Page 1

    Bruciatore a pellet pellet burner brÛleur À pellets gp 20 libretto di installazione e manutenzione installation and maintenance manual notice d’installation et d’entretien.

  • Page 2

    English - 2 - please read the instructions carefully as they provide important information about the safety, installation, use and maintenance of the burner. Keep the manual in a safe place for future consultation. Installation must be carried out by qualified personnel in conformance with technical...

  • Page 3

    English general - 2 - content general introduction page 26 applicationfield “ 26 technicaldata “ 26 safety “ 26 descriptionoftheconstruction “ 28 mainknotsandmechanisms “ 29 sparepartslist “ 30 positionoftheelements “ 31 installation connectingtotheboiler page 34 connectingtotheelectricalnetwork “ 3...

  • Page 4

    General - 2 - introduction the present manual is designed for those who will use the pellet burner. You will find inside the necessary mounting, star- ting, maintenance and safety data for the device. We recommend to keep our instructions about the safety measures with a special responsibility. Oper...

  • Page 5

    English general - 2 - • it is absolutely forbidden the eliminating of this protection since it is directly connected to the fire safety. • the contact between the burner and the boiler should be well tight in order to prevent gas leaks in the service room. • when installing the system, it should be ...

  • Page 6

    General - 2 - description of the construction 40° 2 4 220 165 251 34 178 272 5 1 1 burner 2 auger transporter 3 flexible tube.

  • Page 7

    English general - 2 - main knots and mechanism the general appearance of the burner together with the feeding auger are shown on fig. The set contains mainly the following composition parts: - burner - auger transporter - flexible tube - body, feeding chute and cover - fan - ignite heater - control ...

  • Page 8

    General - 0 - spare parts list in correspondence with any of our sales representatives regarding the bought burner, please provide the following infor- mation: 1. Serial number; 2. Working voltage and electricity frequency; 3. Delivery date; 4. Detailed description of the eventual damage; 5. The sum...

  • Page 9

    English general - 1 - position of the elements.

  • Page 10

    General - 2 -.

  • Page 11

    English general - -.

  • Page 12

    Installation - - connecting to the boiler • the device should be placed a in way, so there will be enough space for cleaning, removing the soot from the burner, the boiler and the draught pipes. • the burner must be installed in the boiler outlet with the relevant isolation. It must be joined up wit...

  • Page 13

    English installation - - electrical diagram boiler working thermostat start burner - signal from the boiler alarm thermostat brown black power 220 v~ neutral conduct blue yellow/green first feeding of the auger start burner –signal for logic module photosensor photocell flame detector feeding and fi...

  • Page 14

    Installation - - getting in operation the device can start only if it is connected to the boiler by a chimney, providing enough traction, there is a pressure and pellets from the pellet transporter. Requirements for supplying pellets during the burner start: - the auger transporter must be placed in...

  • Page 15

    English installation - - - if more than few attempts for ignition appear unsuccessful, for example if the fuel ends (parameter c1, set at two attemp- ts), then the device turns off the normal algorithm and a mode alarm will start – a lamp alarm will light constantly which is a signal for the user th...

  • Page 16

    Use and maintenance - - maintenance adjusting the controlling logistical module the logistical module controls the burner. It is secured by a password, so that the currently running program will be safe from undesirable changes. The possible settings of the parameters are as they follow (in the brac...

  • Page 17

    English use and maintenance - - settings of parameters t1, t2, t4, t6 and t7 can be done by the following pattern: - push button sel/ok on the logistical module. - a menu with buttons “arrow up” or “arrow down“ appears and a mode paramet must be chosen. - push button sel/ok. - a menu with the permit...

  • Page 18

    Use and maintenance - 0 - burner maintenance the device for pellets burning in designed in a way that it requires minimal maintenance. The maintenance level directly depends of the quality and the size of the used pellets. Important! Before starting service and maintenance shut down the electricity ...

  • Page 19

    English use and maintenance - 1 - possible troubleshooting attention • all services on the electrical system must be done by a qualified electrical technician who has carefully read the working manual. The device does not work: - check if the pellets quantity is enough (lamp alarm lights); - check i...

  • Page 20

    Bruciatori caldaie murali e terra a gas gruppi termici in ghisa e in acciaio generatori di aria calda trattamento acqua condizionamento lamborghini calor s.P.A. Via statale, 2 00 dosso (ferrara) italia tel. Italia 02/11 - export 02/1 fax italia 02/2 - export 02/ libretto cod. .000.0 (0/0) le illustr...