- DL manuals
- Lamona
- Hob
- LAM1744
- User Manual
Lamona LAM1744 User Manual
Summary of LAM1744
Page 1
User guide ceramic touch control hob lam1744 part no: 083550101 date: 07/02/2017 www.Howdens.Com/appliance-registration.
Page 3: Introduction
Thank you for buying this british-built appliance from us. This user guide book is designed to help you through each step of owning your new product. Please read it carefully before you start using your appliance, as we have endeavored to answer as many questions as possible, and provide you with as...
Page 4: Warning
Warning • if the hob surface is cracked, broken or shattered, switch off the appliance to avoid the possibility of electric shock and call for a service engineer’s visit. • the appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children...
Page 5
Ifyouhaveanelectricalfireinthekitchen: • pull the plug out, or switch off the power at the fuse box - this may be enough to stop the fire imme- diately • smother the fire with a fire blanket, or use a dry powder or carbon dioxide extinguisher • remember: never use water on an electrical or cooking o...
Page 6: Using Your Appliance
Using your appliance getting to know your product note: your appliance layout may differ depending on the model. Hob hob controls 2 3 4 5 1 6 7 cook zone keys individual cook zone displays power down key power up key on/off key minute minder / fault codes keylock 8 cook zone light (x4) 9 timer 10 re...
Page 7: Overview
Overview function description symbol power level once a cook zone is selected, a power level can be set to a low or high temperature. 1-9 residual heat after use, the cooking surface remains hot and the residual heat symbol will be displayed. As it cools, the residual heat symbol will disappear from...
Page 8
Key lock 1 press and hold key lock to deactivate/activate. The red led will be illuminated when active note: if any of the cook zones are on, the key lock function locks all the keys except the on/off key. If the cook zones are off, the key lock function locks all the keys, including the on/off key....
Page 9
Switching on an individual hob cook zone 1 touch and hold the on /off key for 1 second 2 the hob will make a sound and 0 will appear in the cook zone displays 3 touch the required cook zone key, it will start to flash 4 whilst flashing, adjust the power level by using the up or down keys note: you c...
Page 10
Switching off an individual hob cook zone 1 touch the required cook zone key until the zone display flashes 2 return the power level to 0 by pressing the up and down keys together note: you can also touch the down key to until power level 0 appears on the display. Set a time for a cook zone 1 touch ...
Page 11
3 using the up or down keys, set the time required in minutes the cook zone being timed is indicated by flashing led on the timer to check remaining time 1 touch the cook zone symbol for the desired zone 2 touch the the timer symbol to check the remaining time.
Page 12
Adjust the set time 1 touch the cook zone symbol for the desired zone 2 touch the timer symbol 3 using the up or down keys, set the time required in minutes deactivating timed cooking 1 touch the cook zone symbol for the desired zone 2 touch the timer symbol.
Page 13
3 using the down key to return timer to 00 auto heat up 1 select appropriate cook zone 2 press the up key and increase the power level to 9.
Page 14
3 press the plus key again and until the red led is illuminated next to the cook zone. 4 the power level will still be flashing, so now select the power level you would like 5 once set the red led is illuminated. Approx heat up time power level time (min/sec) 1 1:11 2 2:44 3 4:47 4 5:28 5 6:29 6 1:1...
Page 15: Error Codes
Safety shut down if the power level is not changed for a long period of time the cook zone will automatically turn itself off. The maximum time a cook zone can stay on depends on the power level. Power level max time (hours) 1 10 2 5 3 5 4 4 5 3 6 2 7 2 8 2 9 1 error codes hob status codes fault des...
Page 16: Cleaning Your Appliance
Cleaning your appliance do’s note: always switch off your appliance and allow it to cool down before you clean any part of it. Note: please take extra care when cleaning over the symbols on the control panel, as this can lead to them fading. H tips: some foods can mark or damage the metal or paint w...
Page 17: Installation Instructions
Before you start please read the instructions. Planning your installation will save you time and effort. Failure to install appliances correctly is dangerous and could lead to prosecution. Please take care when handling - we recommend the use of protective gloves during installation. Installation sh...
Page 18: Choosing Your Installation
Installation above an oven refer to the manufacturer’s instructions for clearances above the oven. We recommend a minimum 20mm gap between the bottom of the hob and appliance, should the work surface be less than 38mm deep installation above a unit with a drawer or door if necessary, remove the fron...
Page 19: Dimensions And Clearances
Dimensions and clearances worktop cutout sizes hobs - 53mm min hobs - 53mm min x y rear wall please see table below for hob cut out dimensions for your appliance product x(mm) y(mm) *60cm hob 560 490 *77cm hob 737.5 487.5 * the nominal dimensions are shown on the hob cut out table and must be fabric...
Page 20
Cupboard / hood clearances nominal width of the hob 90mm wall unit wall unit 400mm no shelf or overhang of combustible material should be closer than 650mm above the hob. 90mm 400mm min 650mm worktop self adhesive seal apply the self adhesive seal to the underside edges of the hob glass. For best re...
Page 21
Recessed method (selected models) recess the work top to the appropriate depth (approx 5mm) and shape to fit the hob (add 1mm to over- all glass size). Refer to the installation bracket advice to determine your installation type. Insert the hob into the re- cess, ensuring that the foam seal is sitti...
Page 22
Pushfithobinstallation your new hob is pre-fitted with push fit installation clips which are designed to simplify the installation procedure and retain the hob into the worktop. Care must be taken to not damage these clips whilst installing this product. Depending on your product the images below sh...
Page 23
Depending on your product, the images below represents how the system interacts with your worktop. Note; the worktop cut out dimensions are critical and will affect the performance of how the push fit system works. The nominal dimensions are shown on the hob cut out table and must be fabricated to a...
Page 24
This appliance must be earthed. Only connect to the electrical mains terminal with the power switched off. The electrical mains terminal is live. Loose and inappropriate connections can make the terminal overheat. A device must be provided in the electrical installation which allows the appliance to...
Page 25
3 phase supply - for installation in mainland europe for connection to a 3 phase supply, the supplied mains cable and bridging links will need to be removed. • firstly open the terminal block cover using a small flat bladed screwdriver in the door release tabs shown. • remove cable clamp screw and r...
Page 26: Technical Data
Forthespecificpowerratingofyourmodel,refertothedatabadgeontheundersideof your appliance. Electric ceramic hob technical data electrical supply 220~240v 50hz total power rating @ 220 - 240v ~ 50hz (kw) 5.3 kw - 6.3 kw hob details cook zone normal power rating kw @ 240 lh front 2.1 lh rear 1.2 rh rear...
Page 27
Product guarantee details (uk only) your appliance has the benefit of a comprehensive manufacturer’s guarantee which covers the cost of breakdown repairs. (details of which are shown on your proof of purchase document). • any claim during the period of the guarantee must be accompanied by the proof ...
Page 28
Product serial number (place sticker here) issue v2 060217.