- DL manuals
- Lamona
- Hob
- LAM1800
- User manual
Lamona LAM1800 User manual
Summary of LAM1800
Page 1
User guide ceramic touch induction control hob lam1800 part no: 0835502001 date: 07/02/2017 www.Howdens.Com/appliance-registration.
Page 3: Introduction
Thank you for buying this british-built appliance from us. This user guide book is designed to help you through each step of owning your new product. Please read it carefully before you start using your appliance, as we have endeavored to answer as many questions as possible, and provide you with as...
Page 4: Warning
Warning • if the hob surface is cracked, broken or shattered, switch off the appliance to avoid the possibility of electric shock and call for a service engineer’s visit. • the appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children...
Page 5
• fire safety advice if you do have a fire in the kitchen, don’t take any risks - get everyone out of your home and call the fire brigade. If you have an electrical fire in the kitchen: • pull the plug out, or switch off the power at the fuse box - this may be enough to stop the fire imme - diately ...
Page 6: Using Your Appliance
Using your appliance getting to know your product note: your appliance layout may differ depending on the model. Hob control panel 2 3 4 5 1 cook zone keys individual cook zone displays power down key (-) power up key (+) on/off key 6 timer displays 1 2 6 2 2 3 3 4 5 left hand rear right hand rear r...
Page 7: Overview
Overview function description symbol power level once a cook zone is selected, a power level can be set to a low or high temperature. 1-9 residual heat after use, the cooking surface remains hot and the residual heat symbol will be displayed. As it cools, the residual heat symbol will disappear from...
Page 8
Switching the appliance on 1 press on/off key to activate the appliance note: if a cook zone is not selected in 10 seconds, the hob will turn off automatically. Switching the appliance off touch the on/off key for 1 second. A beep sounds and all the heaters will switch off. Switching on an individua...
Page 9
Switching off an individual hob cook zone once the cook zone is selected, touch the down key until “0” appears on the cook zone display. Booster function 1 press the up key until power level “9” appears 2 press the up key again until “p” appears for quick operation, with the cook zone power level “0...
Page 10
3 remove fingers and “l” will appear on all cook zone displays 4 press the on/off key to switch the appliance off 5 press the on/off key to switch the appliance on when you now switch on the hob “ l ” will appear in all the cook zone displays. The child lock feature will be activated until you switc...
Page 11
De-activate child lock 1 press the on/off key to switch the appliance on 2 press and hold the right hand front cook zone and down key 3 remove fingers and touch the down key. The child lock should switch off 4 press the on/off key to switch the appliance on. Child lock is now deactivated. Note: when...
Page 12
Setting the minute minder ensure no cooking zones have been selected. 1 touch and hold the up and down keys together. The display will show “00” 2 press the up or down keys to set the time the maximum time that can be set is 99 minutes. When the time is up, the timer display will flash and a beep wi...
Page 13
3 press the up or down keys to set the time 4 once set, the timed cook zone display will show a dot the timer indicator in the display stops flashing and is not displayed. Operation of a timer is shown by a stationary dot in the cook zone display for the timed cook zone. To check the remaining time,...
Page 14
Pan detection the above “u” symbol appears when a zone has been activated but no pan has been placed on the cook zone. If the “u” symbol does not disappear when a pan is placed on the zone it indicates that the pan is not suitable for induction cooking. When a pan is taken off a zone, the hob automa...
Page 15
Auto stand by the hob will automatically switch off if left (with pan) on for an extended period of time, see maximum running times below. Power level maximum operation time hours 1 8 2 6 3 5 4 5 5 4 6 1.5 7 1.5 8 1.5 9 1.5 p (power boost) 1.5 hob status appliance errors fault description action er0...
Page 16: Cleaning Your Appliance
Cleaning your appliance do’s note: always switch off your appliance and allow it to cool down before you clean any part of it. Note: please take extra care when cleaning over the symbols on the control panel, as this can lead to them fading. H tips: some foods can mark or damage the metal or paint w...
Page 17: Installation Instructions
Before you start please read the instructions. Planning your installation will save you time and effort. Failure to install appliances correctly is dangerous and could lead to prosecution. Please take care when handling - we recommend the use of protective gloves during installation. Installation sh...
Page 18: Choosing Your Installation
Installation above an oven refer to the manufacturer’s instructions for clearances above the oven. We recommend a minimum 20mm gap between the bottom of the hob and appliance, should the work surface be less than 38mm deep installation above a unit with a drawer or door if necessary, remove the fron...
Page 19: Dimensions And Clearances
Dimensions and clearances worktop cutout sizes hobs - 53mm min hobs - 53mm min x y rear wall please see table below for hob cut out dimensions for your appliance product x(mm) y(mm) *60cm hob 560 490 *77cm hob 737.5 487.5 * the nominal dimensions are shown on the hob cut out table and must be fabric...
Page 20
Cupboard / hood clearances nominal width of the hob 90mm wall unit wall unit 400mm no shelf or overhang of combustible material should be closer than 650mm above the hob. 90mm 400mm min 650mm worktop self adhesive seal apply the self adhesive seal to the underside edges of the hob glass. For best re...
Page 21
Recessed method (selected models) recess the work top to the appropriate depth (approx 5mm) and shape to fit the hob (add 1mm to over - all glass size). Refer to the installation bracket advice to determine your installation type. Insert the hob into the re- cess, ensuring that the foam seal is sitt...
Page 22
Push fit hob installation your new hob is pre-fitted with push fit installation clips which are designed to simplify the installation procedure and retain the hob into the worktop. Care must be taken to not damage these clips whilst installing this product. Depending on your product the images below...
Page 23
Depending on your product, the images below represents how the system interacts with your worktop. Note; the worktop cut out dimensions are critical and will affect the performance of how the push fit system works. The nominal dimensions are shown on the hob cut out table and must be fabricated to a...
Page 24
This appliance must be earthed. Only connect to the electrical mains terminal with the power switched off. The electrical mains terminal is live. Loose and inappropriate connections can make the terminal overheat. A device must be provided in the electrical installation which allows the appliance to...
Page 25
3 phase supply - for installation in mainland europe for connection to a 3 phase supply, the supplied mains cable and bridging link will need to be removed. • firstly open the terminal block cover using a small flat bladed screwdriver • remove cable clamp screw and remove mains cable • remove 1 brid...
Page 26: Technical Data
Individual cook zone power ratings cook zone hob size (cm) normal power rating (kw) boost power rating (kw) left hand front 60 1.85 2.10 left hand rear 1.40 n/a right hand front 1.40 n/a right hand rear 1.85 2.10 induction hob technical data max. Total power rating hob size (cm) 60 220 - 240v ~ 50hz...
Page 27
Product guarantee details (uk only) your appliance has the benefit of a comprehensive manufacturer’s guarantee which covers the cost of breakdown repairs. (details of which are shown on your proof of purchase document). • any claim during the period of the guarantee must be accompanied by the proof ...
Page 28
Product serial number (place sticker here) issue v2 070217.