P p p r r r o o o l l l u u u m m m d d d 3 3 3 – – – 2 2 2 5 5 5 0 0 0 w w w c c c y y y m m m c c c o o o l l l o o o u u u r r r c c c h h h a a a n n n g g g e e e r r r user’ s manual release 1.0 this manual must be considered an integral part of the projector..
1 before connecting and using the projector, it is important to read carefully all the instructions in this manual. Qualified personnel only, in compliance with all the security laws, can do the installation, the maintenance and the utilisation of this projector. Before connecting the projector, mak...
2 dimensions & weight weight: 10 kg weight: 10 kg technical data - aluminium body - silent small fan - brackets for adjustable fixing - msd 250w (base gy9.5) lamp - magnetic ballast with power factor correction (1.8a max @ 230vac with lamp on) - colour changing system c.M.Y. (unlimited colours combi...
3 storage the projector, in its original packing, must be kept in covered, dry areas with a temperature between –10°c and +50°c. Attention, the projector will be damaged during the unpacking. Admissible environmental conditions the projector was engineered and produced to function in indoor areas wi...
4 example of connection example 1 : the dmx signal is generated by a dmx controller, the signal cable goes in and out from each projector up to the last one. The projectors will execute the same scenes if the dmx addresses are the same (factory set is 1) or they can be driven one by one if the dmx a...
5 standard dmx controllers have only one signal out-put. If more than 32 projectors are used it is necessary to have a signal splitter, that will duplicate the signal in 2 or more lines. If the signal cable is very long, it is necessary to install a signal amplifier on the dmx line (at least every 3...
6 dmx512 specifications the projector reads 6 consecutive dmx dmx ch. Function channels starting from the set address. 1 dimmer 2 shutter/strobe the aux channel always works as rainbow 3 cyan control channel and if remote control 4 magenta is active (index 5) also it works as remote 5 yellow control...
7 (ch. 3) cyan select the quantity of the cyan colour proportionally to the value of the dmx channel. “0” = no colour, “255” = full colour (ch. 4) magenta select the quantity of the magenta colour proportionally to the value of the dmx channel. “0” = no colour, “255” = full colour (ch. 5) yellow sel...
8 user’s interface press and release the push-button mode to access the different functions, as indicated by the three led index (green led on): see the table in the next page for the meaning. Use the + or - button to select the number of the index . Parameter (yellow led on): use the + or - button ...
9 parameters the parameters boolean type (min=0, max=1) enable the controlled function when their value is = 1 and they unable it when their value is = 0. Index name effect min default max 0 dmx index sets the dmx address of the projector 1 1 507 2 shut on colour closes the shutter before to change ...
10 stand alone mode (recordable dmx scenes) to start this execution, assign to index n° 10 (program execution) the value from 1 to 20 . It is possible to create an inside program that allows the projector to function on "stand-alone" mode, it is necessary to have a dmx controller to record the scene...
11 remote control of parameters if the remote enable parameter (index n°5) is equal to 1, then it is possible to modify or activate some functions of the projector, via dmx. The activation of controls is based on a precise time sequence of the dmx channels values, if a step of the sequence is wrong,...
12 lamp replacement 1) disconnect the projector from the main power supply 2) unscrew the 4 screws “d” that hold the lamp holder 3) remove the lamp holder 4) remove the lamp, taking care to wear proper protective gloves 5) insert a new lamp 6) re-insert the lamp holder 7) fix well the 4 screws that ...
