Lance Truck Camper Owner's Manual - page 81
81
73
NOTE:
Never use abrasive, caustic cleaners, alcohol or
solvents as they can cause permanent damage to the
finish.
DO NOT USE WINDEX as it will damage the acrylic.
Never use any petroleum based cleaners, or caustic
chemicals on your windows.
DO NOT USE WD-40 (as it is petroleum based).
Never use a razor blade, putty knife or abrasive pad to
clean your windows.
Do not use a high pressure spray nozzle when rinsing
your windows after washing.
Avoid washing windows in direct sunlight.
JACK BRACKETS
The corner jack brackets need to be inspected each
time the camper is to be loaded or removed from the
truck. These brackets can loosen and the seals
separate during regular use due to rocking, while
loading or unloading or while the camper is being
stored. Retighten the bolts until they are snug and
reseal the brackets as needed. Do not over-tighten as
this can cause the fasteners to strip-out.
CAMPER JACKS
The internal parts of the jacks are permanently
lubricated at the factory and do not require any further
lubrication. At least once each camping season fully
extend the jacks and clean dirt and grime from outside
of the inner tube. Coat the entire outside of the tube
with silicone spray lubricant. This will protect the finish
of the inner tube and provide lubrication between the
jack’s tubes. Clean dirt and automotive polish or wax
to the outer tube of the jacks to maintain the
appearance.
AIR CONDITIONER
The air conditioner mounting bolts should be checked
for tightness after the first 500 miles. Removing the
interior shroud and inspecting the four (4) bolts located
in the corners of the roof opening accomplishes this.
Aside from securing the air conditioner to the roof,
these fasteners apply pressure to the sealing gasket
between the air conditioner and the top of the roof.
Loose fasteners could cause water intrusion around
the roof opening.
TURNBUCKLES
Each time the turnbuckles are installed, and any time
they begin to squeak, place a few drops of oil into the
turnbuckle barrel at the captive hook end. This will
reduce squeaking caused when the turnbuckles dry
out.
It is important that the turnbuckles be kept clean and
protected from corrosive agents, such as salt spray,
acid rain, etc. This is best done by cleaning and
waxing the turnbuckles with a good automotive wax or
chrome polish.
OVERHEAD VENTS
The vents can be cleaned from the top of the camper.
Use soapy water on the vent cover. The screens may
be vacuumed or lightly brushed to remove
accumulation of leaves or other debris. Lubricate the
gears and mechanism yearly with a light, water
resistant grease.
SKYLIGHT
The skylight should be cleaned at least once a year.
Rinse the skylight with lukewarm water. Wash with
mild soap and lukewarm water using a soft cloth or
sponge and gently wash to loosen dirt and grime. DO
NOT SCRUB or use brushes or squeegees. Repeat
rinse and dry with a soft cloth to prevent water spotting.
EXTERIOR LIGHTS
Check the operation of your camper’s exterior lights
prior to each trip. This also includes your truck’s
lighting. A burned out bulb can create an unsafe
condition by reducing your ability to signal your
intentions to other drivers. When replacing exterior
bulbs, take care that the sealant around the light
fixture is not disturbed. This can cause a potential
water leak. Refer to the bulb replacement chart for the
proper replacement bulbs.
WIRING
Make sure the connector-plug prongs and receptacles
are clean. Lightly coat all electrical terminal
connections with non-conducting (dielectric), light
waterproof grease. Clean the prongs with very fine
sandpaper, being careful not to damage the contact
area.
USE AND CARE OF THE TENT
Preventing Mildew
One of the easiest ways to damage your tent is by not
drying it as quickly as possible when it gets wet.
Storing a wet tent for as little as 24 hours in warm
weather is likely to start the process of mildew forming
on the fabric. Mildew can permanently damage the
waterproof coatings by causing them to separate from
the fabric, but mild to severe staining is more common.
Mildew stains are permanent. They cannot be
removed without potential harm to the fabric coatings,
and they are not covered by warranty. Even when your
tent appears to be dry after use, it is always best to
unfold at home and make sure it is completely dry
before storing. Periodically open and air out your tent
to prevent odor buildup and fabric deterioration.
DO NOT USE WINDEX as it will damage the acrylic.
Never use any petroleum based cleaners, or caustic
chemicals on your windows/skylight vent.
DO NOT USE WD-40 (as it is petroleum based).
Never use a razor blade, putty knife or abrasive pad to
clean your windows/skylight vent.
Do not use a high pressure spray nozzle when rinsing
your windows/skylight vent after washing.
Avoid washing windows/skylight vent in direct sunlight.
73
WARNING:
Never use abrasive, caustic cleaners, alcohol or
solvents as they can cause permanent damage to the
finish.
DO NOT USE WINDEX as it will damage the acrylic.
Never use any petroleum based cleaners, or caustic
chemicals on your windows.
DO NOT USE WD-40 (as it is petroleum based).
Never use a razor blade, putty knife or abrasive pad to
clean your windows.
Do not use a high pressure spray nozzle when rinsing
your windows after washing.
Avoid washing windows in direct sunlight.
JACK BRACKETS
The corner jack brackets need to be inspected each
time the camper is to be loaded or removed from the
truck. These brackets can loosen and the seals
separate during regular use due to rocking, while
loading or unloading or while the camper is being
stored. Retighten the bolts until they are snug and
reseal the brackets as needed. Do not over-tighten as
this can cause the fasteners to strip-out.
CAMPER JACKS
The internal parts of the jacks are permanently
lubricated at the factory and do not require any further
lubrication. At least once each camping season fully
extend the jacks and clean dirt and grime from outside
of the inner tube. Coat the entire outside of the tube
with silicone spray lubricant. This will protect the finish
of the inner tube and provide lubrication between the
jack’s tubes. Clean dirt and automotive polish or wax
to the outer tube of the jacks to maintain the
appearance.
AIR CONDITIONER
The air conditioner mounting bolts should be checked
for tightness after the first 500 miles. Removing the
interior shroud and inspecting the four (4) bolts located
in the corners of the roof opening accomplishes this.
Aside from securing the air conditioner to the roof,
these fasteners apply pressure to the sealing gasket
between the air conditioner and the top of the roof.
Loose fasteners could cause water intrusion around
the roof opening.
TURNBUCKLES
Each time the turnbuckles are installed, and any time
they begin to squeak, place a few drops of oil into the
turnbuckle barrel at the captive hook end. This will
reduce squeaking caused when the turnbuckles dry
out.
It is important that the turnbuckles be kept clean and
protected from corrosive agents, such as salt spray,
acid rain, etc. This is best done by cleaning and
waxing the turnbuckles with a good automotive wax or
chrome polish.
OVERHEAD VENTS
The vents can be cleaned from the top of the camper.
Use soapy water on the vent cover. The screens may
be vacuumed or lightly brushed to remove
accumulation of leaves or other debris. Lubricate the
gears and mechanism yearly with a light, water
resistant grease.
SKYLIGHT
The skylight should be cleaned at least once a year.
Rinse the skylight with lukewarm water. Wash with
mild soap and lukewarm water using a soft cloth or
sponge and gently wash to loosen dirt and grime. DO
NOT SCRUB or use brushes or squeegees. Repeat
rinse and dry with a soft cloth to prevent water spotting.
EXTERIOR LIGHTS
Check the operation of your camper’s exterior lights
prior to each trip. This also includes your truck’s
lighting. A burned out bulb can create an unsafe
condition by reducing your ability to signal your
intentions to other drivers. When replacing exterior
bulbs, take care that the sealant around the light
fixture is not disturbed. This can cause a potential
water leak. Refer to the bulb replacement chart for the
proper replacement bulbs.
WIRING
Make sure the connector-plug prongs and receptacles
are clean. Lightly coat all electrical terminal
connections with non-conducting (dielectric), light
waterproof grease. Clean the prongs with very fine
sandpaper, being careful not to damage the contact
area.
USE AND CARE OF THE TENT
Preventing Mildew
One of the easiest ways to damage your tent is by not
drying it as quickly as possible when it gets wet.
Storing a wet tent for as little as 24 hours in warm
weather is likely to start the process of mildew forming
on the fabric. Mildew can permanently damage the
waterproof coatings by causing them to separate from
the fabric, but mild to severe staining is more common.
Mildew stains are permanent. They cannot be
removed without potential harm to the fabric coatings,
and they are not covered by warranty. Even when your
tent appears to be dry after use, it is always best to
unfold at home and make sure it is completely dry
before storing. Periodically open and air out your tent
to prevent odor buildup and fabric deterioration.
TURNBUCKLES
Each time the turnbuckles are installed, and any time
theybegintosqueak,placeafewdropsofoilintothe
turnbuckle barrel at the captive hook end. This will reduce
squeakingcausedwhentheturnbucklesdryout.
It is important that the turnbuckles be kept clean and
protected from corrosive agents, such as salt spray, acid
rain, etc. This is best done by cleaning and waxing the
turnbuckles with a good automotive wax or chrome
polish.
73
WARNING:
Never use abrasive, caustic cleaners, alcohol or
solvents as they can cause permanent damage to the
finish.
DO NOT USE WINDEX as it will damage the acrylic.
Never use any petroleum based cleaners, or caustic
chemicals on your windows.
DO NOT USE WD-40 (as it is petroleum based).
Never use a razor blade, putty knife or abrasive pad to
clean your windows.
Do not use a high pressure spray nozzle when rinsing
your windows after washing.
Avoid washing windows in direct sunlight.
JACK BRACKETS
The corner jack brackets need to be inspected each
time the camper is to be loaded or removed from the
truck. These brackets can loosen and the seals
separate during regular use due to rocking, while
loading or unloading or while the camper is being
stored. Retighten the bolts until they are snug and
reseal the brackets as needed. Do not over-tighten as
this can cause the fasteners to strip-out.
CAMPER JACKS
The internal parts of the jacks are permanently
lubricated at the factory and do not require any further
lubrication. At least once each camping season fully
extend the jacks and clean dirt and grime from outside
of the inner tube. Coat the entire outside of the tube
with silicone spray lubricant. This will protect the finish
of the inner tube and provide lubrication between the
jack’s tubes. Clean dirt and automotive polish or wax
to the outer tube of the jacks to maintain the
appearance.
AIR CONDITIONER
The air conditioner mounting bolts should be checked
for tightness after the first 500 miles. Removing the
interior shroud and inspecting the four (4) bolts located
in the corners of the roof opening accomplishes this.
Aside from securing the air conditioner to the roof,
these fasteners apply pressure to the sealing gasket
between the air conditioner and the top of the roof.
Loose fasteners could cause water intrusion around
the roof opening.
TURNBUCKLES
Each time the turnbuckles are installed, and any time
they begin to squeak, place a few drops of oil into the
turnbuckle barrel at the captive hook end. This will
reduce squeaking caused when the turnbuckles dry
out.
It is important that the turnbuckles be kept clean and
protected from corrosive agents, such as salt spray,
acid rain, etc. This is best done by cleaning and
waxing the turnbuckles with a good automotive wax or
chrome polish.
OVERHEAD VENTS
The vents can be cleaned from the top of the camper.
Use soapy water on the vent cover. The screens may
be vacuumed or lightly brushed to remove
accumulation of leaves or other debris. Lubricate the
gears and mechanism yearly with a light, water
resistant grease.
SKYLIGHT
The skylight should be cleaned at least once a year.
Rinse the skylight with lukewarm water. Wash with
mild soap and lukewarm water using a soft cloth or
sponge and gently wash to loosen dirt and grime. DO
NOT SCRUB or use brushes or squeegees. Repeat
rinse and dry with a soft cloth to prevent water spotting.
EXTERIOR LIGHTS
Check the operation of your camper’s exterior lights
prior to each trip. This also includes your truck’s
lighting. A burned out bulb can create an unsafe
condition by reducing your ability to signal your
intentions to other drivers. When replacing exterior
bulbs, take care that the sealant around the light
fixture is not disturbed. This can cause a potential
water leak. Refer to the bulb replacement chart for the
proper replacement bulbs.
WIRING
Make sure the connector-plug prongs and receptacles
are clean. Lightly coat all electrical terminal
connections with non-conducting (dielectric), light
waterproof grease. Clean the prongs with very fine
sandpaper, being careful not to damage the contact
area.
USE AND CARE OF THE TENT
Preventing Mildew
One of the easiest ways to damage your tent is by not
drying it as quickly as possible when it gets wet.
Storing a wet tent for as little as 24 hours in warm
weather is likely to start the process of mildew forming
on the fabric. Mildew can permanently damage the
waterproof coatings by causing them to separate from
the fabric, but mild to severe staining is more common.
Mildew stains are permanent. They cannot be
removed without potential harm to the fabric coatings,
and they are not covered by warranty. Even when your
tent appears to be dry after use, it is always best to
unfold at home and make sure it is completely dry
before storing. Periodically open and air out your tent
to prevent odor buildup and fabric deterioration.
CAMPER JACKS
The internal parts of the jacks are permanently lubricated
atthefactoryanddonotrequireanyfurtherlubrication.
At least once each camping season fully extend the jacks
and clean dirt and grime from outside of the inner tube.
Coat the entire outside of the tube with silicone spray
lubricant. This will protect the finish of the inner tube and
provide lubrication between the jack’s tubes. Clean dirt
and apply automotive polish or wax to the outer tube of
the jacks to maintain the appearance.
SKYLIGHTS
The skylights should be cleaned at least once a year.
Rinse the skylights with lukewarm water. Wash with mild
soap and lukewarm water using a soft cloth or sponge
and gently wash to loosen dirt and grime. DO NOT
SCRUBorusebrushesorsqueegees.Repeatrinseand
dry with a soft cloth to prevent water spotting.
EXTERIOR LIGHTS
Check the operation of your camper’s exterior lights prior
to each trip. This should also include your truck’s lighting.
An inoperative bulb or fixture can create an unsafe condi-
tion by reducing your ability to signal your intentions to
other drivers. When replacing exterior bulbs, take care that
the sealant around the light is not disturbed. When replac-
ing exterior LED fixtures, ensure the new fixture is installed
using a recommended sealant. Your Lance Dealer can
assist you with replacement of the fixture and/or provide
information on the appropriate sealants if you prefer to do
this work yourself.
73
WARNING:
Never use abrasive, caustic cleaners, alcohol or
solvents as they can cause permanent damage to the
finish.
DO NOT USE WINDEX as it will damage the acrylic.
Never use any petroleum based cleaners, or caustic
chemicals on your windows.
DO NOT USE WD-40 (as it is petroleum based).
Never use a razor blade, putty knife or abrasive pad to
clean your windows.
Do not use a high pressure spray nozzle when rinsing
your windows after washing.
Avoid washing windows in direct sunlight.
JACK BRACKETS
The corner jack brackets need to be inspected each
time the camper is to be loaded or removed from the
truck. These brackets can loosen and the seals
separate during regular use due to rocking, while
loading or unloading or while the camper is being
stored. Retighten the bolts until they are snug and
reseal the brackets as needed. Do not over-tighten as
this can cause the fasteners to strip-out.
CAMPER JACKS
The internal parts of the jacks are permanently
lubricated at the factory and do not require any further
lubrication. At least once each camping season fully
extend the jacks and clean dirt and grime from outside
of the inner tube. Coat the entire outside of the tube
with silicone spray lubricant. This will protect the finish
of the inner tube and provide lubrication between the
jack’s tubes. Clean dirt and automotive polish or wax
to the outer tube of the jacks to maintain the
appearance.
AIR CONDITIONER
The air conditioner mounting bolts should be checked
for tightness after the first 500 miles. Removing the
interior shroud and inspecting the four (4) bolts located
in the corners of the roof opening accomplishes this.
Aside from securing the air conditioner to the roof,
these fasteners apply pressure to the sealing gasket
between the air conditioner and the top of the roof.
Loose fasteners could cause water intrusion around
the roof opening.
TURNBUCKLES
Each time the turnbuckles are installed, and any time
they begin to squeak, place a few drops of oil into the
turnbuckle barrel at the captive hook end. This will
reduce squeaking caused when the turnbuckles dry
out.
It is important that the turnbuckles be kept clean and
protected from corrosive agents, such as salt spray,
acid rain, etc. This is best done by cleaning and
waxing the turnbuckles with a good automotive wax or
chrome polish.
OVERHEAD VENTS
The vents can be cleaned from the top of the camper.
Use soapy water on the vent cover. The screens may
be vacuumed or lightly brushed to remove
accumulation of leaves or other debris. Lubricate the
gears and mechanism yearly with a light, water
resistant grease.
SKYLIGHT
The skylight should be cleaned at least once a year.
Rinse the skylight with lukewarm water. Wash with
mild soap and lukewarm water using a soft cloth or
sponge and gently wash to loosen dirt and grime. DO
NOT SCRUB or use brushes or squeegees. Repeat
rinse and dry with a soft cloth to prevent water spotting.
EXTERIOR LIGHTS
Check the operation of your camper’s exterior lights
prior to each trip. This also includes your truck’s
lighting. A burned out bulb can create an unsafe
condition by reducing your ability to signal your
intentions to other drivers. When replacing exterior
bulbs, take care that the sealant around the light
fixture is not disturbed. This can cause a potential
water leak. Refer to the bulb replacement chart for the
proper replacement bulbs.
WIRING
Make sure the connector-plug prongs and receptacles
are clean. Lightly coat all electrical terminal
connections with non-conducting (dielectric), light
waterproof grease. Clean the prongs with very fine
sandpaper, being careful not to damage the contact
area.
USE AND CARE OF THE TENT
Preventing Mildew
One of the easiest ways to damage your tent is by not
drying it as quickly as possible when it gets wet.
Storing a wet tent for as little as 24 hours in warm
weather is likely to start the process of mildew forming
on the fabric. Mildew can permanently damage the
waterproof coatings by causing them to separate from
the fabric, but mild to severe staining is more common.
Mildew stains are permanent. They cannot be
removed without potential harm to the fabric coatings,
and they are not covered by warranty. Even when your
tent appears to be dry after use, it is always best to
unfold at home and make sure it is completely dry
before storing. Periodically open and air out your tent
to prevent odor buildup and fabric deterioration.
BATTERY(S)
Your camper is outfitted with a battery(s) that oper-
ates lighting, jacks, slide-outs or other accessories. The
battery(s) may be kept charged either by the truck, by the
generator or shore power.
A disconnect switch is provided to disconnect the
battery(s) when you do not plan to be using the camper
for an extended period, such as seasonal storage.
The battery must be kept in a charged condition during
storage. The battery could freeze and break if it becomes
discharged.