1. DL manuals
  2. Land Pride
  3. Lawn Mower
  4. FD2548
  5. Operator's Manual

Land Pride FD2548 Operator's Manual

Manual is about: 2-Spindle Grooming Mower

Summary of FD2548

  • Page 1

    1/29/04 0 fd2548 2-spindle grooming mower 10817 310-156m operator’s manual 1/29/04 cover photo may show optional equipment not supplied with standard unit. © copyright 2004 printed read the operator’s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - f...

  • Page 2

    1/29/04 1 this manual has been prepared to instruct you in the safe and efficient operation of your 25 series grooming mower. Read and follow all instructions and safety pre- cautions carefully. The parts on your 25 series grooming mower have been specially designed and should only be replaced with ...

  • Page 3

    1/29/04 2 safety rules most accidents are the result of negligence and carelessness, usually caused by failure of the operator to follow simple but necessary safety precautions. The following safety precautions are suggested to help prevent such accidents. The safe operation of any machinery is a bi...

  • Page 4: Operate Only With

    1/29/04 3 safety rules (con’t.) safety decals --important-- * your grooming mower comes equipped with all safety decals in place. * always keep safety decals clean and legible. * replace all damaged or missing safety decals. To order new safety decals go to your land pride dealer and reference part ...

  • Page 5: Caution!

    1/29/04 4 nut & bolt torquing chart this chart is based on torque requirements in foot pounds for grade 5 bolts. Bolt diameter minimum torque maximum torque bolt diameter minimum torque maximum torque 1/4" 9 11 3/4" 270 324 5/16" 17 20 7/8" 400 480 3/8" 35 42 1" 580 696 7/16" 54 64 1 1/8" 800 880 1/...

  • Page 6: Caution!

    1/29/04 5 1. Be certain that tractor draw bar will not interfere. Move draw bar ahead or remove if required. Draw bar should also be checked for clearance when unit is being raised for the first time. 2. Align lower link arms of tractor to hitch clevises on mower. Insert lower hitch pins into lower ...

  • Page 7

    1/29/04 6 leveling the mower three and four gauge wheels front to rear: note: tractor and mower should be on level ground. 1. Set the lower hitches and upper floating hitch as shown in fig. 1 on page 5. 2. Start tractor and raise mower, watching that tractor draw bar (if not removed) does not interf...

  • Page 8: Caution!

    1/29/04 7 1. Using the tractor, raise the mower off the ground and support under it with secure blocking so not to let the mower drift down during maintenance. 2. Holding wheel and yoke assembly up, remove quick- lock pin from top of gauge wheel spindle. Position full length spacers and half spacer ...

  • Page 9

    1/29/04 8 operating instructions before beginning to mow, the following inspection should be performed: proper servicing and adjustments is the key to the long life of any machine. With careful and systematic inspec- tion of the mower, you can avoid costly maintenance, time and repair. For safety re...

  • Page 10: Caution!

    1/29/04 9 v-belt installation - 1. Remove belt covers. 2. Move belt take-up handle in a clockwise direction to relieve tension on belt. 3. With tension relieved from belt remove old belt from pulleys. 4. Install new belt referring to the figure below (also re- fer to the decal on top of mower deck)....

  • Page 11

    1/29/04 10 at the end of the working season or when the mower will not be used for a long period, it is good practice to clean off any dirt or grease that may have accumulated. Check the blades for wear and replace if necessary. See "maintenance" on page 9. Inspect the mower for loose, damaged or wo...

  • Page 12

    1/29/04 11 options (con’t.) mower chain kit assembly instructions remove tractor 3-point hitch upper link pin (#1). Install lift chains (#2) on outside surface of upper link mounting plate on tractor. Reinstall link pin and keeper. Note: depending upon brand of tractor the link pin may need to be re...

  • Page 13: Caution!

    1/29/04 12 problem cause solution 1. Discharge chute plugged belt not installed correctly check installation of belt grass too wet wait until grass dries grass too tall raise cutting height of mower and cut grass twice rpm of tractor too low mow at full throttle (540 pto rpm) check pto speed & tract...

  • Page 14

    1/29/04 13 warranty land pride warrants to the original purchaser of new land pride products, that they are free of defects in material and workmanship. This warranty is applicable only for the normal life expectancy of the unit or individual components for a period of one year from date of original...

  • Page 15

    1/29/04 14 flat deck mower - deck & components 10467.

  • Page 16

    1/29/04 15 flat deck mower - deck & components (con’t.) ref. Part no. Description 1. 310-046h 48" mower deck 2. 310-071h lower hitch lug 3. 310-020s lower hitch pin 4. 805-141c pin, lock 5/8" x 2" long {2 wheel units only} 5. 805-140c pin, pivot 3/4" x 2" long 6. 805-143c pin, hair cotter 0.120 7. 8...

  • Page 17

    1/29/04 16 flat deck mower belt drive 18642.

  • Page 18

    1/29/04 17 flat deck mower belt drive (con’t.) ref. Part no. Description 1. 826-011c gearbox - comer 826-081c gearbox - ieg 2. 802-207c bolt 5/8"-18 x 1 1/2" long 3. 804-022c washer, lock 5/8" 4. 803-022c nut 5/8"-18 5. 817-050c shaft protector 6. 310-331d key 1/4" x 11/16" long 7. 310-041d gear box...

  • Page 19

    1/29/04 18 comer gearbox (part no. 826-011c) 10508.

  • Page 20

    1/29/04 19 comer gearbox (con’t.) (part no. 826-011c) ref. Part no. Description 1. 0.141.0330.00 casting - machined 2. 8.4.1.00889 key, parallel b 10 x 8 x 30 3. 8.0.1.00870 bearing 6207 4. 8.7.0.00693 cap 5. 0.141.2100.00 shaft 1 3/8" 6. 0.141.5000.00 gear 7. 0.141.7100.00 spacer 8. 8.5.2.00131 rin...

  • Page 21

    1/29/04 20 ieg gearbox (part no. 826-081c) 10891.

  • Page 22

    1/29/04 21 ieg gearbox (con’t.) (part no. 826-081c) ref. Part no. Description 1. 18-021 housing 2. 04-004 ball bearing #207 3. 09-002 plug, pipe 1/2"-14 4. 02-035 input shaft 5. 21-012 retaining ring 6. 03-036 input gear 30 tooth 7. 08-004a gasket, input cap 0.25 mm 8. 08-004b gasket, input cap 0.10...

  • Page 23

    1/29/04 22 gauge wheel assembly 18643.

  • Page 24

    1/29/04 23 gauge wheel assembly (con’t.) ref. Part no. Description 1. 310-014h gauge wheel arm weldment 2. 827-002c spacer 1" 3. 817-048c bushing, spindle 4. 827-001c spacer 1/2" 5. 805-065c pin, wire retaining 1/4" x 1 3/4" long 6. 310-149h yoke, gauge wheel {used on mowers after serial #59102} 310...

  • Page 25

    1/29/04 24 power take-off (part no. 826-012c) ref. Part no. Description 1. 380905 end yoke 2. 381908 quick disconnect yoke 3. 044439 cross & bearing kit 4. 041065 inboard yoke 5. 020614 spring pin 6. 054484 inner profile 7. 377234 shield cone - 4 rib 8. 087279 bearing ring 9. 387332 outer shield tub...

  • Page 26

    1/29/04 25 options front anti-scalping roller (part no. 310-077s) ref. Part no. Description 1. 817-049c 4" x 10" roller 2. 310-076h left hand mount bracket 3. 310-190d right hand mount bracket 4. 803-114c nut, lock 3/4"-16 nylock collar 5. 801-043c screw, pan head 3/8"-16 x 1" long 6. 804-013c washe...

  • Page 27

    1/29/04 26 options chain kit (part no. 310-038s) ref. Part no. Description 1. 310-117d chain bracket - lower 2. 310-032h lift chain 3. 817-057c cap plug.

  • Page 28

    1/29/04 27 decal placement ref. Part no. Description 310-086a fd/at safety decal package complete safety decal package 310-079a fd/at2548 decal package complete decal package 1. 818-165c lp logo small buckskin 2. 818-552c decal danger pto driveline 3. 818-139c decal pto fd/at {826-012c} 4. 818-540c ...

  • Page 29

    1/29/04 28 notes.

  • Page 30

    Corporate office: p.O. Box 5060 salina, kansas 67402-5060 usa www.Landpride.Com.