Land Pride ZXT54 Pro Assembly Instructions
1
© Copyright 2008
Printed
Before You Start
Your Roll Over Protective Structure is exclusively
designed for your Land Pride ZXT mower. Please read
these installation instructions and your ZXT mower
Operator’s Manual thoroughly before beginning.
Especially read information relating to safety concerns.
Also included in the Operator’s Manual is important
information on operation, adjustment, troubleshooting,
and maintenance for this attachment (some manual
sections do not apply to all accessories).
A separate Parts Manual for the Zero Turn Mower is
available free of charge at www.landpride.com or can be
purchased from your nearest Land Pride dealer. Have
the model and serial number of your Zero Turn Mower
handy when placing an order.
Manual Part Numbers:
• Operator’s Manual . . . . . . . . . . . . . . . . . 357-271M
• Parts Manual . . . . . . . . . . . . . . . . . . . . . 357-271P
General Information
These assembly instructions apply to the following
Accessory kits listed below:
357-273A
Folding ROPS W/Seat Belt, ZXT Series
Tools required:
•
Safety Glasses
•
Work Gloves
•
11/16" box end or open end wrench
•
3/4" box end or open end wrench
•
Torque wrench with 11/16" & 3/4" sockets
Assembly Instructions
!
WARNING
Do not modify the Roll Over Protective Structure in any way.
This Roll Over Protective Structure has been designed
specifically for this machine and any modifications can affect
its performance in the event of a roll over.
When you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
!
IMPORTANT: Before you begin, read these
instructions and check to be sure all parts and tools
are accounted for. Please retain these installation
instructions for future reference and parts ordering
information.
A detailed listing of parts for this accessory kit is
provided on page 2. Use the list as a checklist to
inventory parts received. Please contact your local
Land Pride dealer for any missing hardware.
Initial Preparations
1.
Park unit on a flat level surface. Make sure blade
engagement switch is (OFF), both control levers are
fully (OUT), park brake is (ON) and switch key is
turned (OFF) and removed.
Seat Belt Assembly (Deluxe Seat Shown)
Suspension Seat Also Includes Seat Belt Mounts (B & C)
Figure 1
Seat Belt Assembly
Refer to Figure 1
1.
Insert seat belt clip (#4) with push button "A" into clip
sleeve (#5).
2.
Make sure push button “A” is facing out as shown.
Insert 7/16" bolt (#1A) through flat washer (#3), seat
belt clip & sleeve (#4 & #5), mounting hole “B” and
flat washer (#3). Secure bolt with nylock nut (#2).
Rotate seat belt up to the approximate angle shown
and tighten nylock nut to 36 ft-lbs. of torque.
3.
Orient seat belt retractor (#6) with spring retractor
facing out as shown. Insert 7/16" bolt (#1B) through
flat washer (#3), mounting hole “C”, seat belt
retractor (#6) and flat washer (#3). Secure bolt with
nylock nut (#2). Rotate seat belt retractor to the
approximate angle shown and tighten nylock nut to
36 ft-lbs. of torque.
IMPORTANT: Your ZXT mower seat must have seat
belt mounting holes in the back rest side plates. See
Figure 1, balloon (B). If it does not, you will need to
replace your seat with one that does.
30213
Seat Belt Retractor (#6) Must Be Mounted This
Side Of Mounting Hole “C” To Keep Retractor
From Interfering With Right Side Fuel Tank.
Spring Retractor
ZXT54 Pro & ZXT60 Pro Zero Turn Mowers
ZXT Roll Over Protective Structure
Assembly Instructions
4/19/10
Manual No. 357-274M