Summary of GH100R
Page 1
Gh50r gh100r gh50r-212.
Page 2
2 dear player, thank you very much for purchasing your new laney product and becoming part of the worldwide laney family. Each and every laney unit is designed and built with the utmost attention to care and detail, so i trust yours will give you many years of enjoyment. Laney products have a herita...
Page 3
Introduction 3 gh50r-212 gh100r gh50r the infinite balance of power the ghr range represents the most tonally versatile amplifiers we have ever heard. Unique construction allows direct control by the player over the balance between the amount of pre amp and power amp colour in the overall tone. A ba...
Page 4
4 warning: when using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions safe. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do ...
Page 5
Note this manual has been written for easy access of information. The front and rear panels are graphically illustrated, with each control and feature numbered. For a description of the function of each control feature, simply check the number with the explanations adjacent to each panel. Your laney...
Page 6
Front panel controls 6 gh50r-212 gh50r, gh100r 1. Input: 1/4" mono jack socket. Connect your guitar here. Use only a good quality instrument cable. 2. Channel 1 drive: – this control determines the level of drive present in the channel 1 signal. This control should be set in conjunction with the lev...
Page 7
Front panel controls continued 7 5. Channel 2 volume: – the volume control lets you determine the amount of signal that progresses through to the power amp section. The volume control should be used in conjunction with the channel 2 drive control and the master output control in order to get the des...
Page 8
Rear panel controls 8 gh50r-212 gh50r, gh100r l z b 1 2 3 4 l z b 1 2 3 4 1. Mains inlet socket: connect to your power source. Make sure the voltage indicated on the rear panel is correct for – your country! Mains fuse: this drawer contains the main safety fuse for the unit. The fuse protects the am...
Page 9
Rear panel controls continued 9 4.Auxiliary input: this input allows the connection of backing tracks etc. To be mixed in post the fx loop. – 5. Fx loop: fx return: 1/4" mono jack socket for the connection of the output of an external fx unit. This can also be used as a – slave in for the power amp....
Page 10
10 channel 1 & 2 sample settings sparkling clean - single coil pushed clean - hb spanked crunch cool clean crunch - dimed mo lead - dimed mo.
Page 11
11 l z b 1 2 3 4 l z b 1 2 3 4 l z b 1 2 3 4 l z b 1 2 3 4 2 x12 system using 1x gh50r head 1x gs212vr 4 x12 system using 1x gh50r-212 1x gs212vr connect to the two 16 ohm sockets. Connect to the two 8 ohm sockets. Integral speakers 8 x12 system using 1x gh100r head 2x gs412vr sample mono systems al...
Page 12
12 l z b 1 2 3 4 l z b 1 2 3 4 stereo system using 2x gh100r heads 1x gs412vr & fx unit stereo system using 2x gh50r heads 1x gs212vr & fx unit connected to the two single 8 ohm sockets. Guitar connected to this amp guitar connected to this amp fx unit fx unit output rh output rh input input output ...
Page 13
13 l z b 1 2 3 4 l z b 1 2 3 4 stereo system using 2x gh100r heads 2x gs412vr & fx unit connected to the two 8 ohm sockets. Guitar connected to this amp mono stereo all cabinet mode selection switches on this page are set to stereo fx unit output rh input output lh.
Page 14
Tube amplifier survival tips • tube amplifiers generally sound much warmer/sweeter than solid state transistor amplifiers, but they also need a little more respect due to the fragile glass tubes themselves. The ghr range uses top quality tubes, which should give you years of trouble free service. Ho...
Page 15: Tube Removal
Similarly when turning off your system always turn down the volume controls on your guitar amplifier and then turn off its power before turning off other equipment. Cables: never use shielded or microphone cable for any speaker connections as this will not be substantial enough to handle the amplifi...
Page 16: Power Cord When Not In Use.
15 signal path block diagrams always switch off and disconnect power cord when not in use. Footswitch input reverb ch1 drive ch2 drive bright eq bass mid treble ch2 volume reverb level send return fx-loop aux in bright pull mid chanel select v3b d.I. Out on/off d.I. Level 16 ohm 2 x16 ohm 8 ohm 2 x ...
Page 17: Power Cord When Not In Use.
17 always switch off and disconnect power cord when not in use. Footswitch reverb eq bass mid treble ch2 volume reverb level send return fx-loop aux in pull mid chanel select v3b d.I. Out on/off d.I. Level 16 ohm 2 x16 ohm 8 ohm 2 x 8 ohm 4 ohm gnd link cabinet emulation d.I amp gh100r input ch1 dri...
Page 18
Specifications 18 supply voltage ~100v, ~120v, ~220v, ~230v, ~240v 50/60hz factory option mains fuse (~220v>240v = t2a l 250v) (~100>120v = t5a l 250v) ht fuse gh100r - t1a l, gh50r/gh50r-212 - t500ma l power consumption (max) gh100r - 300w, gh50r/gh50r-212 - 200w output power rating gh100r - 100w, ...
Page 19
Fcc compliancy statement this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference 2) this device must accept any interference received, that may cause undesired operation. Warning: changes or modificat...
Page 20
Please complete for future reference. Model number: serial number: place of purchase: date of purchase:.