Laney HCM160B User Manual - page 5
Laney
1.
3
1
2
3
4
5
6
7
8
9
10
11
12
14
HCM160B Rear Panel
13
15
Designed in the UK by BLT Industries LTD.
W
ARNING
- T
HIS
EQUIPMENT
MUST
BE
EARTHED
.
W
ARNING
- T
O
REDUCE
THE
RISK
OF
FIRE
OR
ELECTRIC
SHOCK
DO
NOT
EXPOSE
THIS
APPLIANCE
TO
RAIN
OR
MOISTURE
.
C
AUTION
- T
O
REDUCE
THE
RISK
OF
ELECTRIC
SHOCK
DO
NOT
REMOVE
COVERS
.N
O
USER
SERVICEABLE
PARTS
INSIDE
.
R
EFER
SERVICING
TO
QUALIFIED
PERSONNEL
ONLY
.
A
TTENTION
- R
EMPLACER
LE
FUSIBLE
SEULEMENT
PAR
LE
MEME
TYPE
ET
LE
MEME
CALIBRE
.
A
TTENTION
- D
EBRANCHER
LE
CORDON
D
’
ALIMENTATION
AVANT
TOUTE
INTERVENTION
.
A
VIS
- R
ISQUE
DE
CHOC
ELECTRIQUE
-
NE
PAS
OUVRIR
.
C
AUTION
- F
OR
CONTINUED
PROTECTION
AGAINST
RISK
OF
FIRE
REPLACE
ONLY
WITH
SAME
TYPE
AND
RATED
FUSE
.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
Tuner Out
FX Return
FX Send
Extension
Loudspeaker
S
ERIAL
N
UMBER
8
OHM
M
INIMUM
I
MPEDANCE
R
EFER
TO
U
SER
M
ANUAL
F
OR
L
OUDSPEAKER
C
ONNECTIONS
Made in China
Fabrique en Chine
~100V AC 50/60Hz
Model
Power Source
Primary Fuse
~230V AC 50/60Hz
~120V AC 50/60Hz
~240V AC 50/60Hz
T5A L / 125V
T2A L / 250V
HCM160B
HCM160B Front Panel
TREBLE: Controls the high-frequency response of the pre-amplifier.
LIMITER SWITCH: Allows the on-board LIMITER to be defeated if desired. With the switch
in the out position the limiter is engaged. The limiter is automatically triggered at high-output
levels and is designed to prevent power-amp distortion at high-output levels. When the
limiter is automatically triggered an LED lights up to indicate the limiter is active. It is possible
to have the limiter engaged but not have the LED active. The limiter monitors both power-
amp clipping and load so it automatically registers the cabinet-impedance and sets itself
accordingly.
VOLUME : Sets the overall listening level of the amplifier.
D.I: XLR socket for direct-injection of the amplifier signal to a mixing-desk or additional
power-amplifier. The XLR socket provides a low-impedance balanced output-signal.
POWER SWITCH.
POWER SOCKET: Socket for connecting mains power. Please note that the mains power
fuse is also located here. Replace only with same type and rating..
EXTENSION SPEAKER SOCKET: This socket(s) should be used to connect an extension-
cabinet. The impedance of the extension-cabinet must not be less than 8 Ohms.
Connecting cabinets that have a lower impedance than 8 Ohms will result in the amplifier
overheating.; Continual use in this manner may cause permanent damage. Connecting a
cabinet with an impedance of greater than 8 Ohms will cause no damage to the amplifier but
will result in a reduced output.
TUNER SOCKET: Socket for connecting external tuner.
FX LOOP: Send and return sockets are provided for connecting external effects-units..
7
8
9
10
11
12
13
15
14