Summary of Iommi TI100
Page 2
Warning: when using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions safe. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do no...
Page 3
Attention: l’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4. Suivez ces instructions. 5. N’utilisez pas cette unité pr...
Page 4
Achtung: beim einsatz von elektrogeräten müssen u.A. Grundlegende vorsichtsmaßnahmen befolgt werden: 1. Lesen sie sich diese anweisungen durch. 2. Bewahren sie diese anweisungen auf. 3. Beachten sie alle warnungen. 4. Befolgen sie alle anweisungen. 5. Setzen sie dieses gerät nicht in der nähe von wa...
Page 5
Cuidado: cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6. Limpiar solamente con una...
Page 7
Specifications ~100v>~120v ~220v, ~230v,~240v t1a l features: twin channels - lead & rhythm switchable pre-boost on both channels - led indicates ac tive fx loop - side chain - insert - bypass, with fx return gain control footswitchable channels, pre-boost on/off on each channel, with supplied fs4-t...
Page 9
“it began with a clap of thunder and a tolling bell. Then, as a heavily distorted guitar played a diminished fifth – an interval once banned by the roman catholic church for being the devil’s interval – a male voice started to wail as if from the grave…… and music was never the same again.” the date...
Page 10
Front panel controls lead channel rhythm channel lead & rhythm channels are provided, both can have different settings and be switched between with the channel switch (8) or footswitch if connected. Although the functions of the controls on each channel are similar, the sounds can be very different....
Page 11: Always Switch Off
Always switch off and disconnect power cord when not in use front panel controls volume: controls the volume of each channel independantly. Experiment with different combinations of the drive and volume controls to achieve different sounds. Reducing the drive while increasing the volume will result ...
Page 12
Rear panel controls mains inlet socket: make sure the voltage indicated on the rear panel is correct for your country! Mains fuse: this drawer contains the main safety fuse for the unit. The fuse protects the amplifier from damage in the event of fault by disconnecting the mains power supply. Ht fus...
Page 13
Rear panel controls effects loop return: connect the output from your external effects to this socket. Control allowing you to make up for any insertion loss that may occur in the fx processor. Use this mode when the whole of the amplifier signal needs routing through any external processors such as...
Page 14
Quick start settings use either channel clean crunch lead 1-3 volume as desired tony’s typical settings.
Page 15
User settings on on off off l r on on off off l r on on off off l r on on off off l r.
Page 16
Tube amp tips tube amplifiers generally sound much warmer/sweeter than solid state transistor amplifiers but they also need a little more respect due to the fragile glass tubes. The ti100 head uses eight 12ax7 preamp tubes, and four 6l6 output tubes which should give you years of trouble free servic...
Page 17
Block diagram input external loudspeaker 4-16 ohms power amp in pre amp out 16ohms side chain-insert-bypass shown in side chain mode sym link out sym link in footswitch lead eq rhythm eq bass bass mid mid treble treble lead volume fx level rhythm volume channel switch lead drive rhythm drive 8ohms 2...
Page 18
Sample setups fx unit fs4-ti l z b 1 2 3 4 l z b 1 2 3 4 ti412s.
Page 19
L z b 1 2 3 4 fx unit l z b 1 2 3 4 l z b 1 2 3 4 l z b 1 2 3 4 master master fs4-ti ti412s ti412s slave all of the preamp controls are disabled on the slave amp, only the dynamics & presence controls are operational, (see page 13). Slave.
Page 20
Operating instructions - issue 1.3.