Laney LC15-110 Operating Instructions Manual - page 12
TUBE AMPLIFIER SURVIVAL TIPS
V1
V2
V3
V4
V5
V6
V7
Page
12 / 16
• Tube amplifiers; generally sound much warmer/sweeter than solid state transistor amplifiers but they also need a little
more respect due to the fragile glass tubes themselves. The LC15-110 uses top quality tubes, which should give you years of
trouble free service, however like all tube amps; it is important to treat it with a certain amount of care.
• Tubes are fragile glass components; they can easily be damaged if thrown in and out of vehicles,
• Make sure the impedance; of your cabinets matches the setting on your amplifier. Improper impedance matching will
result in reduced output power output and compromised sound at best and amplifier failure/premature tube failure at worst.
• Allow the amplifier; to warm up to room temperature before switching it on, The sudden thermal shock generated can
crack the cold glass tube housing plus any moisture is bad news around high voltage electronics.
• Allow the amplifier; to cool down after playing before moving. Hot tubes are more susceptible to damage than cool
ones.Use good quality loudspeaker leads, cheap leads are often not up to the job of handling the large requirements for
loudspeakers and can often short out.
•
don't like running into a
circuit. A tubes life expectancy is based upon a number of factors which
include operating temperature, how hard and how often it is played, vibration due to travel etc. Tubes should be changed in
your amplifier if you notice any change in your amplifiers performance etc. They need not be changed at any regular interval.
• Typical problems; with preamp tubes can be a crackly noise, hiss, hum and microphony. The preamp tubes can safely be
changed with no action required if they fail or reduce in performance. Typical output tube problems can be blown HT fuse;
sound lacking in punch, sound lacks extreme highs or lows and low level hum. The Output tubes can be replaced singularly if
you replace them with the exact same type AND grade as factory fitted otherwise they should be replaced as a set. See the
diagram following to see how to check the tube grade fitted. Exact replacement preamp tubes and matched sets of output
tubes are available from Laney via your dealer.
• To change a tube; switch off the unit and unplug from the mains supply. Wait for the tubes to cool down. Lay amplifier
down on its front face and remove the protective grille held in place with four screws. You should now be able to access the
underside of the amplifier chassis. Preamp tubes are protected with a screen can, to remove; gently twist the screen can anti
clockwise and then pull up. The tube can then be gently pulled out. Take care when pushing the new tube in to make sure the
pins are all aligned properly. Output tubes have a spring retainer which must be pulled away before the tube will come out.
•
;
Tube amplifiers;
open
Amplifier connection In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off
your equipment. With all system parts connected, effects processors etc. BEFORE turning on your guitar amplifier. Many
products have large transient surges at turn on and off which can cause damage to your speakers. By turning on your guitar
amplifier LAST and making sure its Volume controls are set to minimum any transients from other equipment will not reach
Laney
LC
15
-1
10
Laney
Page
13 / 16
your loudspeakers. Wait until all system parts have stabilised; usually a couple of seconds. Similarly when turning off your
system always turn down the Volume controls on your guitar amplifier and then turn off its power before turning off other
equipment.
• Servicing: The user should not attempt to service these products. Refer all servicing to qualified service personnel.
BLOCK DIAGRAM
LC
15
-1
10
V1
ECC83
HIGRADE
V2+V3 ECC83
V4+V5 EL84
MATCHED SET
EL84
Grade Number
EL84
Grade Number
V1
V2
V3
V4
V5
INTERNAL
LOUDSPEAKER
HI INPUT
EXT. LOUDSPEAKER
DRIVE
LO INPUT
BRIGHT
BRIGHT
PAD
EQ
EQ
B
A
S
S
BRIGHT
M
ID
T
R
E
B
L
E
VOLUME
V1a
V2a
V2b
8-16 OHMS
V1b
V3a
V3b
V4
V5
FX RETURN
LINE OUT
FX SEND
BYPASS
0 dB
10dB
TONE
TONE
TONE
CONTROL
REVERB
REVERB
REVERB
LEVEL
FOOTSWITCH