Laney LV200 Instructions Manual

Other manuals for LV200: User Manual

Summary of LV200

  • Page 1

    200

  • Page 2

    Warning: when using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions safe. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do no...

  • Page 3

    Attention: l’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4. Suivez ces instructions. 5. N’utilisez pas cette unité pr...

  • Page 4

    Achtung: beim einsatz von elektrogeräten müssen u.A. Grundlegende vorsichtsmaßnahmen befolgt werden: 1. Lesen sie sich diese anweisungen durch. 2. Bewahren sie diese anweisungen auf. 3. Beachten sie alle warnungen. 4. Befolgen sie alle anweisungen. 5. Setzen sie dieses gerät nicht in der nähe von wa...

  • Page 5

    Cuidado: cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6. Limpiar solamente con una...

  • Page 6

    6 after unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the wiring convention...

  • Page 7

    In the interest of continued development, laney reserves the right to amend product specification without prior notification. Specifications block diagram input power amp drive1 clean drive1 scoop reverb eq section eq section fx return this loop is a series type so all of your signal will go through...

  • Page 8

    8.

  • Page 9

    200 the lv200 is a 65w open back three channel guitar combo loaded with a 12” custom designed loudspeaker. It features a true tube-loaded drive stage; separate three band eq for the clean and drive channels (drive 1 + 2 share) ; clean channel bright switch; drive channel ‘v’ preshape; headphone sock...

  • Page 10

    7 7 7 7 7 7 7 7 7 7 7 7 7 1 1 1 1 1 1 1 1 1 1 1 1 1 9 9 9 9 9 9 9 9 9 9 9 9 9 3 3 3 3 3 3 3 3 3 3 3 3 3 10 10 10 10 10 10 10 10 10 10 10 10 10 4 4 4 4 4 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 0 0 0 0 0 0 0 0 0 0 0 0 0 5 5 5 5 5 5 5 5 5 5 5 5 5 8 8 8 8 8 8 8 8 8 8 8 8 8 2 2 2 2 2 2 2 2 2 2 2 2 2 i...

  • Page 11: Power Cord When Not In Use

    18 19 20 21 22 17 11 always switch off and disconnect power cord when not in use 11 12 13 14 15 16 controls the overall level on the drive1 channel. Use in conjunction with . The vscoop switch drastically cuts out any mid frequencies present in the drive2 sound giving you a very modern, aggressive l...

  • Page 12

    L z b 1 2 3 4 8 7 6 5 4 3 1 12 rear panel power inlet socket. Make sure the specified voltage is correct for your country! This drawer contains the main safety fuse for the unit. The mains fuse ratings are detailed on page 7 of this manual displays the model number, power requirements and serial num...

  • Page 13

    L z b 1 2 3 4 in order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with normal household waste to landfill sites. It must be taken to an approved recycling centre according to the recommendations of the weee (waste electrical and electron...

  • Page 14

    Quick start settings - suggestions only, experiment! 14 7 7 7 7 7 7 7 7 7 7 7 7 7 1 1 1 1 1 1 1 1 1 1 1 1 1 9 9 9 9 9 9 9 9 9 9 9 9 9 3 3 3 3 3 3 3 3 3 3 3 3 3 10 10 10 10 10 10 10 10 10 10 10 10 10 4 4 4 4 4 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 0 0 0 0 0 0 0 0 0 0 0 0 0 5 5 5 5 5 5 5 5 5 5 5 5...

  • Page 15

    15 amplifier connection: in order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. Before turning on your guitar amplifier. Many...

  • Page 16

    Operating instructions - issue: 1.1.