Laney RB8 Instructions Manual

Other manuals for RB8: User Manual

Summary of RB8

  • Page 1

    Richter bass.

  • Page 2

    Warning: when using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions safe. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do no...

  • Page 3

    Attention: l’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4. Suivez ces instructions. 5. N’utilisez pas cette unité pr...

  • Page 4

    Achtung: beim einsatz von elektrogeräten müssen u.A. Grundlegende vorsichtsmaßnahmen befolgt werden: 1. Lesen sie sich diese anweisungen durch. 2. Bewahren sie diese anweisungen auf. 3. Beachten sie alle warnungen. 4. Befolgen sie alle anweisungen. 5. Setzen sie dieses gerät nicht in der nähe von wa...

  • Page 5

    Cuidado: cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6. Limpiar solamente con una...

  • Page 6

    6 after unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the wiring convention...

  • Page 7: Rb9

    7 in order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with normal household waste to landfill sites. It must be taken to an approved recycling centre according to the recommendations of the weee (waste electrical and electronic equipment...

  • Page 8

    8.

  • Page 9

    This straight-up, no nonsense 160 watt rb4 bass combo features a 15" custom speaker, bass, treble and seven band graphic mid eq, switchable compressor and switchable limiter in a solid cabinet with top and side handles. Exactly what you need for gigging, recording or just making a noise in your gara...

  • Page 10

    10 front panel controls 3 2 1 11 12 13 7 6 10 9 5 8 4 3 1 2 normal and high inputs are provided for connection of bass guitars. High output basses, either active or passive should be connected via the high socket. Low output basses should be connected using the normal input. High output basses may a...

  • Page 11

    11 12 13 10 9 8 6 7 4 5 always switch off and disconnect power cord when not in use the enhance control provides an increased definition at the low-end of the frequency spectrum giving you a tighter, punchier sound. The enhance control does this by providing a dip in the frequency-response of the am...

  • Page 12

    12 rear panel controls 4 5 3 2 1 all controls common - unless otherwise stated voltage selection switch: this is factory set to the correct voltage for the region the product is supplied to. If necessary it can be reset by removing the mains lead and then loosening (but not removing) the screws secu...

  • Page 13

    7 8 6 these sockets should be used to connect to your loudspeaker cabinets. The total impedance of the cabinets must not be less than 4 ohms. Connecting cabinets that have a lower impedance than 4 ohms will result in the amplifier overheating. Continual use in this manner may cause permanent damage....

  • Page 14

    14 found some cool settings you want to keep? Make a note of them here: systems & settings tuner input fx unit rb115 40hz 80hz 160hz 400hz 800hz 6khz 2khz 0db 0db -15 -15 +15 +15 limiter defeat volume d.I. Comp high normal enhance bass treble gain on 2 4 4 2 5 1 1 5 0 3 3 - + 2 4 4 2 5 1 1 5 0 3 3 -...

  • Page 15

    15 amplifier connection: in order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. Before turning on your bass amplifier. Many p...

  • Page 16

    Operating instructions - issue: 1.