- DL manuals
- Laney
- Musical Instrument Amplifier
- TT100H
- Operating Instructions Manual
Laney TT100H Operating Instructions Manual
Summary of TT100H
Page 1
Modern all tube guitar head amplifier power to the music laney t 0h / 10 h t 5 tt 0 o p e r a t in g i n st r u c t io n s - 2 .2 w w w . L a n e y . C o . U k.
Page 2
Save these instructions important safety instructions warning: when using electric products, basic cautions should always be followed, including the following. 1. Read all safety and operating instructions before using this product 2. The product should be powered by a three pin `grounded (or earthe...
Page 3
Page 3/24 / tt 50 h tt 10 0h precaucion: precaucion: advertencia: este simbolo tiene el proposito de alertar al usuario de la presencia de ‘(voltaje) peligroso’ que no tiene aislamiento dentro de la caja del producto que puede tener una magnitud suficiente como para constituir riesgo de corrientazo....
Page 4
Before switching on after unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the...
Page 5
Introduction the dark art: in an age where guitar players have developed an unhealthy fascination with pre-amp distortion, the fabled sound of a tube power amp being pushed hard has almost passed into history. Until now that is! The tt50h and tt100h are modern versatile tube head amplifiers. They fe...
Page 6
Input: single jack input for connecting your instrument. Only use good quality guitar cable. Channel 1 switch: press in to activate channel 1, the led will illuminate when active. Channel 1 is designed to give the crispest clean tones around. This switch is footswitchable and midi controllable, for ...
Page 7
For more information on midi see the midi section later in the manual. Drive: sets the level of tube preamplifier gain or how dirty your sound is for the drive channel - channel 2. This control should be used in conjunction with the master (11) setting low levels of drive with high levels of master ...
Page 8
Bright: adds edge and picking emphasise to you sound. This control has more effect at lower drive (10) settings. Modern: the modern switch applies a degree of compression to the signal, providing massive smooth sustain. Xpand: at high gain and volume settings the natural tendancy for a tube amplifie...
Page 9
Pre-amplifier, so sends to the fx loops and record out are maintained allowing signal levels to be monitored silently and allow silent recording via the record out. Reverb: sets the overall master level of the reverb. Use in conjunction with the individual channel reverb send level controls. Fx mix:...
Page 10
Power inlet socket: connect to your power source. Make sure the specified voltage is correct for your country! Power fuse: this is the main safety fuse for the unit. The fuse protects the ac power to the amplifier. Use only the correct size and rating of fuse as specified on the panel. If a fuse blo...
Page 11
Page 11/24 will result in masmatched impedance and will reduce the amplifiers performance and in some cases may cause damage to the amplifier. You may connect 1*4ohm, 1*8ohm, 2*8ohm, 2*16ohm cabinets to these sockets. Do not use at the same time as the 16 ohm socket. 16 ohm socket: use to connect a ...
Page 12
Laney operating instructions the advantage of having midi in your guitar amplifier is that it allows your amplifier and external devices (like fx controllers) to talk with each other. At last you can press one button to select the amplifier channel, and choice of effects on multiple devices all at o...
Page 13
Channel 2 + volume 1 = program 1 channel 2 + volume 2 = program 4 channel 3 + volume 1 = program 2 channel 3 + volume 2 = program 5 you then need to midi map desired fx to the above program changes on your fx processor. This gives 3 channel sounds, each at 2 different volume levels each with differe...
Page 14
In this configuration the tt amplifier is a slave device ,its setting being called up by the midi controller. This midi controller could be a device which purely generates midi information or a multi effects pedal board. To setup the amplifier you need to do the following:- 1. Select the required pa...
Page 15
Laney operating instructions page 15/24 quick start settings - suggestions only! Experiment crystal clean blues clean blues lead h /t t1 h tt 50 00
Page 16
Laney operating instructions page 16 /24 quick start settings - continued rock rhythm rock lead metal h /t t1 h tt 50 00
Page 17
Laney operating instructions page 17/24 user settings - storte your own cool sounds here 0h /t t1 h tt 5 00
Page 18
Laney operating instructions tube amplifier survival tips " take care when moving the amplifier. Tubes are fragile glass components, they can easily be damaged if thrown in and out of transit vans etc. " make sure the impedance of your cabinets matches the setting on your amplifier. Improper impedan...
Page 19
El34b grade number el34b grade number laney operating instructions page 19/24 v4 v4 v3 v3 v5 v5 v6 v6 v7 v7 v8 v8 v1 v1 v2 v2 tube amplifier survival tips - continued 0h /t t1 h tt 5 00 tt50h tube layout tt100h tube layout v4 v4 v3 v3 v5 v5 v6 v6 v9 v9 v10 v10 v1 v1 v2 v2 v7 v7 v8 v8 v1 ecc83 (high ...
Page 20
Laney operating instructions laney operating instructions general notes amplifier connection: in order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, ...
Page 21
Laney operating instructions page 21/24 midi out tt sample system 2 midi controller 0h /t t1 h tt 5 00 input fx controller output 8 ohms link model rb115 power rating 300w program model rb115 power rating 300w program serial number: serial number: input laney power to the music www.Laney.Co.Uk desig...
Page 22
Laney operating instructions laney operating instructions page 22/24 input drive drive channel2 channel3 eq eq channel1 eq volume/ bright master volume line out fx send fx return reverb return mute presence record out fx mix master reverb output stage channel switching master volume master volume 2 ...
Page 23
Laney operating instructions page 23/24 0 v h 1 0r laney operating instructions supply voltage ~100v, ~120v, ~220v, ~230v, ~240v 50/60hz factory option mains fuse tt50h (~220v>240v = t2a l 250v) (~100>120v = t5a l 250v) ht fuse tt50h = t1a l power consumption tt50h = 200w tt100h = 300w output power ...
Page 24
In the interest of continued product development, laney reserves the right to amend product specification without prior notification. Power to the music laney jazz ampicons are here to help! Blues rock metal w w w . L a n e y . C o . U k l a n e y a m p l i f i c a t i o n.