1. DL manuals
  2. Lanner
  3. Security System
  4. UP-2010
  5. User Manual

Lanner UP-2010 User Manual - Replacing The Cooling Fans

Manual is about: rackmount network security appliance

Summary of UP-2010

  • Page 1

    Network communications hardware platforms for network computing up-2010 v1.1 user's manual release date: 2016/03/04.

  • Page 2: Overview

    Overview icon descriptions the icons are used in the manual to serve as an indication of interest topics or important messages. Below is a description of these icons: note: this check mark indicates that there is a note of interest and is something that you should pay special attention to while usin...

  • Page 3: Emc Notice

    Lithium battery caution: risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions operating safety electrical equipment generates heat. Ambient air temperature may not be adequate to cool equipment to acceptable operating temperatures wit...

  • Page 4: Chapter 1:  Introduction

    Table of contents overview 2 chapter 1: introduction 5 system specification 5 package contents 6 chapter 2: system components 7 mechanical drawing 7 block diagram 8 front components 9 rear components 10 chapter 3: motherboard information 11 inside up-2010 11 jumpers & connectors on the intel rangele...

  • Page 5: Chapter 1:

    Chapter 1: introduction thank you for choosing lanner up-2010. Lanner up-2010 is an enterprise-class 1u rackmount network security appliance with high-density ethernet ports and poe capability. Built with intel® atom™ c2000 processor, the appliance can offer efficient packet processing abilities and...

  • Page 6: Package Contents

    Package contents your package contains the following items: 1 – wg-up2010 poe switch system • 2 – power cable • 1 – ear rack mount kit with screws • 1 – console cable • 1 – lan cable (red) • 1 – doc kit for wg • note: if you should find any components missing or damaged, please contact your dealer i...

  • Page 7: Chapter 2:

    Chapter 2: system components mechanical drawing.

  • Page 8: Block Diagram

    Block diagram psu intel rangeley platform c2758 ddr3 1600 ecc so-dimm cf card psu pcie x8 *2.

  • Page 9: Front Components

    Front components component description remarks f1 led indicators power/status/hdd f2 console 1 x rj-45 port to be connected with a terminal pc for diagnose and management purposes f3 usb 2.0 ports 2 x usb 2.0 type a connectors. F4 management 1 x rj-45 management port f5 lan ports 24 x ethernet lan p...

  • Page 10: Rear Components

    Component description remarks r1 fan 2 x cooling fans r2 psu 500w power supply unit rear components r1 r2.

  • Page 11: Chapter 3:

    Chapter 3: motherboard information inside up-2010 the internal of up-2010 is a composition of the intel rangeley main board and a pcie module board for high- density network ports powered by marvell engines and intel controllers. The main intel rangeley board pcie i/o board intel rangeley intel i210...

  • Page 12

    Jumpers & connectors on the intel rangeley main board j4 j3 j20 jbat1 j21 dimm1 dimm2 cf1 fan1 fan2 fan3 sata 6g1 ps4s1 ps4s2 pkmb1 lpc1 usb2 spirom1 pcie1 pcie2.

  • Page 13

    J6 j5 jumpers & connectors on the pcie i/o board usb1 com1 rj1 rj2 rj4 rj3 spirom1 pciec1 pciec2 cn1 pwr1 pwr2.

  • Page 14: Connectors and Jumpers List

    Connectors and jumpers list connectors/jumpers on the intel rangeley board labels function dimm 1,2 2x ddr so-dimm sockets fan1, 2, 3 3 x fan connectors cf1 1 x compactflash socket sata6g1 1 x sata port at 6gbps interface ps4p1 1 x sata 4-pin power connector ps4p2 1 x sata dom power connector pkmb1 ...

  • Page 15

    Jumper settings & connector pinouts on the intel rangeley main board j4: reset mode setting j3: rtest clear j20: tpm physical presence select j21 at mode select pin no. Description 1 hw reset 2 switch input (default 1-2) 3 sw reset pin no. Description 1 nc 2 avn_rtest_n 3 gnd cf1: compactflash socke...

  • Page 16

    Sata6g1: sata port ps4s1: sata 4-pin power port ps4s2: sata dom power connector pin no. Description 1 gnd 2 tx+ 3 tx- 4 gnd 5 rx- 6 rx+ 7 gnd pin no. Description 1 12v 2 gnd 3 gnd 4 5v pkmb1: keyboard/mouse pin header pin no. Description pin no. Description 1 +p5v_km 2 ms_l_clk 3 ms_l_dat 4 nc 5 kb_...

  • Page 17

    Pcie1: pcie x 8 lane socket pin no. Side b side a 1 +12v nc 2 +12v +12v 3 +12v +12v 4 gnd gnd 5 smb_clk clk_en 6 smb_dat p3v3 7 gnd p3v3 8 p3vsb p3v3 9 p3vsb p3vsb 10 p3vsb p3vsb 11 pmu_wake# pltrst_pcie_n 12 p3v3 gnd 13 p3v3 sio_gp44 14 gnd sio_gp45 15 gnd gnd 16 pcie_avn_c_txp15 pcie_avn_rxp15 17 ...

  • Page 18: Pcie I/o Board

    Jumper settings & connector pinouts on the pcie i/o board j6: mdc/mdio i/f option j5: ethernet switch debug port usb1: dual usb connectors pin no. Description pin no. Description 1 +p5v_usb0_l 5 +p5v_usb0_l 2 usb0_sb_l_dn 6 usb1_sb_l_dn 3 usb0_sb_l_dp 7 usb1_sb_l_dp 4 gnd 8 gnd pin no. Description 1...

  • Page 19

    Rj2/3: rj45 8 port connector w/transformer (2x4) pin no. Description pin no. Description a/c/e/g 1 tdp0 b/d/f/h 1 tdp0 a/c/e/g 2 tdn0 b/d/f/h 2 tdn0 a/c/e/g 3 tdp1 b/d/f/h 3 tdp1 a/c/e/g 4 tdn1 b/d/f/h 4 tdn1 a/c/e/g 5 tdp2 b/d/f/h 5 tdp2 a/c/e/g 6 tdn2 b/d/f/h 6 tdn2 a/c/e/g 7 tdp3 b/d/f/h 7 tdp3 a...

  • Page 20

    Pciec2: pcie x 8 lane connector (gold fingers) pin no. Side b side a 1 +12v nc 2 +12v +12v 3 +12v +12v 4 gnd gnd 5 smb_clk clk_en 6 smb_dat p3v3 7 gnd p3v3 8 p3vsb p3v3 9 p3vsb p3vsb 10 p3vsb p3vsb 11 pmu_wake# pltrst_pcie_n 12 p3v3 gnd 13 p3v3 sio_gp44 14 gnd sio_gp45 15 gnd gnd 16 pcie_avn_c_txp15...

  • Page 21: Chapter 4:

    Chapter 4: hardware setup preparing the hardware installation warning: to reduce the risk of personal injury, electric shock, or damage to the equipment, please make sure the device is totally powered off and without any power source connected. Shut off the system and remove all power 1. Connections...

  • Page 22

    Installing a compactflash card the system comes with a cf card slot on the intel rangeley main board. Please follow the steps below for installation. 1. Locate the cf card slot nearby the cpu. 2. Insert the cf card until firmly seated. Note: the device has an error proof design so that the card will...

  • Page 23: Replacing The Cooling Fans

    Replacing the cooling fans please follow the instructions below to replace the cool- ing fans in case they are worn out. 1. Loosen and remove the 4 screws on the fan. 2. Remove the fan connector(s) and take out the used fan. 3. Install a new one by connecting the fan connectors and fix it with 4 scr...

  • Page 24: Appendix A:

    Appendix a: programming watchdog timer a watchdog timer is a piece of hardware that can be used to automatically detect system anomalies and reset the processor in case there are any problems. Generally speaking, a watchdog timer is based on a counter that counts down from an initial value to zero. ...

  • Page 25: Appendix C:

    Appendix c: on linux follow these instructions when installing the intel® lan controller base driver for the in red hat® and linux operating system. Insert the motherboard/system support cd to the 1. Optical drive and mount the optional drive in the linux platform. Copy the base driver tar file from...

  • Page 26: Appendix D:

    Appendix d: terms and conditions warranty policy all products are under warranty against defects in 1. Materials and workmanship for a period of one year from the date of purchase. The buyer will bear the return freight charges for 2. Goods returned for repair within the warranty period; whereas the...